Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1602/83  Lost Communication with Front Satellite Sensor Bus RH  B1612/83  Lost Communication with Front Airbag Sensor RH  


DESCRIPTION

The front airbag sensor RH consists of the diagnostic circuit and the frontal deceleration sensor.

If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.

DTC B1602/83 or B1612/83 is recorded when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area
B1602/83
B1612/83
When one of following conditions is met:
·

Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in front airbag sensor RH circuit for 2 seconds

·

Front airbag sensor RH malfunction

·

Center airbag sensor malfunction


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Center airbag sensor



WIRING DIAGRAM

C367977E01
1.448,1.938 1.906,2.135 0.458,0.198 10 false +SR 1.917,1.844 2.073,2.042 0.156,0.198 10 false 2 3.385,1.958 3.844,2.156 0.458,0.198 10 false AG7 3.49,1.75 3.646,1.948 0.156,0.198 10 false 1 5.104,1.833 5.417,2.031 0.313,0.198 10 false 29 5.448,1.969 5.906,2.167 0.458,0.198 10 false +SR 1.51,3.688 1.969,3.885 0.458,0.198 10 false -SR 1.896,3.583 2.052,3.781 0.156,0.198 10 false 1 3.385,3.688 3.844,3.885 0.458,0.198 10 false AG7 3.5,3.479 3.656,3.677 0.156,0.198 10 false 2 5.104,3.563 5.417,3.76 0.313,0.198 10 false 27 5.438,3.698 5.896,3.896 0.458,0.198 10 false -SR 0.26,4.979 0.719,5.177 0.458,0.198 10 false A18 0.26,5.156 1.802,5.375 1.542,0.219 10 false Front Airbag Sensor RH 5.448,4.99 5.906,5.188 0.458,0.198 10 false G19 5.448,5.167 6.813,5.375 1.365,0.208 10 false Center Airbag Sensor

PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


b.

Turn the ignition switch off.


c.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


d.

Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1603/83 is output A
DTC B1608/84 is output B

HINT:

DTCs other than DTC B1603/83 and B1608/84 may be output at this time, but they are not related to this check.




A

2.CHECK CONNECTION OF CONNECTOR

B

Go to DTC B1607/84

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH (for front side).

OK:

Connectors are properly connected.




OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)

NG

CONNECT CONNECTOR

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (OPEN)
U189104E02
2.26,3.802 2.26,3.927 false 0.552,3.573 0.792,3.156 false 1.198,3.583 0.969,3.156 false 1.823,3.594 2.125,3.219 false 2.823,3.573 2.344,3.208 false 2.25,1.479 3.146,1.833 0.896,0.354 10 false Center Airbag Sensor 2.448,0.469 2.573,0.635 0.125,0.167 10 false A 2,0.26 2.125,0.427 0.125,0.167 10 false B 1.625,0.271 1.75,0.438 0.125,0.167 10 false C 1.51,0.271 1.635,0.438 0.125,0.167 10 false D 1.135,0.271 1.26,0.438 0.125,0.167 10 false E 0.719,0.479 0.844,0.646 0.125,0.167 10 false F 0.188,0.99 0.979,1.313 0.792,0.323 10 false Front Airbag Sensor RH 0.458,2.313 1.271,2.469 0.813,0.156 10 false Connector E 2.021,2.313 2.833,2.469 0.813,0.156 10 false Connector B 2.708,3.583 2.979,3.781 0.271,0.198 10 false -SR 0.323,3.594 0.594,3.792 0.271,0.198 10 false -SR 1.656,3.594 1.979,3.792 0.323,0.198 10 false +SR 1.208,3.573 1.531,3.771 0.323,0.198 10 false +SR 1.823,3.948 2.667,4.125 0.844,0.177 10 false Service Wire 1.552,3.021 1.844,3.167 0.292,0.146 10 false G19 0.115,3.01 0.406,3.156 0.292,0.146 10 false A18

a.

Disconnect the connectors from the center airbag sensor and the front airbag sensor RH.


b.

Using a service wire, connect terminals G19-29 (+SR) and G19-27 (-SR) of connector B.

NOTICE:

Do not forcibly insert a service wire into the terminals of the connector when connecting them.



c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A18-1 (-SR) - A18-2 (+SR) Below 1 Ω




OK

4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)

NG

8.CHECK INSTRUMENT PANEL WIRE (OPEN)
4.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (SHORT)
U189105E02
1.375,3.594 1.573,3.177 false 1.938,3.594 1.75,3.177 false 2.25,1.49 3.135,1.813 0.885,0.323 10 false Center Airbag Sensor 0.219,0.99 1.01,1.313 0.792,0.323 10 false Front Airbag Sensor RH 2.375,0.417 2.5,0.583 0.125,0.167 10 false A 1.99,0.198 2.115,0.365 0.125,0.167 10 false B 1.615,0.198 1.74,0.365 0.125,0.167 10 false C 1.49,0.198 1.615,0.365 0.125,0.167 10 false D 1.135,0.198 1.26,0.365 0.125,0.167 10 false E 0.719,0.417 0.844,0.583 0.125,0.167 10 false F 1.188,2.271 1.979,2.417 0.792,0.146 10 false Connector E 0.833,3.021 1.146,3.208 0.313,0.188 10 false A18 1.083,3.594 1.365,3.771 0.281,0.177 10 false -SR 1.938,3.594 2.24,3.771 0.302,0.177 10 false +SR

a.

Disconnect the service wire from connector B.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A18-1 (-SR) - A18-2 (+SR) 1 MΩ or higher




OK

5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
5.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO B+)
U189105E02
1.375,3.594 1.573,3.177 false 1.938,3.594 1.75,3.177 false 2.25,1.49 3.135,1.813 0.885,0.323 10 false Center Airbag Sensor 0.219,0.99 1.01,1.313 0.792,0.323 10 false Front Airbag Sensor RH 2.375,0.417 2.5,0.583 0.125,0.167 10 false A 1.99,0.198 2.115,0.365 0.125,0.167 10 false B 1.615,0.198 1.74,0.365 0.125,0.167 10 false C 1.49,0.198 1.615,0.365 0.125,0.167 10 false D 1.135,0.198 1.26,0.365 0.125,0.167 10 false E 0.719,0.417 0.844,0.583 0.125,0.167 10 false F 1.188,2.271 1.979,2.417 0.792,0.146 10 false Connector E 0.833,3.021 1.146,3.208 0.313,0.188 10 false A18 1.083,3.594 1.365,3.771 0.281,0.177 10 false -SR 1.938,3.594 2.24,3.771 0.302,0.177 10 false +SR

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
A18-2 (+SR) - Body ground Below 1 V
A18-1 (-SR) - Body ground




OK

6.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND)

NG

10.CHECK INSTRUMENT PANEL WIRE (TO B+)
6.CHECK FRONT AIRBAG SENSOR RH CIRCUIT (TO GROUND)
U189105E02
1.375,3.594 1.573,3.177 false 1.938,3.594 1.75,3.177 false 2.25,1.49 3.135,1.813 0.885,0.323 10 false Center Airbag Sensor 0.219,0.99 1.01,1.313 0.792,0.323 10 false Front Airbag Sensor RH 2.375,0.417 2.5,0.583 0.125,0.167 10 false A 1.99,0.198 2.115,0.365 0.125,0.167 10 false B 1.615,0.198 1.74,0.365 0.125,0.167 10 false C 1.49,0.198 1.615,0.365 0.125,0.167 10 false D 1.135,0.198 1.26,0.365 0.125,0.167 10 false E 0.719,0.417 0.844,0.583 0.125,0.167 10 false F 1.188,2.271 1.979,2.417 0.792,0.146 10 false Connector E 0.833,3.021 1.146,3.208 0.313,0.188 10 false A18 1.083,3.594 1.365,3.771 0.281,0.177 10 false -SR 1.938,3.594 2.24,3.771 0.302,0.177 10 false +SR

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
A18-2 (+SR) - Body ground 1 MΩ or higher
A18-1 (-SR) - Body ground




OK

7.CHECK FRONT AIRBAG SENSOR RH

NG

11.CHECK INSTRUMENT PANEL WIRE (TO GROUND)
7.CHECK FRONT AIRBAG SENSOR RH
C128728E05
0.406,3.76 0.531,3.344 true 0.74,3.76 0.625,3.542 true 2.104,1.719 2.979,2.052 0.875,0.333 10 false Center Airbag Sensor 0.167,1.135 1.167,1.542 1,0.406 10 false Front Airbag Sensor LH 0.333,2.823 0.75,3 0.417,0.177 10 false DLC3 2.156,2.479 2.688,2.667 0.531,0.188 10 false DTC 83 2.167,3.594 2.698,3.781 0.531,0.188 10 false DTC 84 0.198,3.76 0.458,3.927 0.26,0.167 10 false CG 0.708,3.76 0.969,3.927 0.26,0.167 10 false TC

a.

Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor RH and LH, and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


g.

Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1602/83, B1603/83, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 are not output A
DTC B1602/83, B1603/83, B1612/83 and B1613/83 are output B
B1607/84, B1608/84, B1617/ 84 and B1618/84 are output C

HINT:

DTCs other than DTC B1602/83, B1603, B1612/83, B1613/83, B1607/84, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.




A

USE SIMULATION METHOD TO CHECK

B

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C

REPLACE FRONT AIRBAG SENSOR RH

8.CHECK INSTRUMENT PANEL WIRE (OPEN)
U189107E02
2.427,4.021 2.354,4.167 false 2.042,3.677 2.302,3.438 false 1.271,0.635 1.427,0.104 1.427,0.104 1.479,0.104 false 1.896,0.771 1.667,1.927 false 2.854,3.781 2.5,3.438 false 2.26,1.531 3.135,1.917 0.875,0.385 10 false Center Airbag Sensor 0.167,1.146 0.938,1.521 0.771,0.375 10 false Front Airbag Sensor RH 2.417,0.615 2.563,0.781 0.146,0.167 10 false A 2.052,0.865 2.198,1.031 0.146,0.167 10 false B 1.656,0.865 1.802,1.031 0.146,0.167 10 false C 1.448,0.865 1.594,1.031 0.146,0.167 10 false D 1.073,0.865 1.219,1.031 0.146,0.167 10 false E 0.708,0.625 0.854,0.792 0.146,0.167 10 false F 2.167,2.396 2.99,2.542 0.823,0.146 10 false Connector B 0.344,2.385 1.167,2.531 0.823,0.146 10 false Connector C 1.646,3.177 1.948,3.333 0.302,0.156 10 false G19 0.115,2.823 0.417,2.979 0.302,0.156 10 false AG7 1.667,4.188 2.573,4.365 0.906,0.177 10 false Service Wire 1.74,3.646 2.063,3.792 0.323,0.146 10 false +SR 2.844,3.802 3.167,3.948 0.323,0.146 10 false -SR 0.875,3.156 1,3.333 0.125,0.177 10 false 1 0.677,3.156 0.802,3.333 0.125,0.177 10 false 2 1.521,0.021 3.073,0.219 1.552,0.198 10 false Engine Room Main Wire 0.302,1.896 1.698,2.063 1.396,0.167 10 false Instrument Panel Wire

a.

Disconnect the engine room main wire connector from the instrument panel wire.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
AG7-1 - AG7-2 Below 1 Ω




OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

9.CHECK INSTRUMENT PANEL WIRE (SHORT)
U189108E02
1.281,0.635 1.375,0.135 1.375,0.135 1.427,0.135 false 1.885,0.771 1.656,1.875 false 2.344,1.521 3.25,1.844 0.906,0.323 10 false Center Airbag Sensor 2.417,0.594 2.563,0.76 0.146,0.167 10 false A 2.031,0.885 2.177,1.052 0.146,0.167 10 false B 1.667,0.875 1.813,1.042 0.146,0.167 10 false C 1.448,0.875 1.594,1.042 0.146,0.167 10 false D 1.063,0.875 1.208,1.042 0.146,0.167 10 false E 0.688,0.615 0.833,0.781 0.146,0.167 10 false F 0.135,1.135 0.938,1.479 0.802,0.344 10 false Front Airbag Sensor RH 1.177,2.51 2.01,2.656 0.833,0.146 10 false Connector C 0.719,3.25 1.052,3.427 0.333,0.177 10 false AG7 1.479,0.063 3.021,0.24 1.542,0.177 10 false Engine Room Main Wire 0.469,1.906 1.896,2.094 1.427,0.188 10 false Instrument Panel Wire 1.677,3.198 1.792,3.354 0.115,0.156 10 false 1 1.49,3.198 1.604,3.354 0.115,0.156 10 false 2

a.

Disconnect the engine room main wire connector from the instrument panel wire.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
AG7-1 - AG7-2 1 MΩ or higher




OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (TO B+)
U189108E02
1.281,0.635 1.375,0.135 1.375,0.135 1.427,0.135 false 1.885,0.771 1.656,1.875 false 2.344,1.521 3.25,1.844 0.906,0.323 10 false Center Airbag Sensor 2.417,0.594 2.563,0.76 0.146,0.167 10 false A 2.031,0.885 2.177,1.052 0.146,0.167 10 false B 1.667,0.875 1.813,1.042 0.146,0.167 10 false C 1.448,0.875 1.594,1.042 0.146,0.167 10 false D 1.063,0.875 1.208,1.042 0.146,0.167 10 false E 0.688,0.615 0.833,0.781 0.146,0.167 10 false F 0.135,1.135 0.938,1.479 0.802,0.344 10 false Front Airbag Sensor RH 1.177,2.51 2.01,2.656 0.833,0.146 10 false Connector C 0.719,3.25 1.052,3.427 0.333,0.177 10 false AG7 1.479,0.063 3.021,0.24 1.542,0.177 10 false Engine Room Main Wire 0.469,1.906 1.896,2.094 1.427,0.188 10 false Instrument Panel Wire 1.677,3.198 1.792,3.354 0.115,0.156 10 false 1 1.49,3.198 1.604,3.354 0.115,0.156 10 false 2

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the engine room main wire connector from the instrument panel wire.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG).


f.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
AG7-1 - Body ground Below 1 V
AG7-2 - Body ground




OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (TO GROUND)
U189108E02
1.281,0.635 1.375,0.135 1.375,0.135 1.427,0.135 false 1.885,0.771 1.656,1.875 false 2.344,1.521 3.25,1.844 0.906,0.323 10 false Center Airbag Sensor 2.417,0.594 2.563,0.76 0.146,0.167 10 false A 2.031,0.885 2.177,1.052 0.146,0.167 10 false B 1.667,0.875 1.813,1.042 0.146,0.167 10 false C 1.448,0.875 1.594,1.042 0.146,0.167 10 false D 1.063,0.875 1.208,1.042 0.146,0.167 10 false E 0.688,0.615 0.833,0.781 0.146,0.167 10 false F 0.135,1.135 0.938,1.479 0.802,0.344 10 false Front Airbag Sensor RH 1.177,2.51 2.01,2.656 0.833,0.146 10 false Connector C 0.719,3.25 1.052,3.427 0.333,0.177 10 false AG7 1.479,0.063 3.021,0.24 1.542,0.177 10 false Engine Room Main Wire 0.469,1.906 1.896,2.094 1.427,0.188 10 false Instrument Panel Wire 1.677,3.198 1.792,3.354 0.115,0.156 10 false 1 1.49,3.198 1.604,3.354 0.115,0.156 10 false 2

a.

Disconnect the engine room main wire connector from the instrument panel wire.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
AG7-1 - Body ground 1 MΩ or higher
AG7-2 - Body ground




OK

REPAIR OR REPLACE ENGINE ROOM MAIN WIRE

NG

REPAIR OR REPLACE INSTRUMENT PANEL WIRE