The rear airbag sensor (for driver side) consists of parts including the diagnostic circuit and the lateral deceleration sensor.
When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1632/81 is set when a malfunction is detected in rear airbag sensor (for driver side) circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1632/81 | When one of following conditions is met:
·
Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in driver side - side airbag sensor (for front side) circuit for 2 seconds. ·
Rear airbag sensor (for driver side) malfunction ·
Center airbag sensor malfunction |
·
Floor wire (for LHD) ·
Floor No. 2 wire (for RHD) ·
Rear airbag sensor LH (for LHD) ·
Rear airbag sensor RH (for RHD) ·
Center airbag sensor |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1633 is output. | A |
| DTC B1638 is output. | B |
DTCs other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.
A
B
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor (for driver side) and the driver side - side airbag sensor (for front side).
Connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and the driver side - side airbag sensor (for front side).
for LHD:
Using a service wire, connect terminals M9-8 (BBD+) and M9-15 (BBD-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
for RHD:
Using a service wire, connect terminals N10-8 (BBD+) and N10-15 (BBD-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - M16-4 (BBL+) | Below 1 Ω |
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBR-) - N12-4 (BBR+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - M16-4 (BBL+) | Below 1 Ω |
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBR-) - N12-4 (BBR+) | Below 1 Ω |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - Body ground | Below 1 V |
| M16-4 (BBL+) - Body ground |
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBL+) - Body ground | Below 1 V |
| N12-4 (BBL-) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - Body ground | 1 MΩ or higher |
| M16-4 (BBL+) - Body ground |
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBL+) - Body ground | 1 MΩ or higher |
| N12-4 (BBL-) - Body ground |
OK
NG
Disconnect the connectors from the driver side - side airbag sensor (for front side) and the rear airbag sensor (for driver side).
for LHD:
Using a service wire, connect terminals M16-1 (BCL+) and M16-2 (BCL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
for RHD:
Using a service wire, connect terminals N12-1 (BCR+) and N12-2 (BCR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - M20-4 (BCL+) | Below 1 Ω |
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - N23-4 (BCR+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - M20-4 (BCL+) | 1 MΩ or higher |
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - N23-4 (BCR+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - Body ground | Below 1 V |
| M20-4 (BCL+) - Body ground |
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - Body ground | Below 1 V |
| N23-4 (BCR+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - Body ground | 1 MΩ or higher |
| M20-4 (BCL+) - Body ground |
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - Body ground | 1 MΩ or higher |
| N23-4 (BCR+) - Body ground |
OK
NG
Connect the connectors to the center airbag sensor.
Interchange the driver side - side airbag sensor (for front side) with the front passenger side - side airbag sensor (for front side) and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1632/81 and B1637/82 are not output | A |
| DTC B1632/81 is output | B |
| DTC B1637/82 is output | C |
DTCs other than DTC B1632/81 and B1637/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor (for driver side) with the rear airbag sensor (for front passenger side) and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1632/81 and B1637/82 are not output | A |
| DTC B1632/81 is output | B |
| DTC B1637/81 is output | C |
DTCs other than DTC B1632/81 and B1637/82 may be output at this time, but they are not related to this check.
A
B
C