Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1905/74  Short in Front Passenger Side Pretensioner Squib Circuit  B1906/74  Open in Front Passenger Side Pretensioner Squib Circuit  B1907/74  Short to GND in Front Passenger Side Pretensioner Squib Circuit  B1908/74  Short to B+ in Front Passenger Side Front Pretensioner Squib Circuit  


DESCRIPTION

The front passenger side front pretensioner squib circuit consists of the center airbag sensor and the front passenger side front seat outer belt.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side front pretensioner squib circuit.

DTC No. DTC Detection Condition Trouble Area
B1905/74 Center airbag sensor receives a line short signal 5 times in the front passenger side front pretensioner squib circuit during primary check.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Front seat outer belt RH (Front passenger side front pretensioner squib) (for LHD)

·

Front seat outer belt LH (Front passenger side front pretensioner squib) (for RHD)

·

Center airbag sensor


B1906/74 Center airbag sensor receives an open signal in the front passenger side front pretensioner squib circuit for 2 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Front seat outer belt RH (Front passenger side front pretensioner squib) (for LHD)

·

Front seat outer belt LH (Front passenger side front pretensioner squib) (for RHD)

·

Center airbag sensor


B1907/74 Center airbag sensor receives a short to ground signal in the front passenger side front pretensioner squib circuit for 0.5 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Front seat outer belt RH (Front passenger side front pretensioner squib) (for LHD)

·

Front seat outer belt LH (Front passenger side front pretensioner squib) (for RHD)

·

Center airbag sensor


B1908/74 Center airbag sensor receives a short to B+ signal in the front passenger side front pretensioner squib circuit for 0.5 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Front seat outer belt RH (Front passenger side front pretensioner squib) (for LHD)

·

Front seat outer belt LH (Front passenger side front pretensioner squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C368098E07
0.25,0.271 0.865,0.625 0.615,0.354 10 false for LHD: 1.219,2.448 1.833,2.802 0.615,0.354 10 false N11 1.208,2.615 2.917,2.938 1.708,0.323 10 false Front Seat Outer Belt RH 2.469,1.156 3.083,1.51 0.615,0.354 10 false R+ 2.74,1.156 3.125,1.396 0.385,0.24 10 false 1 2.729,2.01 3.115,2.25 0.385,0.24 10 false 2 4.656,1.125 5.042,1.365 0.385,0.24 10 false 4 4.656,1.99 5.042,2.229 0.385,0.24 10 false 5 4.781,3.167 5.167,3.406 0.385,0.24 10 false N9 4.781,3.333 6.708,3.646 1.927,0.313 10 false Center Airbag Sensor 4.875,1.25 5.26,1.49 0.385,0.24 10 false PP+ 2.469,2.219 3.083,2.573 0.615,0.354 10 false R- 2.448,5.063 3.063,5.417 0.615,0.354 10 false L+ 4.875,2.115 5.26,2.354 0.385,0.24 10 false PP- 4.823,7.073 5.208,7.313 0.385,0.24 10 false M10 4.823,7.229 6.75,7.542 1.927,0.313 10 false Center Airbag Sensor 1.323,6.385 1.708,6.625 0.385,0.24 10 false M11 1.313,6.552 2.885,6.875 1.573,0.323 10 false Front Seat Outer Belt LH 2.448,6.135 3.063,6.49 0.615,0.354 10 false L- 2.74,5.042 3.125,5.281 0.385,0.24 10 false 1 2.74,5.948 3.125,6.188 0.385,0.24 10 false 2 4.625,5.052 5.01,5.292 0.385,0.24 10 false 4 4.625,5.938 5.01,6.177 0.385,0.24 10 false 5 4.865,5.167 5.25,5.406 0.385,0.24 10 false PP+ 4.885,6.042 5.271,6.281 0.385,0.24 10 false PP- 0.24,4 0.854,4.354 0.615,0.354 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB)
C364216E02
4,0.417 4.417,0.667 0.417,0.25 4,0.75 4.417,1 0.417,0.25 1.083,1.51 1.083,1.115 false 4.156,2.396 4.396,2.073 true 4.635,2.406 4.469,2.219 true 1.156,0.76 1.469,0.958 0.313,0.198 10 false D 1.333,0.75 1.646,0.948 0.313,0.198 10 false C 1.677,1.25 2.573,1.75 0.896,0.5 10 false Center Airbag Sensor 0.073,1.531 1.625,2.01 1.552,0.479 10 false Front Passenger Side Front Pretensioner Squib 4.969,0.083 5.917,0.354 0.948,0.271 10 false Connector C 4.063,0.792 4.375,0.99 0.313,0.198 10 false M11 4.25,1.708 4.719,1.927 0.469,0.219 10 false DLC3 3.99,2.406 4.302,2.604 0.313,0.198 10 false CG 4.583,2.427 4.896,2.625 0.313,0.198 10 false TC 5.708,1.667 6.333,1.917 0.625,0.25 10 false DTC 74 4.073,0.458 4.385,0.656 0.313,0.198 10 false N11 4.458,0.448 4.771,0.646 0.313,0.198 10 false *1 4.469,0.792 4.781,0.99 0.313,0.198 10 false *2 3.031,2.333 3.99,2.792 0.958,0.458 10 false *2: for RHD 2.063,2.333 3.021,2.792 0.958,0.458 10 false *1: for LHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger side front seat outer belt.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the front seat outer belt (front passenger side front pretensioner squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1905, B1906, B1907, B1908 or 74 is not output.


HINT:

DTCs other than DTC B1905, B1906, B1907, B1908 or 74 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE FRONT PASSENGER SIDE FRONT SEAT OUTER BELT ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the front passenger side front seat outer belt) is not damaged.

OK:

Lock button is not disengaged, or the claw of the lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)

NG

REPAIR OR REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (FRONT PASSENGER SIDE FRONT PRETENSIONER SQUIB CIRCUIT)
U189121E02
0.771,1.406 0.771,1.604 false 1.302,3.583 1.635,3.219 true 2.271,3.833 1.75,3.208 true 1.333,1.26 1.646,0.281 1.646,0.281 1.5,0.281 false 2.156,1.552 3.073,1.906 0.917,0.354 10 false Center Airbag Sensor 1.833,1.24 1.958,1.406 0.125,0.167 10 false A 1.469,1.021 1.594,1.188 0.125,0.167 10 false B 1.083,1.021 1.208,1.188 0.125,0.167 10 false C 0.865,1.021 0.99,1.188 0.125,0.167 10 false D 1.167,2.604 2.01,2.771 0.844,0.167 10 false Connector C 0.031,0.156 1.219,0.333 1.188,0.177 10 false Floor No. 2 Wire*1 0.031,0.458 1.083,0.635 1.052,0.177 10 false Floor Wire*2 0.063,1.583 1.688,1.938 1.625,0.354 10 false Front Passenger Side Front Pretensioner Squib 2.208,3.031 2.49,3.198 0.281,0.167 10 false N11 2.198,3.396 2.5,3.563 0.302,0.167 10 false M11 2.563,3.125 2.708,3.302 0.146,0.177 10 false *1 2.563,3.49 2.729,3.667 0.167,0.177 10 false *2 0.885,3.49 1.25,3.635 0.365,0.146 10 false R+*1 0.885,3.688 1.208,3.833 0.323,0.146 10 false L+*2 2.167,3.885 2.531,4.031 0.365,0.146 10 false R-*1 2.167,4.083 2.49,4.229 0.323,0.146 10 false L-*2 0.052,4.01 0.771,4.177 0.719,0.167 10 false *1: for LHD 0.052,4.323 0.813,4.49 0.76,0.167 10 false *2: for RHD

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
N11-1 (R+) - Body ground Below 1 V
N11-2 (R-) - Body ground

for RHD:
Tester Connection Specified Condition
M11-1 (L+) - Body ground Below 1 V
M11-2 (L-) - Body ground



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N11-1 (R+) - N11-2 (R-) Below 1 Ω
N11-1 (R+) - Body ground 1 MΩ or higher
N11-2 (R-) - Body ground

for RHD:
Tester Connection Specified Condition
M11-1 (L+) - M11-2 (L-) Below 1 Ω
M11-1 (L+) - Body ground 1 MΩ or higher
M11-2 (L-) - Body ground



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N11-1 (R+) - N11-2 (R-) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
M11-1 (L+) - M11-2 (L-) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE