Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1840/59  Short in Driver Side Curtain Shield Squib 2nd Step Circuit  B1841/59  Open in Driver Side Curtain Shield Squib 2nd Step Circuit  B1842/59  Short to GND in Driver Side Curtain Shield Squib 2nd Step Circuit  B1843/59  Short to B+ in Driver Side Curtain Shield Squib 2nd Step Circuit  


DESCRIPTION

The driver side curtain shield squib 2nd step circuit consists of the center airbag sensor and the driver side curtain shield airbag.

The circuit instructs the SRS to deploy when the deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the driver side curtain shield squib 2nd step circuit.

DTC No. DTC Detection Condition Trouble Area
B1840/59 Center airbag sensor receives a line short signal 5 times in the driver side curtain shield squib 2nd step circuit during primary check.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor


B1841/59 Center airbag sensor receives an open signal in the driver side curtain shield squib 2nd step circuit for 2 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor


B1842/59 Center airbag sensor receives a short to ground signal in the driver side curtain shield squib 2nd step circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor


B1843/59 Center airbag sensor receives a short to B+ signal in the driver side curtain shield squib 2nd step circuit for 0.5 seconds.
·

Floor wire (for LHD)

·

Floor No. 2 wire (for RHD)

·

Curtain shield airbag LH (Driver side curtain shield squib) (for LHD)

·

Curtain shield airbag RH (Driver side curtain shield squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C368098E03
0.25,0.271 0.865,0.625 0.615,0.354 10 false for LHD: 1.01,2.448 1.625,2.802 0.615,0.354 10 false M13 1.01,2.615 3.271,2.979 2.26,0.365 10 false Curtain Shield Squib 2nd Step LH 2.281,1.156 2.896,1.51 0.615,0.354 10 false MPX5 2.74,1.156 3.125,1.396 0.385,0.24 10 false 2 2.729,2.01 3.115,2.25 0.385,0.24 10 false 1 4.656,1.125 5.042,1.365 0.385,0.24 10 false 4 4.656,1.99 5.042,2.229 0.385,0.24 10 false 5 4.781,3.167 5.167,3.406 0.385,0.24 10 false M9 4.781,3.344 6.708,3.656 1.927,0.313 10 false Center Airbag Sensor 4.875,1.25 5.26,1.49 0.385,0.24 10 false CD2+ 2.26,2.219 2.875,2.573 0.615,0.354 10 false MPX6 2.177,5.063 2.792,5.417 0.615,0.354 10 false GOSW 4.875,2.115 5.26,2.354 0.385,0.24 10 false CD2- 4.823,7.073 5.208,7.313 0.385,0.24 10 false N10 4.823,7.24 6.75,7.552 1.927,0.313 10 false Center Airbag Sensor 1.021,6.385 1.406,6.625 0.385,0.24 10 false N20 1.021,6.552 3.177,6.938 2.156,0.385 10 false Curtain Shield Squib 2nd Step RH 2.25,6.135 2.865,6.49 0.615,0.354 10 false GACT 2.74,5.042 3.125,5.281 0.385,0.24 10 false 2 2.74,5.948 3.125,6.188 0.385,0.24 10 false 1 4.625,5.052 5.01,5.292 0.385,0.24 10 false 4 4.625,5.938 5.01,6.177 0.385,0.24 10 false 5 4.865,5.167 5.25,5.406 0.385,0.24 10 false CD2+ 4.885,6.042 5.271,6.281 0.385,0.24 10 false CD2- 0.24,4 0.854,4.354 0.615,0.354 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK DRIVER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY (DRIVER SIDE CURTAIN SHIELD SQUIB)
C364220E02
4.167,0.417 4.583,0.667 0.417,0.25 4.167,0.75 4.583,1 0.417,0.25 0.552,1.26 0.552,1.083 0.552,1.083 1.104,0.958 false 4.167,2.469 4.313,2.167 true 4.51,2.458 4.385,2.292 true 1.177,0.594 1.49,0.792 0.313,0.198 10 false D 1.375,0.594 1.688,0.792 0.313,0.198 10 false C 0.281,1.281 1.26,1.854 0.979,0.573 10 false Driver Side Curtain Shield Squib 2nd Step 1.677,1.354 2.542,1.792 0.865,0.438 10 false Center Airbag Sensor 4.25,0.792 4.563,0.99 0.313,0.198 10 false N20 4.875,0.031 6.156,0.281 1.281,0.25 10 false Connector C 5.583,1.771 6.229,1.99 0.646,0.219 10 false DTC 59 4.188,1.781 4.604,1.979 0.417,0.198 10 false DLC3 4.042,2.479 4.354,2.677 0.313,0.198 10 false CG 4.448,2.49 4.76,2.688 0.313,0.198 10 false TC 4.625,0.458 4.938,0.656 0.313,0.198 10 false *1 4.646,0.781 4.958,0.979 0.313,0.198 10 false *2 4.25,0.458 4.563,0.656 0.313,0.198 10 false M13 5.958,0.771 7.156,1.052 1.198,0.281 10 false *1: for LHD 5.958,1.125 7.156,1.406 1.198,0.281 10 false *2: for RHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the driver side curtain shield airbag.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the driver side curtain shield airbag (driver side curtain shield squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1840, B1841, B1842, B1843 or 59 is not output.


HINT:

DTCs other than DTC B1840, B1841, B1842, B1843 or 59 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE DRIVER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the driver side curtain shield airbag) is not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB 2ND STEP CIRCUIT)

NG

REPAIR OR REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (DRIVER SIDE CURTAIN SHIELD SQUIB 2ND STEP CIRCUIT)
U188969E02
0.802,0.781 0.802,1.052 false 1.396,0.802 1.396,1.917 false 1.219,3.604 1.667,3.521 true 2.125,4.104 1.792,3.521 true 2.229,1.229 3.115,1.552 0.885,0.323 10 false Center Airbag Sensor 1.896,0.604 2.021,0.781 0.125,0.177 10 false A 1.521,0.333 1.646,0.51 0.125,0.177 10 false B 1.125,0.333 1.25,0.51 0.125,0.177 10 false C 0.906,0.333 1.031,0.51 0.125,0.177 10 false D 0.063,1.031 0.896,1.844 0.833,0.813 10 false Driver Side Curtain Shield Squib 2nd Step 1.25,2.802 2.083,2.979 0.833,0.177 10 false Connector C 1.177,1.927 1.979,2.094 0.802,0.167 10 false Floor Wire*1 1.177,2.229 2.365,2.396 1.188,0.167 10 false Floor No. 2 Wire*2 2.323,3.302 2.646,3.448 0.323,0.146 10 false M13 2.323,3.688 2.615,3.844 0.292,0.156 10 false N20 2.719,3.448 2.896,3.625 0.177,0.177 10 false *1 2.677,3.854 2.854,4.031 0.177,0.177 10 false *2 2.021,4.146 2.573,4.333 0.552,0.188 10 false MPX6*1 2.021,4.333 2.646,4.521 0.625,0.188 10 false GOSW*2 0.563,3.552 1.125,3.74 0.563,0.188 10 false MPX5*1 0.563,3.74 1.125,3.927 0.563,0.188 10 false GACT*2 0.302,4.052 1.042,4.219 0.74,0.167 10 false *1: for LHD 0.302,4.302 1.042,4.469 0.74,0.167 10 false *2: for RHD

a.

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
M13-1 (MPX5) - Body ground Below 1 V
M13-2 (MPX6) - Body ground

for RHD:
Tester Connection Specified Condition
N20-1 (GACT) - Body ground Below 1 V
N20-2 (GOSW) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M13-1 (MFX5) - M13-2 (MFX5) Below 1 Ω
M13-1 (MFX5) - Body ground 1 MΩ or higher
M13-2 (MPX6) - Body ground

for RHD:
Tester Connection Specified Condition
N20-1 (GACT) - N20-2 (GOSW) Below 1 Ω
N20-1 (GACT) - Body ground 1 MΩ or higher
N20-2 (GOSW) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
M13-1 (MPX5) - M13-2 (MPX6) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
N20-1 (GACT) - N20-2 (GOSW) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE