Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1845/61  Short in Passenger Side Curtain Shield Squib 2nd Step Circuit  B1846/61  Open in Passenger Side Curtain Shield Squib 2nd Step Circuit  B1847/61  Short to GND in Passenger Side Curtain Shield Squib 2nd Step Circuit  B1848/61  Short to B+ in Passenger Side Curtain Shield Squib 2nd Step Circuit  


DESCRIPTION

The front passenger side curtain shield squib 2nd step circuit consists of the center airbag sensor and the front passenger side curtain shield airbag.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the front passenger side curtain shield squib 2nd step circuit.

DTC No. DTC Detection Condition Trouble Area
B1845/61 Center airbag sensor receives a line short circuit signal 5 times in the front passenger side curtain shield squib 2nd step circuit during primary check.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor


B1846/61 Center airbag sensor receives an open signal in the front passenger side curtain shield squib 2nd step circuit for 2 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor


B1847/61 Center airbag sensor receives a short to ground signal in the front passenger side curtain shield squib 2nd step circuit for 0.5 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor


B1848/61 center airbag sensor receives a short to B+ signal in the front passenger side curtain shield squib 2nd step circuit for 0.5 seconds.
·

Floor No. 2 wire (for LHD)

·

Floor wire (for RHD)

·

Curtain shield airbag RH (Front passenger side curtain shield squib) (for LHD)

·

Curtain shield airbag LH (Front passenger side curtain shield squib) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C368098E04
0.25,0.271 0.865,0.625 0.615,0.354 10 false for LHD: 1.01,2.448 1.625,2.802 0.615,0.354 10 false N20 1.01,2.615 3.271,2.979 2.26,0.365 10 false Curtain Shield Squib 2nd Step RH 2.198,1.156 2.813,1.51 0.615,0.354 10 false GOSW 2.74,1.156 3.125,1.396 0.385,0.24 10 false 2 2.729,2.01 3.115,2.25 0.385,0.24 10 false 1 4.656,1.125 5.042,1.365 0.385,0.24 10 false 2 4.656,1.99 5.042,2.229 0.385,0.24 10 false 1 4.781,3.167 5.167,3.406 0.385,0.24 10 false N9 4.781,3.344 6.708,3.656 1.927,0.313 10 false Center Airbag Sensor 4.875,1.25 5.26,1.49 0.385,0.24 10 false CP2+ 2.26,2.219 2.875,2.573 0.615,0.354 10 false GACT 2.26,5.063 2.875,5.417 0.615,0.354 10 false MPX5 4.875,2.115 5.26,2.354 0.385,0.24 10 false CP2- 4.823,7.073 5.208,7.313 0.385,0.24 10 false M10 4.823,7.24 6.75,7.552 1.927,0.313 10 false Center Airbag Sensor 1.021,6.385 1.406,6.625 0.385,0.24 10 false M13 1.021,6.552 3.177,6.938 2.156,0.385 10 false Curtain Shield Squib 2nd Step LH 2.25,6.135 2.865,6.49 0.615,0.354 10 false MPX6 2.74,5.042 3.125,5.281 0.385,0.24 10 false 2 2.74,5.948 3.125,6.188 0.385,0.24 10 false 1 4.625,5.052 5.01,5.292 0.385,0.24 10 false 2 4.625,5.938 5.01,6.177 0.385,0.24 10 false 1 4.865,5.167 5.25,5.406 0.385,0.24 10 false CP2+ 4.885,6.042 5.271,6.281 0.385,0.24 10 false CP2- 0.24,4 0.854,4.354 0.615,0.354 10 false for RHD:

CAUTION / NOTICE / HINT

HINT:
·

Perform the simulation method by selecting the "Check Mode" (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting the "Check Mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).



PROCEDURE

1.CHECK FRONT PASSENGER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY (FRONT PASSENGER SIDE CURTAIN SHIELD SQUIB)
C364221E02
4.083,0.583 4.5,0.833 0.417,0.25 4.083,0.917 4.5,1.167 0.417,0.25 1.177,1.385 1.177,1.219 false 4.198,2.531 4.375,2.229 true 4.635,2.552 4.479,2.365 true 1.281,0.875 1.594,1.073 0.313,0.198 10 false D 1.438,0.875 1.75,1.073 0.313,0.198 10 false C 0.25,1.396 1.604,1.927 1.354,0.531 10 false Front Passenger Side Curtain Shield Squib 2nd Step 1.781,1.396 2.635,1.885 0.854,0.49 10 false Center Airbag Sensor 4.844,0.052 5.948,0.323 1.104,0.271 10 false Connector C 4.156,0.625 4.469,0.823 0.313,0.198 10 false N20 4.281,1.833 4.698,2.031 0.417,0.198 10 false DLC3 5.656,1.813 6.24,2.073 0.583,0.26 10 false DTC 61 4.042,2.542 4.354,2.74 0.313,0.198 10 false CG 4.594,2.573 4.906,2.771 0.313,0.198 10 false TC 4.542,0.615 4.854,0.813 0.313,0.198 10 false *1 5.917,0.823 7.156,1.063 1.24,0.24 10 false *1: for LHD 4.156,0.958 4.469,1.156 0.313,0.198 10 false M13 4.552,0.958 4.865,1.156 0.313,0.198 10 false *2 5.917,1.156 7.156,1.396 1.24,0.24 10 false *2: for RHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front passenger side curtain shield airbag.


d.

Connect SST (resistance 2.1 Ω) to connector C.


CAUTION:

Never connect a tester to the curtain shield airbag (front passenger side curtain shield squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting them.

·

Insert straight SST into the terminals of the connector.



SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


j.

Check the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1845, B1846, B1847, B1848 or 61 is not output.


HINT:

DTCs other than DTC B1845, B1846, B1847, B1848 or 61 may be output at this time, but they are not related to this check.




NG

2.CHECK CONNECTOR

OK

REPLACE FRONT PASSENGER SIDE CURTAIN SHIELD AIRBAG ASSEMBLY

2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Check that the floor wire connector (on the passenger side curtain shield airbag) are not damaged.

OK:

Lock button is not disengaged, and claw of lock is not deformed or damaged.




OK

3.CHECK FLOOR WIRE

NG

REPAIR OR REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE
U188971E02
1.688,2.083 1.563,2.083 1.563,2.083 1.563,0.979 false 0.958,0.979 0.958,1.177 false 1.146,3.625 1.625,3.563 true 2.25,4.177 1.792,3.563 true 2.042,0.823 2.177,0.99 0.135,0.167 10 false A 1.667,0.594 1.802,0.76 0.135,0.167 10 false B 1.271,0.594 1.406,0.76 0.135,0.167 10 false C 1.052,0.594 1.188,0.76 0.135,0.167 10 false D 1.875,1.135 2.76,1.49 0.885,0.354 10 false Center Airbag Sensor 1.75,2.021 2.917,2.177 1.167,0.156 10 false Floor No. 2 Wire*1 1.75,2.333 2.563,2.49 0.813,0.156 10 false Floor Wire*2 0.115,1.167 1.26,1.844 1.146,0.677 10 false Front Passenger Side Curtain Shield Squib 2nd Step 1.24,2.896 2.083,3.052 0.844,0.156 10 false Connector C 2.344,3.323 2.635,3.49 0.292,0.167 10 false N20 2.344,3.74 2.667,3.906 0.323,0.167 10 false M13 2.698,3.521 2.865,3.698 0.167,0.177 10 false *1 2.708,3.906 2.875,4.083 0.167,0.177 10 false *2 0.521,3.583 1.073,3.729 0.552,0.146 10 false GACT*1 0.542,3.792 1.073,3.938 0.531,0.146 10 false MPX5*2 2.052,4.208 2.646,4.354 0.594,0.146 10 false GOSW*1 2.052,4.427 2.615,4.573 0.563,0.146 10 false MPX6*2 0.354,4.083 1.063,4.229 0.708,0.146 10 false *1: for LHD 0.354,4.354 1.104,4.5 0.75,0.146 10 false *2: for RHD

a.

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch on (IG).


d.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
N20-1 (GACT) - Body ground Below 1 V
N20-2 (GOSW) - Body ground

for RHD:
Tester Connection Specified Condition
M13-1 (MPX5) - Body ground Below 1 V
M13-2 (MPX6) - Body ground



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N20-1 (GACT) - N20-2 (GOSW) Below 1 Ω
N20-1 (GACT) - Body ground 1 MΩ or higher
N20-2 (GOSW) - Body ground

for RHD:
Tester Connection Specified Condition
M13-1 (MPX5) - M13-2 (MPX6) Below 1 Ω
M13-1 (MPX5) - Body ground 1 MΩ or higher
M13-2 (MPX6) - Body ground



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N20-1 (GACT) - N20-2 (GOSW) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
M13-1 (MPX5) - M13-2 (MPX6) 1 MΩ or higher




OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPAIR OR REPLACE FLOOR WIRE