Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1900/73  Short in Front Driver Side Pretensioner Squib Circuit  B1901/73  Open in Front Driver Side Pretensioner Squib Circuit  B1902/73  Short to GND in Front Driver Side Pretensioner Squib Circuit  B1903/73  Short to B+ in Front Driver Side Pretensioner Squib Circuit  


DESCRIPTION

The driver side front pretensioner squib circuit consists of the center airbag sensor and the driver side front seat outer belt.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front pretensioner squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1900/73 Center airbag sensor receives a line short signal 5 times in the driver side front pretensioner squib circuit during primary check.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat outer belt LH (Driver side front pretensioner squib) (for LHD)

·

Front seat outer belt RH (Driver side front pretensioner squib) (for RHD)

·

Center airbag sensor


B1901/73 Center airbag sensor receives an open signal in the driver side front pretensioner squib circuit for 2 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat outer belt LH (Driver side front pretensioner squib) (for LHD)

·

Front seat outer belt RH (Driver side front pretensioner squib) (for RHD)

·

Center airbag sensor


B1902/73 center airbag sensor receives a short to ground signal in the driver side front pretensioner squib circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat outer belt LH (Driver side front pretensioner squib) (for LHD)

·

Front seat outer belt RH (Driver side front pretensioner squib) (for RHD)

·

Center airbag sensor


B1903/73 Center airbag sensor receives a short circuit to B+ signal in the driver side front pretensioner squib circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Front seat outer belt LH (Driver side front pretensioner squib) (for LHD)

·

Front seat outer belt RH (Driver side front pretensioner squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C368098E05
0.25,0.271 0.865,0.625 0.615,0.354 10 false for LHD: 1.219,2.448 1.833,2.802 0.615,0.354 10 false M11 1.208,2.615 2.781,2.938 1.573,0.323 10 false Front Seat Outer Belt LH 2.469,1.156 3.083,1.51 0.615,0.354 10 false L+ 2.74,1.156 3.125,1.396 0.385,0.24 10 false 1 2.729,2.01 3.115,2.25 0.385,0.24 10 false 2 4.656,1.125 5.042,1.365 0.385,0.24 10 false 2 4.656,1.99 5.042,2.229 0.385,0.24 10 false 1 4.781,3.167 5.167,3.406 0.385,0.24 10 false M9 4.781,3.333 6.708,3.646 1.927,0.313 10 false Center Airbag Sensor 4.875,1.25 5.26,1.49 0.385,0.24 10 false PD+ 2.469,2.219 3.083,2.573 0.615,0.354 10 false L- 2.448,5.063 3.063,5.417 0.615,0.354 10 false R+ 4.875,2.115 5.26,2.354 0.385,0.24 10 false PD- 4.823,7.073 5.208,7.313 0.385,0.24 10 false N10 4.823,7.229 6.75,7.542 1.927,0.313 10 false Center Airbag Sensor 1.323,6.385 1.708,6.625 0.385,0.24 10 false N11 1.313,6.552 2.885,6.875 1.573,0.323 10 false Front Seat Outer Belt RH 2.448,6.135 3.063,6.49 0.615,0.354 10 false R- 2.74,5.042 3.125,5.281 0.385,0.24 10 false 1 2.74,5.948 3.125,6.188 0.385,0.24 10 false 2 4.625,5.052 5.01,5.292 0.385,0.24 10 false 2 4.625,5.938 5.01,6.177 0.385,0.24 10 false 1 4.865,5.167 5.25,5.406 0.385,0.24 10 false PD+ 4.885,6.042 5.271,6.281 0.385,0.24 10 false PD- 0.24,4 0.854,4.354 0.615,0.354 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK DRIVER SIDE FRONT SEAT OUTER BELT ASSEMBLY (DRIVER SIDE FRONT PRETENSIONER SQUIB)
C364215E02
4.167,0.417 4.583,0.667 0.417,0.25 4.167,0.75 4.583,1 0.417,0.25 0.927,1.583 0.927,1.01 false 4.396,2.469 4.552,2.094 true 4.76,2.458 4.635,2.25 true 0.979,0.646 1.292,0.844 0.313,0.198 10 false D 1.177,0.646 1.49,0.844 0.313,0.198 10 false C 1.51,1.385 2.385,1.896 0.875,0.51 10 false Center Airbag Sensor 0.219,1.615 1.417,2.094 1.198,0.479 10 false Driver Side Front Pretensioner Squib 5.083,0.156 6.052,0.406 0.969,0.25 10 false Connector C 4.26,0.792 4.573,0.99 0.313,0.198 10 false N11 4.406,1.708 4.865,1.927 0.458,0.219 10 false DLC3 5.844,1.698 6.417,1.917 0.573,0.219 10 false DTC 73 4.208,2.469 4.521,2.667 0.313,0.198 10 false CG 4.74,2.49 5.052,2.688 0.313,0.198 10 false TC 4.25,0.448 4.563,0.646 0.313,0.198 10 false M11 4.635,0.448 4.948,0.646 0.313,0.198 10 false *1 4.635,0.792 4.948,0.99 0.313,0.198 10 false *2 3.229,2.333 4.156,2.792 0.927,0.458 10 false *2: for RHD 2.302,2.333 3.229,2.792 0.927,0.458 10 false *1: for LHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the driver side front seat outer belt.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the front seat outer belt (driver side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1900, B1901, B1902, B1903 or 73 is not output.


HINT:

DTCs other than DTC B1900, B1901, B1902, B1903 or 73 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE DRIVER SIDE FRONT SEAT OUTER BELT ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the driver side front seat outer belt) is not damaged.

OK:

Lock button is not disengaged, or claw of lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)

NG

REPAIR OR REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (DRIVER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)
U189120E02
1.281,3.5 1.615,3.219 true 2.125,3.802 1.75,3.219 true 0.76,0.979 0.313,0.146 0.313,0.146 0.51,0.146 false 1.385,1.115 1.177,1.625 false 2.094,1.573 3.031,1.917 0.938,0.344 10 false Center Airbag Sensor 0.333,1.646 1.125,1.823 0.792,0.177 10 false Floor Wire*1 0.333,1.958 1.521,2.135 1.188,0.177 10 false Floor No. 2 Wire*2 0.563,0.083 2.885,0.271 2.323,0.188 10 false Driver Side Front Pretensioner Squib 1.844,0.958 1.958,1.115 0.115,0.156 10 false A 1.469,1.198 1.583,1.354 0.115,0.156 10 false B 1.083,1.198 1.219,1.354 0.135,0.156 10 false C 0.865,1.198 0.99,1.354 0.125,0.156 10 false D 1.323,2.646 2.146,2.813 0.823,0.167 10 false Connector C 2.188,3.01 2.479,3.177 0.292,0.167 10 false M11 2.188,3.354 2.479,3.521 0.292,0.167 10 false N11 2.563,3.094 2.719,3.24 0.156,0.146 10 false *1 2.552,3.448 2.708,3.594 0.156,0.146 10 false *2 0.885,3.438 1.208,3.625 0.323,0.188 10 false L+*1 0.885,3.625 1.24,3.813 0.354,0.188 10 false R+*2 2.073,3.854 2.396,4.042 0.323,0.188 10 false L-*1 2.073,4.021 2.427,4.208 0.354,0.188 10 false R-*2 0.031,3.99 0.802,4.146 0.771,0.156 10 false *1: for LHD 0.042,4.292 0.802,4.448 0.76,0.156 10 false *2: for RHD

a.

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
M11-1 (L+) - Body ground Below 1 V
M11-2 (L-) - Body ground

for RHD:
Tester Connection Specified Condition
N11-1 (R+) - Body ground Below 1 V
N11-2 (R-) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M11-1 (L+) - M11-2 (L-) Below 1 Ω
M11-1 (L+) - Body ground 1 MΩ or higher
M11-2 (L-) - Body ground

for RHD:
Tester Connection Specified Condition
N11-1 (R+) - N11-2 (R-) Below 1 Ω
N11-1 (R+) - Body ground 1 MΩ or higher
N11-2 (R-) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M11-1 (L+) - M11-2 (L-) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
N11-1 (R+) - N11-2 (R-) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE