Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost Communication with Driver Side - Side Airbag Sensor Assembly  


DESCRIPTION

The driver side - side airbag sensor (for front side) consists of parts including the diagnostic circuit and the lateral deceleration sensor.

When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.

DTC B1622/81 is set when a malfunction is detected in the driver side - side airbag sensor (for front side) circuit.

DTC No. DTC Detection Condition Trouble Area
B1622/81 When one of following conditions is met:
·

Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in driver side - side airbag sensor (for front side) circuit for 2 seconds.

·

Driver side - side airbag (for front side) sensor malfunction

·

Center airbag sensor malfunction


·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Side airbag sensor LH (for front side) (for LHD)

·

Side airbag sensor RH (for front side) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C140726E05
0.198,0.479 0.958,0.729 0.76,0.25 10 false for LHD: 0.177,4.667 0.875,4.885 0.698,0.219 10 false for RHD: 0.125,4.021 1.531,4.198 1.406,0.177 10 false Rear Airbag Sensor LH 2.292,3.885 3.771,4.281 1.479,0.396 10 false Side Airbag Sensor LH (for Rear Side) 4.719,3.885 5.698,4.469 0.979,0.583 10 false Rear Floor Airbag Sensor 6.031,4.021 6.969,4.438 0.938,0.417 10 false Center Airbag Sensor 0.76,1.208 1.188,1.396 0.427,0.188 10 false BCL+ 3.01,1.188 3.448,1.385 0.438,0.198 10 false BCL+ 0.771,1.698 1.167,1.917 0.396,0.219 10 false BCL- 3.021,1.688 3.438,1.917 0.417,0.229 10 false BCL- 0.75,2.885 1.208,3.115 0.458,0.229 10 false BDL+ 2.51,2.875 2.948,3.083 0.438,0.208 10 false BDL+ 1.698,2.875 2.01,3.083 0.313,0.208 10 false LM3 0.771,3.365 1.208,3.583 0.438,0.219 10 false BDL- 2.521,3.365 3.01,3.583 0.49,0.219 10 false BDL- 3.563,1.198 3.99,1.396 0.427,0.198 10 false BBL+ 3.625,1.688 3.99,1.885 0.365,0.198 10 false BBL- 3.094,2.865 3.521,3.083 0.427,0.219 10 false BEL+ 4.854,2.875 5.323,3.063 0.469,0.188 10 false BEL+ 3.115,3.375 3.521,3.552 0.406,0.177 10 false BEL- 4.854,3.375 5.219,3.552 0.365,0.177 10 false BEL- 6.063,1.198 6.51,1.375 0.448,0.177 10 false BBD+ 5.844,1.073 6.031,1.281 0.188,0.208 10 false 8 5.76,1.583 5.979,1.792 0.219,0.208 10 false 15 4.063,1.094 4.25,1.302 0.188,0.208 10 false 4 4.052,1.583 4.271,1.792 0.219,0.208 10 false 3 1.26,1.083 1.448,1.292 0.188,0.208 10 false 4 1.25,1.573 1.469,1.781 0.219,0.208 10 false 3 1.24,2.75 1.427,2.958 0.188,0.208 10 false 1 1.792,2.677 1.979,2.885 0.188,0.208 10 false 1 1.698,3.365 2.01,3.573 0.313,0.208 10 false LM3 1.792,3.167 1.979,3.375 0.188,0.208 10 false 2 3.969,2.865 4.281,3.073 0.313,0.208 10 false LM3 4.052,2.667 4.24,2.875 0.188,0.208 10 false 3 3.958,3.365 4.271,3.573 0.313,0.208 10 false LM3 4.052,3.167 4.24,3.375 0.188,0.208 10 false 4 1.698,7.063 2.01,7.271 0.313,0.208 10 false KN3 1.792,6.854 1.979,7.063 0.188,0.208 10 false 1 1.698,7.552 2.01,7.76 0.313,0.208 10 false KN3 1.792,7.365 1.979,7.573 0.188,0.208 10 false 2 3.76,7.063 4.073,7.271 0.313,0.208 10 false KN3 3.854,6.854 4.042,7.063 0.188,0.208 10 false 3 3.76,7.552 4.073,7.76 0.313,0.208 10 false KN3 3.854,7.354 4.042,7.563 0.188,0.208 10 false 4 4.292,7.063 4.604,7.271 0.313,0.208 10 false NM1 4.385,6.865 4.573,7.073 0.188,0.208 10 false 2 4.292,7.552 4.604,7.76 0.313,0.208 10 false NM1 4.385,7.354 4.573,7.563 0.188,0.208 10 false 1 1.25,3.24 1.469,3.448 0.219,0.208 10 false 2 3.542,2.771 3.729,2.979 0.188,0.208 10 false 1 3.552,3.25 3.771,3.458 0.219,0.208 10 false 2 4.646,2.771 4.833,2.979 0.188,0.208 10 false 2 4.646,3.26 4.865,3.469 0.219,0.208 10 false 1 2.313,2.76 2.5,2.969 0.188,0.208 10 false 4 2.302,3.25 2.521,3.458 0.219,0.208 10 false 3 2.792,1.083 2.979,1.292 0.188,0.208 10 false 1 2.781,1.583 3,1.792 0.219,0.208 10 false 2 6.063,1.698 6.479,1.875 0.417,0.177 10 false BBD- 2.271,2.177 4.656,2.354 2.385,0.177 10 false Side Airbag Sensor RH (for Front Side) 0.156,8.198 1.688,8.438 1.531,0.24 10 false Rear Airbag Sensor RH 2.271,8.042 3.781,8.406 1.51,0.365 10 false Side Airbag Sensor RH (for Rear Side) 4.792,8.073 5.75,8.438 0.958,0.365 10 false Center Floor Airbag Sensor 6.01,8.208 6.885,8.573 0.875,0.365 10 false Center Airbag Sensor 0.74,5.375 1.167,5.563 0.427,0.188 10 false BCR+ 3.01,5.375 3.448,5.573 0.438,0.198 10 false BCR+ 0.74,5.865 1.135,6.083 0.396,0.219 10 false BCR- 3.01,5.865 3.427,6.094 0.417,0.229 10 false BCR- 0.74,7.042 1.198,7.271 0.458,0.229 10 false BDR+ 2.51,7.063 2.948,7.271 0.438,0.208 10 false BDR+ 0.74,7.573 1.177,7.792 0.438,0.219 10 false BDR- 2.521,7.542 3.01,7.76 0.49,0.219 10 false BDR- 3.542,5.375 3.969,5.573 0.427,0.198 10 false BBR+ 3.594,5.865 3.958,6.063 0.365,0.198 10 false BBR- 3.073,7.052 3.5,7.271 0.427,0.219 10 false BER+ 4.865,7.052 5.333,7.24 0.469,0.188 10 false BER+ 3.073,7.542 3.479,7.719 0.406,0.177 10 false BER- 4.865,7.552 5.229,7.729 0.365,0.177 10 false BER- 6.063,5.385 6.51,5.563 0.448,0.177 10 false BBD+ 5.833,5.271 6.021,5.479 0.188,0.208 10 false 8 5.76,5.771 5.979,5.979 0.219,0.208 10 false 15 4.052,5.271 4.24,5.479 0.188,0.208 10 false 4 4.052,5.771 4.271,5.979 0.219,0.208 10 false 3 1.25,5.24 1.438,5.448 0.188,0.208 10 false 4 1.25,5.75 1.469,5.958 0.219,0.208 10 false 3 1.25,6.917 1.438,7.125 0.188,0.208 10 false 1 1.25,7.417 1.469,7.625 0.219,0.208 10 false 2 3.552,6.948 3.74,7.156 0.188,0.208 10 false 1 3.552,7.448 3.771,7.656 0.219,0.208 10 false 2 4.656,6.948 4.844,7.156 0.188,0.208 10 false 2 4.656,7.438 4.875,7.646 0.219,0.208 10 false 1 2.313,6.948 2.5,7.156 0.188,0.208 10 false 4 2.313,7.438 2.531,7.646 0.219,0.208 10 false 3 2.792,5.25 2.979,5.458 0.188,0.208 10 false 1 2.792,5.76 3.01,5.969 0.219,0.208 10 false 2 6.063,5.875 6.479,6.052 0.417,0.177 10 false BBD- 2.354,6.375 4.781,6.594 2.427,0.219 10 false Side Airbag Sensor LH (for Front Side) 0.125,3.833 0.583,4.031 0.458,0.198 10 false M20 2.302,3.698 2.76,3.896 0.458,0.198 10 false L10 4.719,3.698 5.177,3.896 0.458,0.198 10 false M21 6.021,3.833 6.333,4.031 0.313,0.198 10 false M9 2.281,2 2.74,2.198 0.458,0.198 10 false M16 2.365,6.188 2.823,6.385 0.458,0.198 10 false N12 6.021,8.042 6.479,8.24 0.458,0.198 10 false N10 4.802,7.906 5.115,8.104 0.313,0.198 10 false N4 2.281,7.865 2.74,8.063 0.458,0.198 10 false K10 0.156,8.021 0.615,8.219 0.458,0.198 10 false N23

PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


b.

Turn the ignition switch off.


c.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


d.

Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1623 is output. A
DTC B1628 is output. B

HINT:

DTCs other than DTC B1623 and B1628 may be output at this time, but they are not related to this check.




A

2.CHECK CONNECTION OF CONNECTOR

B

Go to DTC B1627/81

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the driver side - side airbag sensor (for front side).

OK:

Connectors are properly connected.




OK

3.CHECK FLOOR WIRE (OPEN)

NG

CONNECT CONNECTOR

3.CHECK FLOOR WIRE (OPEN)
C366261E01
0.083,3 0.5,3.25 0.417,0.25 0.083,2.5 0.5,2.75 0.417,0.25 1.583,3 2,3.25 0.417,0.25 1.583,2.5 2,2.75 0.417,0.25 1.917,1.49 1.729,1.49 1.729,1.49 1.625,0.75 false 0.656,3.625 0.927,3.281 true 1.125,3.635 1.021,3.271 true 2.021,3.563 2.302,3.281 true 2.531,3.115 2.906,2.896 true 2.219,3.917 2.354,3.51 false 2.167,0.615 2.479,0.813 0.313,0.198 10 false A 1.75,0.365 2.063,0.563 0.313,0.198 10 false B 1.417,0.365 1.729,0.563 0.313,0.198 10 false C 0.99,0.604 1.302,0.802 0.313,0.198 10 false D 0.344,1.219 1.396,1.885 1.052,0.667 10 false Driver Side - Side Airbag Sensor (for Front Side) 1.969,1.396 3.427,1.698 1.458,0.302 10 false Floor Wire*1 2.5,0.188 2.958,0.833 0.458,0.646 10 false Center Airbag Sensor 0.521,2.25 1.385,2.458 0.865,0.208 10 false Connector C 2.104,2.229 3,2.479 0.896,0.25 10 false Connector B 0.385,2.771 0.698,2.969 0.313,0.198 10 false *1 0.167,3.042 0.479,3.24 0.313,0.198 10 false N12 1.688,2.542 2,2.74 0.313,0.198 10 false M9 1.677,3.042 1.99,3.24 0.313,0.198 10 false N10 0.281,3.635 0.833,3.865 0.552,0.229 10 false BBL-*1 2.948,2.813 3.385,3.021 0.438,0.208 10 false BBD+ 2.083,3.948 2.969,4.188 0.885,0.24 10 false Service Wire 0.344,4.323 1.198,4.667 0.854,0.344 10 false *1: for LHD 1.969,1.677 3.427,1.979 1.458,0.302 10 false Floor No. 2 Wire*2 0.156,2.531 0.469,2.729 0.313,0.198 10 false M16 0.333,3.281 0.646,3.479 0.313,0.198 10 false *2 1.865,2.771 2.177,2.969 0.313,0.198 10 false *1 1.854,3.271 2.167,3.469 0.313,0.198 10 false *2 1.719,3.563 2.156,3.771 0.438,0.208 10 false BBD- 0.281,3.813 0.833,4.042 0.552,0.229 10 false BBR-*2 0.99,3.646 1.542,3.875 0.552,0.229 10 false BBL+*1 0.99,3.813 1.542,4.042 0.552,0.229 10 false BBR+*2 1.188,4.323 2.042,4.667 0.854,0.344 10 false *2: for RHD

a.

Disconnect the connectors from the center airbag sensor and the driver side - side airbag sensor (for front side).


b.

for LHD:

Using a service wire, connect terminals M9-8 (BBD+) and M9-15 (BBD-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting them.



c.

for RHD:

Using a service wire, connect terminals N10-8 (BBD+) and N10-15 (BBD-) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting them.



d.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M16-3 (BBL-) - M16-4 (BBL+) Below 1 Ω

for RHD:
Tester Connection Specified Condition
N12-3 (BBR-) - N12-4 (BBR+) Below 1 Ω




OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPAIR OR REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
U189124E02
1.635,0.969 1.719,1.698 1.719,1.698 1.771,1.698 false 1.583,4.042 1.677,3.656 false 2.104,3.927 1.771,3.667 false 2.458,0.385 2.927,0.969 0.469,0.583 10 false Center Airbag Sensor 0.156,1.427 1.281,2.333 1.125,0.906 10 false Driver Side - Side Airbag Sensor (for Front Side) 2.198,0.823 2.323,0.969 0.125,0.146 10 false A 1.771,0.594 1.896,0.74 0.125,0.146 10 false B 1.396,0.604 1.521,0.75 0.125,0.146 10 false C 1.031,0.823 1.156,0.969 0.125,0.146 10 false D 1.875,1.604 2.708,1.781 0.833,0.177 10 false Floor Wire*1 1.875,1.927 3.042,2.104 1.167,0.177 10 false Floor No. 2 Wire*2 1.219,2.542 2.083,2.729 0.865,0.188 10 false Connector C 0.146,3.969 0.896,4.156 0.75,0.188 10 false *1: for LHD 0.146,4.271 0.896,4.458 0.75,0.188 10 false *2: for RHD 0.677,3.188 0.969,3.354 0.292,0.167 10 false M16 0.688,3.49 0.979,3.656 0.292,0.167 10 false N12 1.083,3.177 1.25,3.344 0.167,0.167 10 false *1 1.094,3.51 1.26,3.677 0.167,0.167 10 false *2 1.385,4.063 1.865,4.229 0.479,0.167 10 false BBL-*1 1.385,4.219 1.927,4.385 0.542,0.167 10 false BBR-*2 2.146,3.885 2.729,4.052 0.583,0.167 10 false BBL+*1 2.156,4.052 2.781,4.219 0.625,0.167 10 false BBR+*2

a.

Disconnect the service wire from connector B.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M16-3 (BBL-) - M16-4 (BBL+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
N12-3 (BBR-) - N12-4 (BBR+) 1 MΩ or higher




OK

5.CHECK FLOOR WIRE (TO B+)

NG

REPAIR OR REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (TO B+)
U189124E02
1.635,0.969 1.719,1.698 1.719,1.698 1.771,1.698 false 1.583,4.042 1.677,3.656 false 2.104,3.927 1.771,3.667 false 2.458,0.385 2.927,0.969 0.469,0.583 10 false Center Airbag Sensor 0.156,1.427 1.281,2.333 1.125,0.906 10 false Driver Side - Side Airbag Sensor (for Front Side) 2.198,0.823 2.323,0.969 0.125,0.146 10 false A 1.771,0.594 1.896,0.74 0.125,0.146 10 false B 1.396,0.604 1.521,0.75 0.125,0.146 10 false C 1.031,0.823 1.156,0.969 0.125,0.146 10 false D 1.875,1.604 2.708,1.781 0.833,0.177 10 false Floor Wire*1 1.875,1.927 3.042,2.104 1.167,0.177 10 false Floor No. 2 Wire*2 1.219,2.542 2.083,2.729 0.865,0.188 10 false Connector C 0.146,3.969 0.896,4.156 0.75,0.188 10 false *1: for LHD 0.146,4.271 0.896,4.458 0.75,0.188 10 false *2: for RHD 0.677,3.188 0.969,3.354 0.292,0.167 10 false M16 0.688,3.49 0.979,3.656 0.292,0.167 10 false N12 1.083,3.177 1.25,3.344 0.167,0.167 10 false *1 1.094,3.51 1.26,3.677 0.167,0.167 10 false *2 1.385,4.063 1.865,4.229 0.479,0.167 10 false BBL-*1 1.385,4.219 1.927,4.385 0.542,0.167 10 false BBR-*2 2.146,3.885 2.729,4.052 0.583,0.167 10 false BBL+*1 2.156,4.052 2.781,4.219 0.625,0.167 10 false BBR+*2

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
M16-3 (BBL-) - Body ground Below 1 V
M16-4 (BBL+) - Body ground

for RHD:
Tester Connection Specified Condition
N12-3 (BBR-) - Body ground Below 1 V
N12-4 (BBR+) - Body ground




OK

6.CHECK FLOOR WIRE (TO GROUND)

NG

REPAIR OR REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (TO GROUND)
U189124E02
1.635,0.969 1.719,1.698 1.719,1.698 1.771,1.698 false 1.583,4.042 1.677,3.656 false 2.104,3.927 1.771,3.667 false 2.458,0.385 2.927,0.969 0.469,0.583 10 false Center Airbag Sensor 0.156,1.427 1.281,2.333 1.125,0.906 10 false Driver Side - Side Airbag Sensor (for Front Side) 2.198,0.823 2.323,0.969 0.125,0.146 10 false A 1.771,0.594 1.896,0.74 0.125,0.146 10 false B 1.396,0.604 1.521,0.75 0.125,0.146 10 false C 1.031,0.823 1.156,0.969 0.125,0.146 10 false D 1.875,1.604 2.708,1.781 0.833,0.177 10 false Floor Wire*1 1.875,1.927 3.042,2.104 1.167,0.177 10 false Floor No. 2 Wire*2 1.219,2.542 2.083,2.729 0.865,0.188 10 false Connector C 0.146,3.969 0.896,4.156 0.75,0.188 10 false *1: for LHD 0.146,4.271 0.896,4.458 0.75,0.188 10 false *2: for RHD 0.677,3.188 0.969,3.354 0.292,0.167 10 false M16 0.688,3.49 0.979,3.656 0.292,0.167 10 false N12 1.083,3.177 1.25,3.344 0.167,0.167 10 false *1 1.094,3.51 1.26,3.677 0.167,0.167 10 false *2 1.385,4.063 1.865,4.229 0.479,0.167 10 false BBL-*1 1.385,4.219 1.927,4.385 0.542,0.167 10 false BBR-*2 2.146,3.885 2.729,4.052 0.583,0.167 10 false BBL+*1 2.156,4.052 2.781,4.219 0.625,0.167 10 false BBR+*2

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M16-3 (BBL-) - Body ground 1 MΩ or higher
M16-4 (BBL+) - Body ground

for RHD:
Tester Connection Specified Condition
N12-3 (BBR-) - Body ground 1 MΩ or higher
N12-4 (BBR+) - Body ground




OK

7.CHECK DRIVER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Front Side)

NG

REPAIR OR REPLACE FLOOR WIRE

7.CHECK DRIVER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Front Side)
C131087E06
0.365,3.99 0.563,3.552 true 0.813,3.979 0.646,3.74 true 2.208,1.781 3.115,2.104 0.906,0.323 10 false Center Airbag Sensor 0.083,1.688 1.531,2.229 1.448,0.542 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.417,3.104 0.854,3.271 0.438,0.167 10 false DLC3 0.125,3.99 0.375,4.135 0.25,0.146 10 false CG 0.802,3.99 1.052,4.135 0.25,0.146 10 false TC 2.125,2.479 2.646,2.656 0.521,0.177 10 false DTC 81 2.125,3.615 2.646,3.792 0.521,0.177 10 false DTC 82

a.

Connect the connectors to the center airbag sensor.


b.

Interchange the driver side - side airbag sensor (for front side) with the front passenger side - side airbag sensor (for front side) and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1622/81 and B1627/82 are not output A
DTC B1627/82 is output B
DTC B1622/81 is output C

HINT:

DTCs other than DTC B1622/81 and B1627/82 may be output at this time, but they are not related to this check.




A

USE SIMULATION METHOD TO CHECK

B

REPLACE DRIVER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Driver Side)

C

REPLACE CENTER AIRBAG SENSOR ASSEMBLY