The front airbag sensor RH consists of the diagnostic circuit and the frontal deceleration sensor.
If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether or not the SRS should be activated.
DTC B1603/83 or B1613/83 is recorded when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1603/83
B1613/83 |
When one of following conditions is met:
·
Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in front airbag sensor RH circuit for 2 seconds ·
Front airbag sensor RH malfunction ·
Center airbag sensor malfunction |
·
Instrument panel wire ·
Engine room main wire ·
Front airbag sensor RH ·
Center airbag sensor |
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1602/83 is not output.
DTC B1612/83 is not output.
DTCs other than DTC B1602/83 and B1612/83 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the front airbag sensor RH.
Connectors are properly connected.
OK
NG
Disconnect the connectors from the center airbag sensor
Using a service wire, connect terminals G19-29 (+SR) and G19-27 (-SR) of connector B.
Do not forcibly insert a service wire into the terminals of the connector when connecting them.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| A18-1 (-SR) - A18-2 (+SR) | Below 1 Ω |
OK
NG
Disconnect the service wire from connector B.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| A18-1 (-SR) - A18-2 (+SR) | 1 MΩ or higher |
OK
NG
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| A18-2 (+SR) - Body ground | Below 1 V |
| A18-1 (-SR) - Body ground |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| A18-2 (+SR) - Body ground | 1 MΩ or higher |
| A18-1 (-SR) - Body ground |
OK
NG
Connect the connectors to the center airbag sensor.
Interchange the front airbag sensor RH and LH, and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1603/83, B1613/83, B1608/84 and B1618/84 are not output | A |
| DTC B1603/83 and B1613/83 are output | B |
| DTC B1608/84 and B1618/84 are not output | C |
DTCs other than DTC B1603, B1613/83, B1608/84 and B1618/ 84 may be output at this time, but they are not related to this check.
A
B
C
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| AG7-1 - AG7-2 | Below 1 Ω |
OK
NG
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| AG7-1 - AG7-2 | 1 MΩ or higher |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the engine room main wire connector from the instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch on (IG).
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| AG7-1 - Body ground | Below 1 V |
| AG7-2 - Body ground |
OK
NG
Disconnect the engine room main wire connector from the instrument panel wire.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| AG7-1 - Body ground | 1 MΩ or higher |
| AG7-2 - Body ground |
OK
NG