Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Front Driver Side - Side Squib Circuit  B1821/55  Open in Front Driver Side - Side Squib Circuit  B1822/55  Short to GND in Front Driver Side - Side Squib Circuit  B1823/55  Short to B+ in Front Driver Side - Side Squib Circuit  


DESCRIPTION

The driver side - side squib circuit consists of the center airbag sensor and the driver side front seat side airbag.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side - side squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1820/55 Center airbag sensor receives a line short signal 5 times in the driver side front seat side squib circuit during primary check.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat wire LH (for LHD)

·

Front seat wire RH (for RHD)

·

Seat airbag wire

·

Front seat side airbag LH (Driver side front seat side squib) (for LHD)

·

Front seat side airbag RH (Driver side front seat side squib) (for RHD)

·

Center airbag sensor


B1821/55 Center airbag sensor receives an open signal in the driver side front seat side squib circuit for 2 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat wire LH (for LHD)

·

Front seat wire RH (for RHD)

·

Seat airbag wire

·

Front seat side airbag LH (Driver side front seat side squib) (for LHD)

·

Front seat side airbag RH (Driver side front seat side squib) (for RHD)

·

Center airbag sensor


B1822/55 Center airbag sensor receives a short to ground signal in the driver side front seat side squib circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat wire LH (for LHD)

·

Front seat wire RH (for RHD)

·

Seat airbag wire

·

Front seat side airbag LH (Driver side front seat side squib) (for LHD)

·

Front seat side airbag RH (Driver side front seat side squib) (for RHD)

·

Center airbag sensor


B1823/55 Center airbag sensor receives a short to B+ signal in the driver side front seat side squib circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat wire LH (for LHD)

·

Front seat wire RH (for RHD)

·

Seat airbag wire

·

Front seat side airbag LH (Driver side front seat side squib) (for LHD)

·

Front seat side airbag RH (Driver side front seat side squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

U189425E02
0.281,0.406 1.156,0.594 0.875,0.188 10 false for LHD: 0.281,4.063 1.156,4.25 0.875,0.188 10 false for RHD: 4.896,1.208 5.333,1.417 0.438,0.208 10 false SFD+ 4.896,2.083 5.333,2.292 0.438,0.208 10 false SFD- 4.896,5.156 5.333,5.365 0.438,0.208 10 false SFD+ 4.896,6.021 5.333,6.229 0.438,0.208 10 false SFD- 4.771,3.104 6.198,3.427 1.427,0.323 10 false M9 4.76,7.073 6.188,7.396 1.427,0.323 10 false N10 1.031,6.323 3.135,6.792 2.104,0.469 10 false e1 4.073,1.24 4.385,1.448 0.313,0.208 10 false MX2 4.167,1.052 4.323,1.219 0.156,0.167 10 false 1 3.188,1.24 3.458,1.417 0.271,0.177 10 false Xf1 3.25,1.052 3.406,1.219 0.156,0.167 10 false 1 4.083,2.104 4.396,2.313 0.313,0.208 10 false MX2 4.167,1.938 4.323,2.104 0.156,0.167 10 false 2 4.677,1.146 4.833,1.313 0.156,0.167 10 false 9 4.604,2 4.792,2.167 0.188,0.167 10 false 10 3.188,2.104 3.458,2.281 0.271,0.177 10 false Xf1 3.25,1.938 3.406,2.104 0.156,0.167 10 false 2 2.74,1.146 2.896,1.313 0.156,0.167 10 false 1 2.74,2 2.896,2.167 0.156,0.167 10 false 2 4.052,5.156 4.385,5.365 0.333,0.208 10 false NW2 4.167,4.979 4.323,5.146 0.156,0.167 10 false 1 3.167,5.156 3.469,5.333 0.302,0.177 10 false We1 3.25,4.979 3.406,5.146 0.156,0.167 10 false 1 4.052,6.031 4.385,6.24 0.333,0.208 10 false NW2 4.167,5.844 4.323,6.01 0.156,0.167 10 false 2 4.677,5.073 4.833,5.24 0.156,0.167 10 false 9 4.604,5.927 4.792,6.094 0.188,0.167 10 false 10 3.156,6.031 3.479,6.208 0.323,0.177 10 false We1 3.25,5.844 3.406,6.01 0.156,0.167 10 false 2 2.74,5.073 2.896,5.24 0.156,0.167 10 false 1 2.74,5.927 2.896,6.094 0.156,0.167 10 false 2 1.01,2.594 3.115,2.99 2.104,0.396 10 false Driver Side Front Seat Side Squib 1.021,2.417 3.125,2.813 2.104,0.396 10 false f1 4.771,3.25 6.198,3.573 1.427,0.323 10 false Center Airbag Sensor 1.031,6.5 3.135,6.969 2.104,0.469 10 false Driver Side Front Seat Side Squib 4.75,7.25 6.177,7.573 1.427,0.323 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK DRIVER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY (DRIVER SIDE FRONT SEAT SIDE SQUIB)
C366263E01
4,0.333 4.333,0.583 0.333,0.25 4,0.667 4.333,0.917 0.333,0.25 0.938,1.281 0.938,0.854 false 4.094,2.333 4.302,1.979 false 4.552,2.375 4.396,2.125 false 1.01,0.49 1.323,0.688 0.313,0.198 10 false H 1.198,0.49 1.51,0.688 0.313,0.198 10 false G 1.5,0.49 1.813,0.688 0.313,0.198 10 false F 1.604,0.49 1.917,0.688 0.313,0.198 10 false E 1.885,0.49 2.198,0.688 0.313,0.198 10 false D 2.01,0.49 2.323,0.688 0.313,0.198 10 false C 2.448,0.719 2.76,0.917 0.313,0.198 10 false A 2.344,1.25 3.198,1.646 0.854,0.396 10 false Center Airbag Sensor 0.656,1.302 2.031,1.771 1.375,0.469 10 false Driver Side Front Seat Side Squib 4.115,0.365 4.427,0.563 0.313,0.198 10 false f1 4.823,0.031 5.938,0.281 1.115,0.25 10 false Connector G 5.604,1.604 6.292,1.865 0.688,0.26 10 false DTC 55 4.156,1.604 4.698,1.844 0.542,0.24 10 false DLC3 3.938,2.375 4.25,2.573 0.313,0.198 10 false CG 4.5,2.396 4.813,2.594 0.313,0.198 10 false TC 1.438,2.344 2.5,2.792 1.063,0.448 10 false *1: for LHD 4.094,0.698 4.406,0.896 0.313,0.198 10 false e1 4.385,0.365 4.698,0.563 0.313,0.198 10 false *1 4.375,0.698 4.688,0.896 0.313,0.198 10 false *2 2.479,2.344 3.542,2.792 1.063,0.448 10 false *2: for RHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the driver side front seat side airbag squib.


d.

Connect SST (resistance 2.1 Ω) to connector G.


CAUTION:

Never connect a tester to the driver side front seat side airbag (driver side front seat side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822, B1823 or 55 is not output.


HINT:

DTCs other than DTC B1820, B1821, B1822, B1823 or 55 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE DRIVER SIDE FRONT SEAT SIDE AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from the connector G.


d.

Check that the seat airbag wire connectors (on the driver side front seat side airbag) are not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK FRONT SEAT SIDE AIRBAG SQUIB CIRCUIT

NG

4.CHECK SEAT AIRBAG WIRE
3.CHECK FRONT SEAT SIDE AIRBAG SQUIB CIRCUIT
U189112E02
0.219,1.24 0.219,1.5 false 0.042,3.979 0.802,4.156 0.76,0.177 10 false *1: for LHD 0.042,4.313 0.833,4.49 0.792,0.177 10 false *2: for RHD 2.188,1.688 3.094,2.031 0.906,0.344 10 false Center Airbag Sensor 2.344,1.031 2.49,1.177 0.146,0.146 10 false A 2,0.813 2.146,0.958 0.146,0.146 10 false B 1.604,0.813 1.75,0.958 0.146,0.146 10 false C 1.49,0.813 1.635,0.958 0.146,0.146 10 false D 1.094,0.813 1.24,0.958 0.146,0.146 10 false E 0.99,0.813 1.135,0.958 0.146,0.146 10 false F 0.604,0.813 0.75,0.958 0.146,0.146 10 false G 0.719,2.646 1.573,2.823 0.854,0.177 10 false Connector G 0.104,1.51 1.552,1.885 1.448,0.375 10 false Driver Side Front Seat Side Squib 1.802,3.26 1.948,3.427 0.146,0.167 10 false f1 1.76,3.604 1.938,3.771 0.177,0.167 10 false e1 0.313,0.813 0.438,0.979 0.125,0.167 10 false H 2.052,3.25 2.24,3.427 0.188,0.177 10 false *1 2.052,3.604 2.24,3.781 0.188,0.177 10 false *2

a.

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
f1-1 - Body ground Below 1 V
f1-2 - Body ground

for RHD:
Tester Connection Specified Condition
e1-1 - Body ground Below 1 V
e1-2 - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
f1-1 - f1-2 Below 1 Ω
f1-1 - Body ground 1 MΩ or higher
f1-2 - Body ground

for RHD:
Tester Connection Specified Condition
e1-1 - e1-2 Below 1 Ω
e1-1 - Body ground 1 MΩ or higher
e1-2 - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
f1-1 - f1-2 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
e1-1 - e1-2 1 MΩ or higher




NG

4.CHECK SEAT AIRBAG WIRE

OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

4.CHECK SEAT AIRBAG WIRE
a.
U189113E02
0.844,1.094 0.844,0.302 0.844,0.302 0.906,0.302 false 0.208,1.24 0.208,1.573 false 2.281,1.677 3.177,2.031 0.896,0.354 10 false Center Airbag Sensor 2.427,1.031 2.552,1.188 0.125,0.156 10 false A 2.083,0.792 2.208,0.948 0.125,0.156 10 false B 1.719,0.792 1.844,0.948 0.125,0.156 10 false C 1.583,0.792 1.708,0.948 0.125,0.156 10 false D 1.219,0.792 1.344,0.948 0.125,0.156 10 false E 0.979,0.792 1.104,0.948 0.125,0.156 10 false F 0.573,0.792 0.698,0.948 0.125,0.156 10 false G 0.302,0.792 0.427,0.948 0.125,0.156 10 false H 0.104,1.583 1.292,1.948 1.188,0.365 10 false Driver Side Front Seat Side Squib 0.042,3.938 0.76,4.115 0.719,0.177 10 false *1: for LHD 0.042,4.26 0.781,4.438 0.74,0.177 10 false *2: for RHD 0.99,0.26 2.094,0.427 1.104,0.167 10 false Seat Airbag Wire 0.458,2.552 1.302,2.74 0.844,0.188 10 false Connector G 2.146,2.552 2.99,2.74 0.844,0.188 10 false Connector F 0.167,2.958 0.344,3.115 0.177,0.156 10 false f1 1.729,2.979 1.969,3.135 0.24,0.156 10 false Xf1 0.135,3.302 0.313,3.458 0.177,0.156 10 false e1 1.698,3.406 2,3.563 0.302,0.156 10 false We1 0.417,2.885 0.573,3.052 0.156,0.167 10 false *1 0.417,3.281 0.573,3.448 0.156,0.167 10 false *2 2.063,2.979 2.219,3.146 0.156,0.167 10 false *1 2.083,3.396 2.24,3.563 0.156,0.167 10 false *2

Disconnect the seat airbag wire connector from the front seat side squib circuit.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
f1-1 - Body ground Below 1 V
f1-2 - Body ground

for RHD:
Tester Connection Specified Condition
e1-1 - Body ground Below 1 V
e1-2 - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
f1-1 - Xf1-1 Below 1 Ω
f1-2 - Xf1-2
f1-1 - f1-2 1 MΩ or higher
f1-1 - Body ground
f1-2 - Body ground

for RHD:
Tester Connection Specified Condition
e1-1 - We1-1 Below 1 Ω
e1-2 - We1-2
e1-1 - e1-2 1 MΩ or higher
e1-1 - Body ground
e1-2 - Body ground




OK

5.CHECK FRONT SEAT WIRE

NG

REPAIR OR REPLACE SEAT AIRBAG WIRE

5.CHECK FRONT SEAT WIRE
a.
U189114E02
2,1.052 2,0.115 2,0.115 1.906,0.115 false 1.385,1.188 1.385,1.396 false 2.271,1.625 3.167,1.958 0.896,0.333 10 false Center Airbag Sensor 2.448,1 2.573,1.167 0.125,0.167 10 false A 2.104,0.76 2.229,0.927 0.125,0.167 10 false B 1.719,0.76 1.844,0.927 0.125,0.167 10 false C 1.521,0.76 1.646,0.927 0.125,0.167 10 false D 1.125,0.76 1.25,0.927 0.125,0.167 10 false E 0.906,0.76 1.031,0.927 0.125,0.167 10 false F 0.531,0.76 0.656,0.927 0.125,0.167 10 false G 0.302,0.76 0.427,0.927 0.125,0.167 10 false H 0.073,4.021 0.792,4.177 0.719,0.156 10 false *1: for LHD 0.073,4.333 0.802,4.49 0.729,0.156 10 false *2: for RHD 0.896,0.021 1.708,0.198 0.813,0.177 10 false Floor Wire*1 0.427,0.344 1.625,0.521 1.198,0.177 10 false Floor No. 2 Wire*2 0.271,1.406 1.625,1.594 1.354,0.188 10 false Front Seat Wire LH*1 0.271,1.708 1.646,1.896 1.375,0.188 10 false Front Seat Wire RH*2 0.469,2.656 1.302,2.813 0.833,0.156 10 false Connector E 2.156,2.656 2.99,2.813 0.833,0.156 10 false Connector D 0.188,3.01 0.438,3.177 0.25,0.167 10 false Xf1 0.104,3.51 0.427,3.677 0.323,0.167 10 false We1 1.729,2.979 2.177,3.146 0.448,0.167 10 false MX2 1.729,3.542 2.146,3.708 0.417,0.167 10 false NW2 0.427,3.167 0.583,3.344 0.156,0.177 10 false *1 2.073,3.125 2.229,3.302 0.156,0.177 10 false *1 0.438,3.677 0.594,3.854 0.156,0.177 10 false *2 2.094,3.688 2.25,3.865 0.156,0.177 10 false *2

Disconnect the front seat wire connector from the floor wire.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
Xf1-1 - Body ground Below 1 V
Xf1-2 - Body ground

for RHD:
Tester Connection Specified Condition
We1-1 - Body ground Below 1 V
We1-2 - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
Xf1-1 - MX2-1 Below 1 Ω
Xf1-2 - MX2-2 Below 1 Ω
Xf1-1 - Xf1-2 1 MΩ or higher
Xf1-1 - Body ground 1 MΩ or higher
Xf1-2 - Body ground 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
We1-1 - NW2-1 Below 1 Ω
We1-2 - NW2-2 Below 1 Ω
We1-1 - We1-2 1 MΩ or higher
We1-1 - Body ground 1 MΩ or higher
We1-2 - Body ground 1 MΩ or higher




OK

REPAIR OR REPLACE FLOOR WIRE

NG

REPAIR OR REPLACE FRONT SEAT WIRE