Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1830/57  Short in Driver Side Curtain Shield Squib Circuit  B1831/57  Open in Driver Side Curtain Shield Squib Circuit  B1832/57  Short to GND in Driver Side Curtain Shield Squib Circuit  B1833/57  Short to B+ in Driver Side Curtain Shield Squib Circuit  


DESCRIPTION

The driver side curtain shield squib circuit consists of the center airbag sensor and the driver side curtain shield airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1830/57 Center airbag sensor receives a line short signal 5 times in the driver side curtain shield squib circuit during primary check.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor


B1831/57 Center airbag sensor receives an open signal in the driver side curtain shield squib circuit for 2 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor


B1832/57 Center airbag sensor receives a short to ground signal in the driver side curtain shield squib circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor


B1833/57 Center airbag sensor receives a short to B+ signal in the driver side curtain shield squib circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C368098E01
0.25,0.271 0.865,0.625 0.615,0.354 10 false for LHD: 1.219,2.448 1.833,2.802 0.615,0.354 10 false M15 1.208,2.615 2.781,2.938 1.573,0.323 10 false Curtain Shield Squib LH 2.354,1.156 2.969,1.51 0.615,0.354 10 false ICL+ 2.74,1.156 3.125,1.396 0.385,0.24 10 false 2 2.729,2.01 3.115,2.25 0.385,0.24 10 false 1 4.656,1.125 5.042,1.365 0.385,0.24 10 false 7 4.656,1.99 5.042,2.229 0.385,0.24 10 false 6 4.781,3.167 5.167,3.406 0.385,0.24 10 false M9 4.781,3.344 6.708,3.656 1.927,0.313 10 false Center Airbag Sensor 4.875,1.25 5.26,1.49 0.385,0.24 10 false ICD+ 2.354,2.219 2.969,2.573 0.615,0.354 10 false ICL- 2.323,5.063 2.938,5.417 0.615,0.354 10 false ICR+ 4.875,2.115 5.26,2.354 0.385,0.24 10 false ICD- 4.823,7.073 5.208,7.313 0.385,0.24 10 false N10 4.823,7.24 6.75,7.552 1.927,0.313 10 false Center Airbag Sensor 1.323,6.385 1.708,6.625 0.385,0.24 10 false N13 1.313,6.552 2.885,6.875 1.573,0.323 10 false Curtain Shield Squib RH 2.313,6.135 2.927,6.49 0.615,0.354 10 false ICR- 2.74,5.042 3.125,5.281 0.385,0.24 10 false 2 2.74,5.948 3.125,6.188 0.385,0.24 10 false 1 4.625,5.052 5.01,5.292 0.385,0.24 10 false 7 4.625,5.938 5.01,6.177 0.385,0.24 10 false 6 4.865,5.167 5.25,5.406 0.385,0.24 10 false ICD+ 4.885,6.042 5.271,6.281 0.385,0.24 10 false ICD- 0.24,4 0.854,4.354 0.615,0.354 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK DRIVER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE CURTAIN SHIELD SQUIB)
C364213E02
4.167,0.5 4.583,0.75 0.417,0.25 4.167,0.833 4.583,1.083 0.417,0.25 0.75,1.417 0.75,1.188 false 4.271,2.49 4.438,2.167 true 4.615,2.49 4.5,2.313 true 0.823,0.854 1.135,1.052 0.313,0.198 10 false D 1.01,0.854 1.323,1.052 0.313,0.198 10 false C 1.323,1.573 2.781,2.031 1.458,0.458 10 false Center Airbag Sensor 0.073,1.427 1.219,1.76 1.146,0.333 10 false Driver Side Curtain Shield Squib 4.26,0.875 4.573,1.073 0.313,0.198 10 false N13 5.01,0.125 6.292,0.385 1.281,0.26 10 false Connector C 4.26,1.76 4.698,1.958 0.438,0.198 10 false DLC3 4.135,2.5 4.448,2.698 0.313,0.198 10 false CG 4.552,2.51 4.865,2.708 0.313,0.198 10 false TC 5.74,1.76 6.313,2.01 0.573,0.25 10 false DTC 57 4.26,0.552 4.573,0.75 0.313,0.198 10 false M15 4.635,0.552 4.948,0.75 0.313,0.198 10 false *1 4.635,0.875 4.948,1.073 0.313,0.198 10 false *2 3.042,2.365 4.208,2.792 1.167,0.427 10 false *2: for RHD 2.073,2.365 3.24,2.792 1.167,0.427 10 false *1: for LHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the driver side curtain shield airbag.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the driver side curtain shield airbag (driver side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1830, B1831, B1832, B1833 or 57 is not output.


HINT:

DTCs other than DTC B1830, B1831, B1832, B1833 or 57 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE DRIVER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the driver side curtain shield airbag) is not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)

NG

REPAIR OR REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB CIRCUIT)
U188968E02
0.802,0.792 0.802,1.063 false 1.396,0.792 1.396,1.906 false 1.219,3.625 1.667,3.542 true 2.281,4.125 1.792,3.542 true 2.188,1.219 3.073,1.542 0.885,0.323 10 false Center Airbag Sensor 1.896,0.646 2.021,0.823 0.125,0.177 10 false A 1.521,0.396 1.646,0.573 0.125,0.177 10 false B 1.125,0.385 1.25,0.563 0.125,0.177 10 false C 0.906,0.385 1.031,0.563 0.125,0.177 10 false D 0.031,1.094 0.865,1.615 0.833,0.521 10 false Driver Side Curtain Shield Squib 1.25,2.823 2.083,3 0.833,0.177 10 false Connector C 1.177,1.896 1.979,2.063 0.802,0.167 10 false Floor Wire*1 1.177,2.198 2.365,2.365 1.188,0.167 10 false Floor No. 2 Wire*2 2.323,3.313 2.646,3.458 0.323,0.146 10 false M15 2.323,3.698 2.615,3.854 0.292,0.156 10 false N13 2.719,3.448 2.896,3.625 0.177,0.177 10 false *1 2.677,3.865 2.854,4.042 0.177,0.177 10 false *2 2.177,4.167 2.667,4.354 0.49,0.188 10 false ICL+*1 2.177,4.354 2.667,4.542 0.49,0.188 10 false ICR+*2 0.688,3.552 1.177,3.74 0.49,0.188 10 false ICL-*1 0.688,3.75 1.177,3.938 0.49,0.188 10 false ICR-*2 0.302,4.083 1.042,4.25 0.74,0.167 10 false *1: for LHD 0.302,4.385 1.042,4.552 0.74,0.167 10 false *2: for RHD

a.

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
M15-1 (ICL-) - Body ground Below 1 V
M15-2 (ICL+) - Body ground

for RHD:
Tester Connection Specified Condition
N13-1 (ICR-) - Body ground Below 1 V
N13-2 (ICR+) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M15-1 (ICL-) - M15-2 (ICL+) Below 1 Ω
M15-1 (ICL-) - Body ground 1 MΩ or higher
M15-2 (ICL+) - Body ground

for RHD:
Tester Connection Specified Condition
N13-1 (ICR-) - N13-2 (ICR+) Below 1 Ω
N13-1 (ICR-) - Body ground 1 MΩ or higher
N13-2 (ICR+) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M15-1 (ICL-) - M15-2 (ICL+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
N13-1 (ICR-) - N13-2 (ICR+) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE