Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835/58  Short in Front Passenger Side Curtain Shield Squib Circuit  B1836/58  Open in Front Passenger Side Curtain Shield Squib Circuit  B1837/58  Short to GND in Front Passenger Side Curtain Shield Squib Circuit  B1838/58  Short to B+ in Front Passenger Side Curtain Shield Squib Circuit  


DESCRIPTION

The front passenger side curtain shield squib circuit consists of the center airbag sensor and the front passenger side curtain shield airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side curtain shield squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1835/58 Center airbag sensor receives a line short circuit signal 5 times in the front passenger side curtain shield squib circuit during primary check.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor


B1836/58 Center airbag sensor receives an open signal in the front passenger side curtain shield squib circuit for 2 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor


B1837/58 Center airbag sensor receives a short to ground signal in the front passenger side curtain shield squib circuit for 0.5 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor


B1838/58 center airbag sensor receives a short to B+ signal in the front passenger side curtain shield squib circuit for 0.5 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C368098E02
0.25,0.271 0.865,0.625 0.615,0.354 10 false for LHD: 1.219,2.448 1.833,2.802 0.615,0.354 10 false N13 1.208,2.615 2.781,2.938 1.573,0.323 10 false Curtain Shield Squib RH 2.354,1.156 2.969,1.51 0.615,0.354 10 false ICR+ 2.74,1.156 3.125,1.396 0.385,0.24 10 false 2 2.729,2.01 3.115,2.25 0.385,0.24 10 false 1 4.656,1.125 5.042,1.365 0.385,0.24 10 false 9 4.594,1.99 4.979,2.229 0.385,0.24 10 false 10 4.781,3.167 5.167,3.406 0.385,0.24 10 false N9 4.781,3.344 6.708,3.656 1.927,0.313 10 false Center Airbag Sensor 4.875,1.25 5.26,1.49 0.385,0.24 10 false ICP+ 2.354,2.219 2.969,2.573 0.615,0.354 10 false ICR- 2.323,5.063 2.938,5.417 0.615,0.354 10 false ICL+ 4.875,2.115 5.26,2.354 0.385,0.24 10 false ICP- 4.823,7.073 5.208,7.313 0.385,0.24 10 false M10 4.823,7.24 6.75,7.552 1.927,0.313 10 false Center Airbag Sensor 1.323,6.385 1.708,6.625 0.385,0.24 10 false M15 1.313,6.552 2.885,6.875 1.573,0.323 10 false Curtain Shield Squib LH 2.313,6.135 2.927,6.49 0.615,0.354 10 false ICL- 2.74,5.042 3.125,5.281 0.385,0.24 10 false 2 2.74,5.948 3.125,6.188 0.385,0.24 10 false 1 4.625,5.052 5.01,5.292 0.385,0.24 10 false 9 4.573,5.938 4.958,6.177 0.385,0.24 10 false 10 4.865,5.167 5.25,5.406 0.385,0.24 10 false ICP+ 4.885,6.042 5.271,6.281 0.385,0.24 10 false ICP- 0.24,4 0.854,4.354 0.615,0.354 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT PASSENGER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB)
C364214E02
4.333,0.417 4.75,0.667 0.417,0.25 4.333,0.75 4.75,1 0.417,0.25 0.979,1.365 0.979,1.135 false 4.417,2.594 4.573,2.26 true 4.792,2.594 4.646,2.406 true 1.063,0.781 1.375,0.979 0.313,0.198 10 false D 1.219,0.781 1.531,0.979 0.313,0.198 10 false C 1.573,1.271 2.74,1.646 1.167,0.375 10 false Center Airbag Sensor 0.083,1.385 1.438,1.875 1.354,0.49 10 false Front Passenger Side Curtain Shield Squib 5.208,0.094 6.281,0.333 1.073,0.24 10 false Connector C 4.406,0.792 4.719,0.99 0.313,0.198 10 false M15 4.427,1.885 4.875,2.083 0.448,0.198 10 false DLC3 5.885,1.865 6.51,2.104 0.625,0.24 10 false DTC 58 4.271,2.594 4.583,2.792 0.313,0.198 10 false CG 4.719,2.594 5.031,2.792 0.313,0.198 10 false TC 4.417,0.458 4.729,0.656 0.313,0.198 10 false N13 4.802,0.458 5.115,0.656 0.313,0.198 10 false *1 4.813,0.771 5.125,0.969 0.313,0.198 10 false *2 3.25,2.333 4.115,2.792 0.865,0.458 10 false *2: for RHD 2.333,2.333 3.198,2.792 0.865,0.458 10 false *1: for LHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger side curtain shield airbag.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the curtain shield airbag (front passenger side curtain shield squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837, B1838 or 58 is not output.


HINT:

DTCs other than DTC B1835, B1836, B1837, B1838 or 58 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE FRONT PASSENGER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the passenger side curtain shield airbag) are not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB CIRCUIT)

NG

REPAIR OR REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB CIRCUIT)
U188970E02
1.688,2.083 1.563,2.083 1.563,2.083 1.563,0.979 false 0.958,0.979 0.958,1.177 false 1.188,3.625 1.667,3.563 true 2.302,4.177 1.792,3.563 true 2.042,0.823 2.177,0.99 0.135,0.167 10 false A 1.667,0.594 1.802,0.76 0.135,0.167 10 false B 1.271,0.594 1.406,0.76 0.135,0.167 10 false C 1.052,0.594 1.188,0.76 0.135,0.167 10 false D 1.875,1.135 2.76,1.49 0.885,0.354 10 false Center Airbag Sensor 1.75,2.021 2.917,2.177 1.167,0.156 10 false Floor No. 2 Wire*1 1.75,2.333 2.563,2.49 0.813,0.156 10 false Floor Wire*2 0.146,1.167 1.292,1.865 1.146,0.698 10 false Front Passenger Side Curtain Shield Squib 1.24,2.896 2.083,3.052 0.844,0.156 10 false Connector C 2.344,3.323 2.635,3.49 0.292,0.167 10 false N13 2.344,3.74 2.667,3.906 0.323,0.167 10 false M15 2.698,3.521 2.865,3.698 0.167,0.177 10 false *1 2.708,3.906 2.875,4.083 0.167,0.177 10 false *2 0.625,3.583 1.094,3.729 0.469,0.146 10 false ICR-*1 0.625,3.792 1.094,3.938 0.469,0.146 10 false ICL-*1 2.104,4.208 2.594,4.354 0.49,0.146 10 false ICR+*1 2.104,4.427 2.604,4.573 0.5,0.146 10 false ICL+*1 0.354,4.083 1.063,4.229 0.708,0.146 10 false *1: for LHD 0.354,4.354 1.104,4.5 0.75,0.146 10 false *2: for RHD

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
N13-1 (ICR-) - Body ground Below 1 V
N13-2 (ICR+) - Body ground

for RHD:
Tester Connection Specified Condition
M15-1 (ICL-) - Body ground Below 1 V
M15-2 (ICL+) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N13-1 (ICR-) - N13-2 (ICR+) Below 1 Ω
N13-1 (ICR-) - Body ground 1 MΩ or higher
N13-2 (ICR+) - Body ground

for RHD:
Tester Connection Specified Condition
M15-1 (ICL-) - M15-2 (ICL+) Below 1 Ω
M15-1 (ICL-) - Body ground 1 MΩ or higher
M15-2 (ICL+) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N13-1 (ICR-) - N13-2 (ICR+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
M15-1 (ICL+) - M15-2 (ICL-) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE