When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1648/82 is set when a malfunction is detected in the side airbag sensor LH/RH (for front side) circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1648/82 | When one of following conditions is met:
·
Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in side airbag sensor LH/RH (for front side) circuit for 2 seconds. ·
Side airbag sensor LH/RH (for front side) malfunction ·
Rear airbag sensor LH/RH malfunction ·
Center floor airbag sensor malfunction ·
Rear floor airbag sensor malfunction ·
Side airbag sensor LH/RH (for rear side) malfunction ·
Center airbag sensor malfunction |
·
Floor wire ·
Floor No. 2 wire ·
Door wire LH/RH ·
Side airbag sensor LH/RH (for front side) ·
Rear airbag sensor LH/RH ·
Side airbag sensor LH/RH (for rear side) ·
Center floor airbag sensor ·
Rear floor airbag sensor ·
Center airbag sensor |
| Result | Proceed to |
|---|---|
| Steering is LHD side | A |
| Steering is RHD side | B |
A
B
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1642/81 is not output.
DTC B1647/82 is not output.
DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor RH, side airbag sensor RH (for front side), side airbag sensor RH (for rear side), and the center floor airbag sensor.
Connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and the side airbag sensor RH (for front side).
Using a service wire, connect terminals N9-8 (BBP+) and N9-11 (BBP-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBR-) - N12-4 (BBR+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBR-) - N12-4 (BBR+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBR-) - Body ground | Below 1 V |
| N12-4 (BBR+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N12-3 (BBR-) - Body ground | 1 MΩ or higher |
| N12-4 (BBR+) - Body ground |
OK
NG
Disconnect the connectors from the side airbag sensor RH (for front side) and the rear airbag sensor RH.
Using a service wire, connect terminals N12-1 (BCR+) and N12-2 (BCR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - N23-4 (BCR+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - N23-4 (BCR+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - Body ground | Below 1 V |
| N23-4 (BCR+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| N23-3 (BCR-) - Body ground | 1 MΩ or higher |
| N23-4 (BCR+) - Body ground |
OK
NG
Disconnect the connectors from the rear airbag sensor RH and the side airbag sensor RH (for rear side).
Using a service wire, connect terminals N23-1 (BDR+) and N23-2 (BDR-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - K10-4 (BDR+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - K10-4 (BDR+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - Body ground | Below 1 V |
| K10-4 (BDR+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - Body ground | 1 MΩ or higher |
| K10-4 (BDR+) - Body ground |
OK
NG
Disconnect the connectors from the side airbag sensor RH (for rear side) and the center floor airbag sensor.
Using a service wire, connect terminals K10-1 (BER+) and K10-2 (BER-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M4-1 (BER-) - M4-2 (BER+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M4-1 (BER-) - M4-2 (BER+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M4-1 (BER-) - Body ground | Below 1 V |
| M4-2 (BER+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M4-1 (BER-) - Body ground | 1 MΩ or higher |
| M4-2 (BER+) - Body ground |
OK
NG
Connect the connectors to the center airbag sensor.
Interchange the side airbag sensor RH (for front side) with the side airbag sensor LH (for front side) and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the side airbag sensor RH (for rear side) with the side airbag sensor LH (for rear side) and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the center floor airbag sensor with the rear floor airbag sensor and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Disconnect the door wire connector from the floor No. 2 wire.
Using a service wire, connect terminals KN3-1 and KN3-2 of connector D.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - K10-4 (BDR+) | Below 1 Ω |
OK
NG
Disconnect the door wire connector from the floor No. 2 wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - K10-4 (BDR+) | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the door wire connector from the floor No. 2 wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - Body ground | Below 1 V |
| K10-4 (BDR+) - Body ground |
OK
NG
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| K10-3 (BDR-) - Body ground | 1 MΩ or higher |
| K10-4 (BDR+) - Body ground |
OK
NG
Disconnect the door wire connector from the floor No. 2 wire.
Using a service wire, connect terminals K10-1 (BER+) and K10-2 (BER-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| KN3-3 - KN3-4 | Below 1 Ω |
NG
OK
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| KN3-3 - KN3-4 | 1 MΩ or higher |
NG
OK
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the door wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| KN3-3 - Body ground | Below 1 V |
| KN3-4 - Body ground |
NG
OK
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| KN3-3 - Body ground | 1 MΩ or higher |
| KN3-4 - Body ground |
NG
OK
Disconnect the floor wire connector from the floor No. 2 wire.
Using a service wire, connect terminals KN3-3 and KN3-4 of connector D.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| NM1-1 - NM1-2 | Below 1 Ω |
OK
NG
Disconnect the floor wire connector from the floor No. 2 wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| NM1-1 - NM1-2 | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the floor wire connector from the floor No. 2 wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| NM1-1 - Body ground | Below 1 V |
| NM1-2 - Body ground |
OK
NG
Disconnect the floor wire connector from the floor No. 2 wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| NM1-1 - Body ground | 1 MΩ or higher |
| NM1-2 - Body ground |
OK
NG
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1642/81 is not output.
DTC B1647/82 is not output.
DTCs other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor LH, side airbag sensor LH (for front side), side airbag sensor LH (for rear side), and the rear airbag sensor.
Connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor and the side airbag sensor LH (for front side).
Using a service wire, connect terminals M10-8 (BBP+) and M10-11 (BBP-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - M16-4 (BBL+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - M16-4 (BBL+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - Body ground | Below 1 V |
| M16-4 (BBL+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M16-3 (BBL-) - Body ground | 1 MΩ or higher |
| M16-4 (BBRL+) - Body ground |
OK
NG
Disconnect the connectors from the side airbag sensor LH (for front side) and the rear airbag sensor LH.
Using a service wire, connect terminals M16-1 (BCL+) and M16-2 (BCL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - M20-4 (BCL+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - M20-4 (BCL+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - Body ground | Below 1 V |
| M20-4 (BCL+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M20-3 (BCL-) - Body ground | 1 MΩ or higher |
| M20-4 (BCL+) - Body ground |
OK
NG
Disconnect the connectors from the rear airbag sensor LH and the side airbag sensor LH (for rear side).
Using a service wire, connect terminals M20-1 (BDL+) and M20-2 (BDL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - L10-4 (BDL+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - L10-4 (BDL+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - Body ground | Below 1 V |
| L10-4 (BDL+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - Body ground | 1 MΩ or higher |
| L10-4 (BDL+) - Body ground |
OK
NG
Disconnect the connectors from the side airbag sensor LH (for rear side) and the rear floor airbag sensor.
Using a service wire, connect terminals L10-1 (BEL+) and L10-2 (BEL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M21-1 (BEL-) - M21-2 (BEL+) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M21-1 (BEL-) - M21-2 (BEL+) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M21-1 (BEL-) - Body ground | Below 1 V |
| M21-2 (BEL+) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| M21-1 (BEL-) - Body ground | 1 MΩ or higher |
| M21-2 (BEL+) - Body ground |
OK
NG
Connect the connectors to the center airbag sensor.
Interchange the side airbag sensor LH (for front side) with the side airbag sensor RH (for front side) and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear airbag sensor RH with the rear airbag sensor LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the side airbag sensor LH (for rear side) with the side airbag sensor RH (for rear side) and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the rear floor airbag sensor with the center floor airbag sensor and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1643/81 and B1648/82 are not output | A |
| DTC B1648/82 is output | B |
| DTC B1643/81 is output | C |
DTCs other than DTC B1643/81 and B1648/82 may be output at this time, but they are not related to this check.
A
B
C
Disconnect the door wire connector from the floor wire.
Using a service wire, connect terminals LM3-1 and LM3-2 of connector D.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - L10-4 (BDL+) | Below 1 Ω |
OK
NG
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - L10-4 (BDL+) | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the door wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - Body ground | Below 1 V |
| L10-4 (BDL+) - Body ground |
OK
NG
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| L10-3 (BDL-) - Body ground | 1 MΩ or higher |
| L10-4 (BDL+) - Body ground |
OK
NG
Disconnect the door wire connector from the floor wire.
Using a service wire, connect terminals L10-1 (BEL+) and L10-2 (BEL-) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| LM3-3 - LM3-4 | Below 1 Ω |
OK
NG
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| LM3-3 - LM3-4 | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the door wire connector from the floor wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| LM3-3 - Body ground | Below 1 V |
| LM3-4 - Body ground |
OK
NG
Disconnect the door wire connector from the floor wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| LM3-3 - Body ground | 1 MΩ or higher |
| LM3-4 - Body ground |
OK
NG