Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1697/82  Lost Communication with Rear Passenger Side - Side Airbag Sensor  


DESCRIPTION

The front passenger side - side airbag sensor (for rear side) consists of parts including the diagnostic circuit and the lateral deceleration sensor.

When the center airbag sensor receives signals from the lateral deceleration sensor, it determines whether or not the SRS should be activated.

DTC B1697/82 is set when a malfunction is detected in the front passenger side - side airbag sensor (for rear side) circuit.

DTC No. DTC Detection Condition Trouble Area
B1697/82 When one of following conditions is met:
·

Center airbag sensor detects line short signal, open signal, short to ground signal or short to B+ signal in front passenger side - side airbag sensor (for rear side) circuit for 2 seconds.

·

Driver side - side airbag sensor (for rear side) malfunction

·

Center airbag sensor malfunction


·

Floor No. 2 wire (for LHD)

·

Floor wire (for LHD)

·

Door wire RH (for LHD)

·

Door wire LH (for RHD)

·

Side airbag sensor RH (for rear side) (for LHD)

·

Slide door airbag sensor LH (for rear side) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C141670E03
0.219,0.469 0.979,0.719 0.76,0.25 10 false for LHD: 0.198,4.688 0.896,4.906 0.698,0.219 10 false for RHD: 0.083,8.167 1.563,8.385 1.479,0.219 10 false Rear Airbag Sensor LH 2.344,8.052 3.854,8.427 1.51,0.375 10 false Side Airbag Sensor LH (for Rear Side) 4.74,8.042 5.677,8.427 0.938,0.385 10 false Rear Floor Airbag Sensor 6,8.177 6.917,8.552 0.917,0.375 10 false Center Airbag Sensor 0.771,5.385 1.198,5.573 0.427,0.188 10 false BCL+ 3.01,5.385 3.448,5.583 0.438,0.198 10 false BCL+ 0.792,5.885 1.188,6.104 0.396,0.219 10 false BCL- 3.021,5.875 3.438,6.104 0.417,0.229 10 false BCL- 0.75,7.063 1.208,7.292 0.458,0.229 10 false BDL+ 2.521,7.063 2.958,7.271 0.438,0.208 10 false BDL+ 1.708,7.063 2.021,7.271 0.313,0.208 10 false LM3 0.792,7.563 1.229,7.781 0.438,0.219 10 false BDL- 2.51,7.542 3,7.76 0.49,0.219 10 false BDL- 3.583,5.375 4.01,5.573 0.427,0.198 10 false BBL+ 3.625,5.875 3.99,6.073 0.365,0.198 10 false BBL- 3.083,7.063 3.51,7.281 0.427,0.219 10 false BEL+ 4.854,7.052 5.323,7.24 0.469,0.188 10 false BEL+ 3.115,7.552 3.521,7.729 0.406,0.177 10 false BEL- 4.854,7.542 5.219,7.719 0.365,0.177 10 false BEL- 6.073,5.385 6.542,5.594 0.469,0.208 10 false BBP+ 5.823,5.25 6.01,5.458 0.188,0.208 10 false 8 5.771,5.75 5.99,5.958 0.219,0.208 10 false 11 4.073,5.281 4.26,5.49 0.188,0.208 10 false 4 4.073,5.76 4.292,5.969 0.219,0.208 10 false 3 1.26,5.26 1.448,5.469 0.188,0.208 10 false 4 1.25,5.76 1.469,5.969 0.219,0.208 10 false 3 1.25,6.938 1.438,7.146 0.188,0.208 10 false 1 1.792,6.844 1.979,7.052 0.188,0.208 10 false 1 1.698,7.552 2.01,7.76 0.313,0.208 10 false LM3 1.792,7.354 1.979,7.563 0.188,0.208 10 false 2 3.958,7.063 4.271,7.271 0.313,0.208 10 false LM3 4.052,6.854 4.24,7.063 0.188,0.208 10 false 3 3.958,7.552 4.271,7.76 0.313,0.208 10 false LM3 4.052,7.344 4.24,7.552 0.188,0.208 10 false 4 1.25,7.448 1.469,7.656 0.219,0.208 10 false 2 3.573,6.948 3.76,7.156 0.188,0.208 10 false 1 3.563,7.438 3.781,7.646 0.219,0.208 10 false 2 4.635,6.948 4.823,7.156 0.188,0.208 10 false 2 4.635,7.438 4.854,7.646 0.219,0.208 10 false 1 2.313,6.948 2.5,7.156 0.188,0.208 10 false 4 2.313,7.438 2.531,7.646 0.219,0.208 10 false 3 2.792,5.271 2.979,5.479 0.188,0.208 10 false 1 2.781,5.76 3,5.969 0.219,0.208 10 false 2 6.073,5.875 6.49,6.052 0.417,0.177 10 false BBP- 2.563,6.354 4.948,6.573 2.385,0.219 10 false Side Airbag Sensor LH (for Front Side) 1.698,2.875 2.01,3.083 0.313,0.208 10 false KN3 1.792,2.667 1.979,2.875 0.188,0.208 10 false 1 1.698,3.375 2.01,3.583 0.313,0.208 10 false KN3 1.792,3.167 1.979,3.375 0.188,0.208 10 false 2 3.76,2.875 4.073,3.083 0.313,0.208 10 false KN3 3.865,2.667 4.052,2.875 0.188,0.208 10 false 3 3.771,3.365 4.083,3.573 0.313,0.208 10 false KN3 3.844,3.167 4.031,3.375 0.188,0.208 10 false 4 4.302,2.875 4.615,3.083 0.313,0.208 10 false NM1 4.385,2.677 4.573,2.885 0.188,0.208 10 false 2 4.292,3.365 4.604,3.573 0.313,0.208 10 false NM1 4.385,3.167 4.573,3.375 0.188,0.208 10 false 1 0.229,4.031 1.688,4.271 1.458,0.24 10 false Rear Airbag Sensor RH 2.271,3.865 3.802,4.219 1.531,0.354 10 false Side Airbag Sensor RH (for Rear Side) 4.76,3.896 5.708,4.271 0.948,0.375 10 false Center Floor Airbag Sensor 5.958,4.021 6.844,4.406 0.885,0.385 10 false Center Airbag Sensor 0.74,1.198 1.167,1.385 0.427,0.188 10 false BCR+ 3.021,1.198 3.458,1.396 0.438,0.198 10 false BCR+ 0.75,1.698 1.146,1.917 0.396,0.219 10 false BCR- 3.01,1.688 3.427,1.917 0.417,0.229 10 false BCR- 0.729,2.875 1.188,3.104 0.458,0.229 10 false BDR+ 2.51,2.875 2.948,3.083 0.438,0.208 10 false BDR+ 0.75,3.375 1.188,3.594 0.438,0.219 10 false BDR- 2.521,3.365 3.01,3.583 0.49,0.219 10 false BDR- 3.563,1.198 3.99,1.396 0.427,0.198 10 false BBR+ 3.594,1.688 3.958,1.885 0.365,0.198 10 false BBR- 3.063,2.875 3.49,3.094 0.427,0.219 10 false BER+ 4.854,2.875 5.323,3.063 0.469,0.188 10 false BER+ 3.104,3.365 3.51,3.542 0.406,0.177 10 false BER- 4.865,3.354 5.229,3.531 0.365,0.177 10 false BER- 6.063,1.198 6.51,1.375 0.448,0.177 10 false BBP+ 5.833,1.083 6.021,1.292 0.188,0.208 10 false 8 5.781,1.573 6,1.781 0.219,0.208 10 false 11 4.063,1.073 4.25,1.281 0.188,0.208 10 false 4 4.063,1.563 4.281,1.771 0.219,0.208 10 false 3 1.271,1.073 1.458,1.281 0.188,0.208 10 false 4 1.25,1.563 1.469,1.771 0.219,0.208 10 false 3 1.26,2.74 1.448,2.948 0.188,0.208 10 false 1 1.25,3.25 1.469,3.458 0.219,0.208 10 false 2 3.563,2.75 3.75,2.958 0.188,0.208 10 false 1 3.563,3.25 3.781,3.458 0.219,0.208 10 false 2 4.656,2.771 4.844,2.979 0.188,0.208 10 false 2 4.656,3.26 4.875,3.469 0.219,0.208 10 false 1 2.292,2.75 2.479,2.958 0.188,0.208 10 false 4 2.302,3.26 2.521,3.469 0.219,0.208 10 false 3 2.781,1.073 2.969,1.281 0.188,0.208 10 false 1 2.781,1.563 3,1.771 0.219,0.208 10 false 2 6.063,1.708 6.479,1.885 0.417,0.177 10 false BBP- 2.333,2.198 4.76,2.406 2.427,0.208 10 false Side Airbag Sensor RH (for Front Side) 2.333,2.021 2.792,2.219 0.458,0.198 10 false N12 0.229,3.854 0.688,4.052 0.458,0.198 10 false N23 2.271,3.698 2.729,3.896 0.458,0.198 10 false K10 4.76,3.719 5.073,3.917 0.313,0.198 10 false M4 5.958,3.844 6.271,4.042 0.313,0.198 10 false N9 2.573,6.177 3.031,6.375 0.458,0.198 10 false M16 0.083,8 0.542,8.198 0.458,0.198 10 false M20 2.344,7.875 2.802,8.073 0.458,0.198 10 false L10 4.729,7.875 5.188,8.073 0.458,0.198 10 false M21 6,8.01 6.458,8.208 0.458,0.198 10 false M10

PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


b.

Turn the ignition switch off.


c.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


d.

Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1698 is output. A
DTC B1693 is output. B

HINT:

DTCs other than DTC B1698 and B1693 may be output at this time, but they are not related to this check.




A

2.CHECK CONNECTION OF CONNECTOR

B

Go to DTC B1692/81

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor, rear airbag sensor (for front passenger side), front passenger side - side airbag sensor (for front side) and the front passenger side - side airbag sensor (for rear side).

OK:

Connectors are properly connected.




OK

3.CHECK FLOOR WIRE (OPEN)

NG

CONNECT CONNECTOR

3.CHECK FLOOR WIRE (OPEN)
C366262E01
0.083,3.083 0.5,3.333 0.417,0.25 0.083,2.583 0.5,2.833 0.417,0.25 1.667,2.583 2.083,2.833 0.417,0.25 1.667,3.083 2.083,3.333 0.417,0.25 1.948,1.49 1.771,1.49 1.771,1.49 1.646,1.125 false 0.677,3.792 0.948,3.448 true 1.26,3.813 1.021,3.458 true 2.01,3.656 2.531,3.302 true 3,3.635 2.729,3.469 true 2.667,4.073 2.771,3.688 false 2.448,0.177 2.896,0.74 0.448,0.563 10 false Center Airbag Sensor 2.177,0.958 2.604,1.24 0.427,0.281 10 false A 2,1.406 3.229,1.667 1.229,0.26 10 false Floor No. 2 Wire*1 1.76,0.75 2.188,1.031 0.427,0.281 10 false B 1.417,0.75 1.844,1.031 0.427,0.281 10 false C 1,0.979 1.427,1.26 0.427,0.281 10 false D 0.219,1.594 1.677,2.344 1.458,0.75 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.594,2.573 1.573,2.823 0.979,0.25 10 false Connector C 0.177,2.615 0.604,2.896 0.427,0.281 10 false N12 0.156,3.125 0.583,3.406 0.427,0.281 10 false M16 0.365,2.854 0.792,3.135 0.427,0.281 10 false *1 0.365,3.354 0.792,3.635 0.427,0.281 10 false *2 1.792,2.625 2.219,2.906 0.427,0.281 10 false N9 1.75,3.125 2.177,3.406 0.427,0.281 10 false M10 1.802,3.667 2.229,3.948 0.427,0.281 10 false BBP+ 2.896,3.667 3.323,3.948 0.427,0.281 10 false BBP- 2.25,4.104 3.125,4.427 0.875,0.323 10 false Service Wire 0.292,4.354 1.094,4.667 0.802,0.313 10 false *1: for LHD 0.354,3.792 0.938,4.052 0.583,0.26 10 false BBR-*1 0.365,3.969 0.927,4.271 0.563,0.302 10 false BBL-*2 1.094,3.833 1.656,4.146 0.563,0.313 10 false BBR+*1 1.094,4.01 1.667,4.302 0.573,0.292 10 false BBL+*2 2.01,1.677 3.24,1.938 1.229,0.26 10 false Floor Wire*2 2.177,2.521 3.156,2.771 0.979,0.25 10 false Connector B 1.198,4.354 2,4.667 0.802,0.313 10 false *2: for RHD 1.927,3.365 2.354,3.646 0.427,0.281 10 false *2 1.938,2.854 2.365,3.135 0.427,0.281 10 false *1

a.

Disconnect the connectors from the center airbag sensor and the front passenger side - side airbag sensor (for front side).


b.

for LHD:

Using a service wire, connect terminals N9-8 (BBP+) and N9-11 (BBP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting them.



c.

for RHD:

Using a service wire, connect terminals M10-8 (BBP+) and M10-11 (BBP-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting them.



d.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N12-3 (BBR-) - N12-4 (BBR+) Below 1 Ω

for RHD:
Tester Connection Specified Condition
M16-3 (BBL-) - M16-4 (BBL+) Below 1 Ω




OK

4.CHECK FLOOR WIRE (SHORT)

NG

REPAIR OR REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT)
U189133E02
1.656,1.135 2.042,1.75 false 1.615,4.052 1.688,3.656 false 2.208,3.844 1.781,3.646 false 2.375,0.198 2.906,0.719 0.531,0.521 10 false Center Airbag Sensor 2.146,0.99 2.271,1.156 0.125,0.167 10 false A 1.76,0.729 1.885,0.896 0.125,0.167 10 false B 1.396,0.729 1.521,0.896 0.125,0.167 10 false C 1.021,1.01 1.146,1.177 0.125,0.167 10 false D 0.167,1.573 1.271,2.302 1.104,0.729 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 2,1.771 3.177,1.948 1.177,0.177 10 false Floor No. 2 Wire*1 2,2.104 2.792,2.281 0.792,0.177 10 false Floor Wire*2 2.073,3.01 2.885,3.167 0.813,0.156 10 false Connector C 1.354,4.063 1.854,4.24 0.5,0.177 10 false BBR-*1 1.354,4.229 1.854,4.406 0.5,0.177 10 false BBL-*2 2.24,3.792 2.792,3.969 0.552,0.177 10 false BBR+*1 2.24,3.99 2.792,4.167 0.552,0.177 10 false BBL+*2 0.656,3.271 0.948,3.427 0.292,0.156 10 false N12 0.667,3.573 0.958,3.729 0.292,0.156 10 false M16 1.052,3.208 1.208,3.365 0.156,0.156 10 false *1 1.052,3.51 1.208,3.667 0.156,0.156 10 false *2 0.031,3.927 0.792,4.135 0.76,0.208 10 false *1: for LHD 0.031,4.24 0.792,4.448 0.76,0.208 10 false *2: for RHD

a.

Disconnect the service wire from connector B.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N12-3 (BBR-) - N12-4 (BBR+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
M16-3 (BBL-) - M16-4 (BBL+) 1 MΩ or higher




OK

5.CHECK FLOOR WIRE (TO B+)

NG

REPAIR OR REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (TO B+)
U189133E02
1.656,1.135 2.042,1.75 false 1.615,4.052 1.688,3.656 false 2.208,3.844 1.781,3.646 false 2.375,0.198 2.906,0.719 0.531,0.521 10 false Center Airbag Sensor 2.146,0.99 2.271,1.156 0.125,0.167 10 false A 1.76,0.729 1.885,0.896 0.125,0.167 10 false B 1.396,0.729 1.521,0.896 0.125,0.167 10 false C 1.021,1.01 1.146,1.177 0.125,0.167 10 false D 0.167,1.573 1.271,2.302 1.104,0.729 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 2,1.771 3.177,1.948 1.177,0.177 10 false Floor No. 2 Wire*1 2,2.104 2.792,2.281 0.792,0.177 10 false Floor Wire*2 2.073,3.01 2.885,3.167 0.813,0.156 10 false Connector C 1.354,4.063 1.854,4.24 0.5,0.177 10 false BBR-*1 1.354,4.229 1.854,4.406 0.5,0.177 10 false BBL-*2 2.24,3.792 2.792,3.969 0.552,0.177 10 false BBR+*1 2.24,3.99 2.792,4.167 0.552,0.177 10 false BBL+*2 0.656,3.271 0.948,3.427 0.292,0.156 10 false N12 0.667,3.573 0.958,3.729 0.292,0.156 10 false M16 1.052,3.208 1.208,3.365 0.156,0.156 10 false *1 1.052,3.51 1.208,3.667 0.156,0.156 10 false *2 0.031,3.927 0.792,4.135 0.76,0.208 10 false *1: for LHD 0.031,4.24 0.792,4.448 0.76,0.208 10 false *2: for RHD

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
N12-3 (BBR-) - Body ground Below 1 V
N12-4 (BBR+) - Body ground

for RHD:
Tester Connection Specified Condition
M16-3 (BBL-) - Body ground Below 1 V
M16-4 (BBL+) - Body ground




OK

6.CHECK FLOOR WIRE (TO GROUND)

NG

REPAIR OR REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (TO GROUND)
U189133E02
1.656,1.135 2.042,1.75 false 1.615,4.052 1.688,3.656 false 2.208,3.844 1.781,3.646 false 2.375,0.198 2.906,0.719 0.531,0.521 10 false Center Airbag Sensor 2.146,0.99 2.271,1.156 0.125,0.167 10 false A 1.76,0.729 1.885,0.896 0.125,0.167 10 false B 1.396,0.729 1.521,0.896 0.125,0.167 10 false C 1.021,1.01 1.146,1.177 0.125,0.167 10 false D 0.167,1.573 1.271,2.302 1.104,0.729 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 2,1.771 3.177,1.948 1.177,0.177 10 false Floor No. 2 Wire*1 2,2.104 2.792,2.281 0.792,0.177 10 false Floor Wire*2 2.073,3.01 2.885,3.167 0.813,0.156 10 false Connector C 1.354,4.063 1.854,4.24 0.5,0.177 10 false BBR-*1 1.354,4.229 1.854,4.406 0.5,0.177 10 false BBL-*2 2.24,3.792 2.792,3.969 0.552,0.177 10 false BBR+*1 2.24,3.99 2.792,4.167 0.552,0.177 10 false BBL+*2 0.656,3.271 0.948,3.427 0.292,0.156 10 false N12 0.667,3.573 0.958,3.729 0.292,0.156 10 false M16 1.052,3.208 1.208,3.365 0.156,0.156 10 false *1 1.052,3.51 1.208,3.667 0.156,0.156 10 false *2 0.031,3.927 0.792,4.135 0.76,0.208 10 false *1: for LHD 0.031,4.24 0.792,4.448 0.76,0.208 10 false *2: for RHD

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N12-3 (BBR-) - Body ground 1 MΩ or higher
N12-4 (BBR+) - Body ground

for RHD:
Tester Connection Specified Condition
M16-3 (BBL-) - Body ground 1 MΩ or higher
M16-4 (BBL+) - Body ground




OK

7.CHECK FLOOR WIRE (OPEN)

NG

REPAIR OR REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (OPEN)
C364217E07
0.042,3.333 0.458,3.583 0.417,0.25 1.583,3.333 2,3.583 0.417,0.25 0.042,3 0.458,3.25 0.417,0.25 1.583,3 2,3.25 0.417,0.25 0.823,3.969 1.01,3.688 true 1.281,3.979 1.094,3.688 true 2.802,4.104 2.469,3.698 true 2.177,4.104 2.333,3.698 true 2.021,4.542 1.833,4.542 1.833,4.542 2.01,4.063 false 1.563,2.052 1.563,1.271 1.563,1.271 1.75,0.958 false 1.125,0.802 1.438,1 0.313,0.198 10 false D 1.521,0.583 1.833,0.781 0.313,0.198 10 false C 1.865,0.583 2.177,0.781 0.313,0.198 10 false B 2.292,0.813 2.604,1.01 0.313,0.198 10 false A 1.865,1.406 3.313,2.063 1.448,0.656 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.219,1.406 1.479,1.969 1.26,0.563 10 false Rear Airbag Sensor (for Front Passenger Side) 0.969,2.115 2.198,2.438 1.229,0.323 10 false Floor No. 2 Wire*1 0.552,2.76 1.594,3.063 1.042,0.302 10 false Connector C 0.115,3.375 0.427,3.573 0.313,0.198 10 false M20 2.083,4.448 2.938,4.646 0.854,0.198 10 false Service Wire 2.063,2.76 3.104,3.063 1.042,0.302 10 false Connector B 1.646,3.375 1.958,3.573 0.313,0.198 10 false M16 0.49,3.979 1.01,4.188 0.521,0.208 10 false BCR-*1 1.229,4 1.792,4.229 0.563,0.229 10 false BCR+*1 1.229,4.156 1.792,4.385 0.563,0.229 10 false BCL+*2 0.49,4.135 1.063,4.354 0.573,0.219 10 false BCL-*2 0.969,2.385 2.354,2.719 1.385,0.333 10 false Floor Wire*2 0.115,3.042 0.427,3.24 0.313,0.198 10 false N23 0.51,3.031 0.823,3.229 0.313,0.198 10 false *1 0.49,3.333 0.802,3.531 0.313,0.198 10 false *2 1.656,3.042 1.969,3.24 0.313,0.198 10 false N12 2.042,3.042 2.354,3.24 0.313,0.198 10 false *1 2.021,3.333 2.333,3.531 0.313,0.198 10 false *2 2.698,4.115 3.219,4.323 0.521,0.208 10 false BCR-*1 0.094,4.406 0.875,4.667 0.781,0.26 10 false *1: for LHD 2.698,4.26 3.271,4.479 0.573,0.219 10 false BCL-*2 2.01,4.125 2.573,4.354 0.563,0.229 10 false BCR+*1 2.01,4.271 2.573,4.5 0.563,0.229 10 false BCL+*2 0.875,4.406 1.656,4.667 0.781,0.26 10 false *2: for RHD

a.

Disconnect the connectors from the front passenger side - side airbag sensor (for front side) and the rear airbag sensor (for front passenger side).


b.

for LHD:

Using a service wire, connect terminals N12-1 (BCR+) and N12-2 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting them.



c.

for RHD:

Using a service wire, connect terminals M16-1 (BCL+) and M16-2 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting them.



d.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N23-3 (BCR-) - N23-4 (BCR+) Below 1 Ω

for RHD:
Tester Connection Specified Condition
M20-3 (BCL-) - M20-4 (BCL+) Below 1 Ω




OK

8.CHECK FLOOR WIRE (SHORT)

NG

REPAIR OR REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (SHORT)
U189145E02
1.531,2.417 1.646,2.417 1.646,2.417 1.646,0.875 false 1.615,4.104 1.771,3.771 false 2.219,4.031 1.875,3.771 false 1.708,1.333 3.156,2.021 1.448,0.688 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.104,1.333 1.448,1.865 1.344,0.531 10 false Rear Airbag Sensor (for Front Passenger Side) 2.24,0.74 2.365,0.896 0.125,0.156 10 false A 1.854,0.5 1.979,0.656 0.125,0.156 10 false B 1.49,0.479 1.615,0.635 0.125,0.156 10 false C 1.094,0.729 1.219,0.885 0.125,0.156 10 false D 1.26,2.792 2.115,2.958 0.854,0.167 10 false Connector C 0.219,2.604 1.031,2.771 0.813,0.167 10 false Floor Wire*2 0.219,2.323 1.417,2.49 1.198,0.167 10 false Floor No. 2 Wire*1 0.063,3.896 0.792,4.063 0.729,0.167 10 false *1: for LHD 0.063,4.188 0.792,4.354 0.729,0.167 10 false *2: for RHD 0.688,3.635 0.99,3.781 0.302,0.146 10 false M20 0.688,3.344 0.99,3.49 0.302,0.146 10 false N23 1.094,3.333 1.26,3.5 0.167,0.167 10 false *1 1.094,3.615 1.271,3.781 0.177,0.167 10 false *2 1.344,4.281 1.844,4.438 0.5,0.156 10 false BCL-*2 2.25,4.135 2.802,4.292 0.552,0.156 10 false BCL+*2 1.344,4.115 1.844,4.271 0.5,0.156 10 false BCR-*1 2.25,3.979 2.802,4.135 0.552,0.156 10 false BCR+*1

a.

Disconnect the service wire from connector B.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N23-3 (BCR-) - N23-4 (BCR+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
M20-3 (BCL-) - M20-4 (BCL+) 1 MΩ or higher




OK

9.CHECK FLOOR WIRE (TO B+)

NG

REPAIR OR REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (TO B+)
U189145E02
1.531,2.417 1.646,2.417 1.646,2.417 1.646,0.875 false 1.615,4.104 1.771,3.771 false 2.219,4.031 1.875,3.771 false 1.708,1.333 3.156,2.021 1.448,0.688 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.104,1.333 1.448,1.865 1.344,0.531 10 false Rear Airbag Sensor (for Front Passenger Side) 2.24,0.74 2.365,0.896 0.125,0.156 10 false A 1.854,0.5 1.979,0.656 0.125,0.156 10 false B 1.49,0.479 1.615,0.635 0.125,0.156 10 false C 1.094,0.729 1.219,0.885 0.125,0.156 10 false D 1.26,2.792 2.115,2.958 0.854,0.167 10 false Connector C 0.219,2.604 1.031,2.771 0.813,0.167 10 false Floor Wire*2 0.219,2.323 1.417,2.49 1.198,0.167 10 false Floor No. 2 Wire*1 0.063,3.896 0.792,4.063 0.729,0.167 10 false *1: for LHD 0.063,4.188 0.792,4.354 0.729,0.167 10 false *2: for RHD 0.688,3.635 0.99,3.781 0.302,0.146 10 false M20 0.688,3.344 0.99,3.49 0.302,0.146 10 false N23 1.094,3.333 1.26,3.5 0.167,0.167 10 false *1 1.094,3.615 1.271,3.781 0.177,0.167 10 false *2 1.344,4.281 1.844,4.438 0.5,0.156 10 false BCL-*2 2.25,4.135 2.802,4.292 0.552,0.156 10 false BCL+*2 1.344,4.115 1.844,4.271 0.5,0.156 10 false BCR-*1 2.25,3.979 2.802,4.135 0.552,0.156 10 false BCR+*1

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
N23-3 (BBR-) - Body ground Below 1 V
N23-4 (BBR+) - Body ground

for RHD:
Tester Connection Specified Condition
M20-3 (BBL-) - Body ground Below 1 V
M20-4 (BBL+) - Body ground




OK

10.CHECK FLOOR WIRE (TO GROUND)

NG

REPAIR OR REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (TO GROUND)
U189145E02
1.531,2.417 1.646,2.417 1.646,2.417 1.646,0.875 false 1.615,4.104 1.771,3.771 false 2.219,4.031 1.875,3.771 false 1.708,1.333 3.156,2.021 1.448,0.688 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.104,1.333 1.448,1.865 1.344,0.531 10 false Rear Airbag Sensor (for Front Passenger Side) 2.24,0.74 2.365,0.896 0.125,0.156 10 false A 1.854,0.5 1.979,0.656 0.125,0.156 10 false B 1.49,0.479 1.615,0.635 0.125,0.156 10 false C 1.094,0.729 1.219,0.885 0.125,0.156 10 false D 1.26,2.792 2.115,2.958 0.854,0.167 10 false Connector C 0.219,2.604 1.031,2.771 0.813,0.167 10 false Floor Wire*2 0.219,2.323 1.417,2.49 1.198,0.167 10 false Floor No. 2 Wire*1 0.063,3.896 0.792,4.063 0.729,0.167 10 false *1: for LHD 0.063,4.188 0.792,4.354 0.729,0.167 10 false *2: for RHD 0.688,3.635 0.99,3.781 0.302,0.146 10 false M20 0.688,3.344 0.99,3.49 0.302,0.146 10 false N23 1.094,3.333 1.26,3.5 0.167,0.167 10 false *1 1.094,3.615 1.271,3.781 0.177,0.167 10 false *2 1.344,4.281 1.844,4.438 0.5,0.156 10 false BCL-*2 2.25,4.135 2.802,4.292 0.552,0.156 10 false BCL+*2 1.344,4.115 1.844,4.271 0.5,0.156 10 false BCR-*1 2.25,3.979 2.802,4.135 0.552,0.156 10 false BCR+*1

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
N23-3 (BCR-) - Body ground 1 MΩ or higher
N23-4 (BCR+) - Body ground

for RHD:
Tester Connection Specified Condition
M20-3 (BCL-) - Body ground 1 MΩ or higher
N20-4 (BCL+) - Body ground




OK

11.CHECK WIRE HARNESS (OPEN)

NG

REPAIR OR REPLACE FLOOR WIRE

11.CHECK WIRE HARNESS (OPEN)
C364218E08
0.083,3.25 0.5,3.5 0.417,0.25 1.583,2.917 2,3.167 0.417,0.25 0.083,2.917 0.5,3.167 0.417,0.25 1.583,3.25 2,3.5 0.417,0.25 0.896,3.969 1,3.688 true 1.198,3.938 1.083,3.688 true 2.781,4.115 2.448,3.708 true 2.219,4.115 2.365,3.688 true 2.365,4.552 1.979,4.552 1.979,4.552 1.979,4.063 false 0.906,0.792 1.219,0.99 0.313,0.198 10 false F 1.26,0.583 1.573,0.781 0.313,0.198 10 false E 1.594,0.573 1.906,0.771 0.313,0.198 10 false D 1.74,0.573 2.052,0.771 0.313,0.198 10 false C 2.063,0.573 2.375,0.771 0.313,0.198 10 false B 2.448,0.813 2.76,1.01 0.313,0.198 10 false A 1.958,1.396 3.396,1.927 1.438,0.531 10 false Rear Airbag Sensor (for Front Passenger Side) 0.188,1.406 1.542,2.052 1.354,0.646 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 0.708,2.823 1.688,3.073 0.979,0.25 10 false Connector E 0.188,3.292 0.5,3.49 0.313,0.198 10 false L10 0.542,4.115 1.083,4.333 0.542,0.219 10 false BDL-*2 1.146,3.969 1.688,4.188 0.542,0.219 10 false BDR+*1 1.667,3.292 1.979,3.49 0.313,0.198 10 false M20 2.417,4.458 3.24,4.656 0.823,0.198 10 false Service Wire 2.229,2.823 3.208,3.073 0.979,0.25 10 false Connector B 0.531,3.958 1.031,4.198 0.5,0.24 10 false BDR-*1 1.156,4.125 1.771,4.365 0.615,0.24 10 false BDL+*2 0.177,2.969 0.49,3.167 0.313,0.198 10 false K10 1.656,2.958 1.969,3.156 0.313,0.198 10 false N23 0.531,2.948 0.844,3.146 0.313,0.198 10 false *1 0.521,3.26 0.833,3.458 0.313,0.198 10 false *2 2.052,2.948 2.365,3.146 0.313,0.198 10 false *1 2.031,3.26 2.344,3.458 0.313,0.198 10 false *2 0.083,4.385 0.854,4.667 0.771,0.281 10 false *1: for LHD 0.917,4.385 1.688,4.667 0.771,0.281 10 false *2: for RHD 2.031,4.125 2.531,4.365 0.5,0.24 10 false BDR-*1 2.031,4.271 2.573,4.49 0.542,0.219 10 false BDL-*2 2.677,4.104 3.219,4.323 0.542,0.219 10 false BDR+*1 2.677,4.25 3.292,4.49 0.615,0.24 10 false BDL+*2

a.

Disconnect the connectors from the side rear airbag sensor (for front passenger side) and the front passenger side - side airbag sensor (for rear side).


b.

for LHD:

Using a service wire, connect terminals N23-1 (BDR+) and N23-2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting them.



c.

for RHD:

Using a service wire, connect terminals M20-1 (BDL+) and M20-2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting them.



d.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - K10-4 (BDR+) Below 1 Ω

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - L10-4 (BDL+) Below 1 Ω




OK

12.CHECK WIRE HARNESS (SHORT)

NG

18.CHECK DOOR WIRE (OPEN)
12.CHECK WIRE HARNESS (SHORT)
U189156E02
1.729,3.729 1.906,3.833 0.177,0.104 1.677,4.167 1.76,3.771 false 2.281,3.896 1.865,3.781 false 1.896,1.333 3.344,1.917 1.448,0.583 10 false Rear Airbag Sensor (for Front Passenger Side) 0.125,1.323 1.26,1.99 1.135,0.667 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 2.5,0.719 2.625,0.875 0.125,0.156 10 false A 2.083,0.49 2.208,0.646 0.125,0.156 10 false B 1.74,0.5 1.865,0.656 0.125,0.156 10 false C 1.604,0.51 1.729,0.667 0.125,0.156 10 false D 1.25,0.51 1.375,0.667 0.125,0.156 10 false E 0.844,0.74 0.969,0.896 0.125,0.156 10 false F 1.271,2.708 2.104,2.885 0.833,0.177 10 false Connector E 0.042,3.885 0.771,4.052 0.729,0.167 10 false *1: for LHD 0.042,4.198 0.771,4.365 0.729,0.167 10 false *2: for RHD 1.427,4.188 1.948,4.365 0.521,0.177 10 false BDR-*1 2.333,3.865 2.875,4.042 0.542,0.177 10 false BDR+*1 1.427,4.344 1.948,4.521 0.521,0.177 10 false BDL-*2 2.333,4.031 2.875,4.208 0.542,0.177 10 false BDL+*2 0.813,3.208 1.083,3.385 0.271,0.177 10 false K10 0.823,3.563 1.094,3.74 0.271,0.177 10 false L10 1.188,3.229 1.354,3.385 0.167,0.156 10 false *1 1.188,3.573 1.354,3.729 0.167,0.156 10 false *2

a.

Disconnect the service wire from connector B.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - K10-4 (BDR+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - L10-4 (BDL+) 1 MΩ or higher




OK

13.CHECK WIRE HARNESS (TO B+)

NG

19.CHECK DOOR WIRE (SHORT)
13.CHECK WIRE HARNESS (TO B+)
U189156E02
1.729,3.729 1.906,3.833 0.177,0.104 1.677,4.167 1.76,3.771 false 2.281,3.896 1.865,3.781 false 1.896,1.333 3.344,1.917 1.448,0.583 10 false Rear Airbag Sensor (for Front Passenger Side) 0.125,1.323 1.26,1.99 1.135,0.667 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 2.5,0.719 2.625,0.875 0.125,0.156 10 false A 2.083,0.49 2.208,0.646 0.125,0.156 10 false B 1.74,0.5 1.865,0.656 0.125,0.156 10 false C 1.604,0.51 1.729,0.667 0.125,0.156 10 false D 1.25,0.51 1.375,0.667 0.125,0.156 10 false E 0.844,0.74 0.969,0.896 0.125,0.156 10 false F 1.271,2.708 2.104,2.885 0.833,0.177 10 false Connector E 0.042,3.885 0.771,4.052 0.729,0.167 10 false *1: for LHD 0.042,4.198 0.771,4.365 0.729,0.167 10 false *2: for RHD 1.427,4.188 1.948,4.365 0.521,0.177 10 false BDR-*1 2.333,3.865 2.875,4.042 0.542,0.177 10 false BDR+*1 1.427,4.344 1.948,4.521 0.521,0.177 10 false BDL-*2 2.333,4.031 2.875,4.208 0.542,0.177 10 false BDL+*2 0.813,3.208 1.083,3.385 0.271,0.177 10 false K10 0.823,3.563 1.094,3.74 0.271,0.177 10 false L10 1.188,3.229 1.354,3.385 0.167,0.156 10 false *1 1.188,3.573 1.354,3.729 0.167,0.156 10 false *2

a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch on (IG).


c.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - Body ground Below 1 V
K10-4 (BDR+) - Body ground

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - Body ground Below 1 V
L10-4 (BDL+) - Body ground




OK

14.CHECK WIRE HARNESS (TO GROUND)

NG

20.CHECK DOOR WIRE (TO B+)
14.CHECK WIRE HARNESS (TO GROUND)
U189156E02
1.729,3.729 1.906,3.833 0.177,0.104 1.677,4.167 1.76,3.771 false 2.281,3.896 1.865,3.781 false 1.896,1.333 3.344,1.917 1.448,0.583 10 false Rear Airbag Sensor (for Front Passenger Side) 0.125,1.323 1.26,1.99 1.135,0.667 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 2.5,0.719 2.625,0.875 0.125,0.156 10 false A 2.083,0.49 2.208,0.646 0.125,0.156 10 false B 1.74,0.5 1.865,0.656 0.125,0.156 10 false C 1.604,0.51 1.729,0.667 0.125,0.156 10 false D 1.25,0.51 1.375,0.667 0.125,0.156 10 false E 0.844,0.74 0.969,0.896 0.125,0.156 10 false F 1.271,2.708 2.104,2.885 0.833,0.177 10 false Connector E 0.042,3.885 0.771,4.052 0.729,0.167 10 false *1: for LHD 0.042,4.198 0.771,4.365 0.729,0.167 10 false *2: for RHD 1.427,4.188 1.948,4.365 0.521,0.177 10 false BDR-*1 2.333,3.865 2.875,4.042 0.542,0.177 10 false BDR+*1 1.427,4.344 1.948,4.521 0.521,0.177 10 false BDL-*2 2.333,4.031 2.875,4.208 0.542,0.177 10 false BDL+*2 0.813,3.208 1.083,3.385 0.271,0.177 10 false K10 0.823,3.563 1.094,3.74 0.271,0.177 10 false L10 1.188,3.229 1.354,3.385 0.167,0.156 10 false *1 1.188,3.573 1.354,3.729 0.167,0.156 10 false *2

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - Body ground 1 MΩ or higher
K10-4 (BDR+) - Body ground

for LHD:
Tester Connection Specified Condition
L10-3 (BDL-) - Body ground 1 MΩ or higher
L10-4 (BDL+) - Body ground




OK

15.CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Front Side)

NG

21.CHECK DOOR WIRE (TO GROUND)
15.CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Front Side)
C135372E23
0.365,4.052 0.521,3.667 true 0.792,4.052 0.625,3.854 true 1.302,0.583 1.125,0.104 1.125,0.104 1.323,0.104 false 2.115,1.708 3.01,2.042 0.896,0.333 10 false Center Airbag Sensor 0.042,1.854 1.24,2.396 1.198,0.542 10 false Driver Side - Side Airbag Sensor (for Front Side) 1.385,0.031 2.823,0.354 1.438,0.323 10 false Rear Airbag Sensor (for Front Passenger Side) 0.333,4.26 0.74,4.417 0.406,0.156 10 false DLC3 0.26,4.052 0.49,4.208 0.229,0.156 10 false CG 0.677,4.052 0.906,4.208 0.229,0.156 10 false TC 2.083,2.479 2.583,2.656 0.5,0.177 10 false DTC 81 2.083,3.688 2.583,3.865 0.5,0.177 10 false DTC 82

a.

Connect the connectors to the center airbag sensor.


b.

Interchange the front passenger side - side airbag sensor (for front side) with the driver side - side airbag sensor (for front side) and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692/81 and B1697/82 are not output A
DTC B1697/82 is output B
DTC B1692/81 is output C

HINT:

DTCs other than B1692/81 and B1697/82 may be output at this time, but they are not related to this check.




A

16.CHECK REAR AIRBAG SENSOR (for Front Passenger Side)

B

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C

REPLACE FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Front Side)

16.CHECK REAR AIRBAG SENSOR (for Front Passenger Side)
C135372E24
0.406,4.042 0.531,3.667 true 0.75,4.042 0.625,3.854 true 2.198,1.75 3.104,2.094 0.906,0.344 10 false Center Airbag Sensor 0.198,1.865 1.281,2.583 1.083,0.719 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 0.385,4.281 0.792,4.458 0.406,0.177 10 false DLC3 0.281,4.042 0.521,4.219 0.24,0.177 10 false CG 0.635,4.042 0.875,4.219 0.24,0.177 10 false TC 2.115,3.677 2.635,3.833 0.521,0.156 10 false DTC 82 2.125,2.531 2.646,2.688 0.521,0.156 10 false DTC 81 0.646,0.094 2.938,0.271 2.292,0.177 10 false Rear Airbag Sensor (for Driver Side)

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the rear airbag sensor (for front passenger side) with the rear airbag sensor (for driver side) and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


i.

Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692/81 and B1697/82 are not output A
DTC B1697/82 is output B
DTC B1692/81 is output C

HINT:

DTCs other than DTC B1692/81 and B1697/82 may be output at this time, but they are not related to this check.




A

17.CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Rear Side)

B

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C

REPLACE REAR AIRBAG SENSOR (for Front Passenger Side)

17.CHECK FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Rear Side)
C366248E01
1.708,0.417 1.708,0.094 1.708,0.094 1.615,0.094 false 2.469,1.115 1.896,0.125 1.896,0.125 2.156,0.125 false 0.313,4.031 0.521,3.667 false 0.76,4.042 0.604,3.844 false 0.073,0.021 1.583,0.49 1.51,0.469 10 false Driver Side - Side Airbag Sensor (for Rear Side) 2.229,0.052 3.375,0.75 1.146,0.698 10 false Front Passenger Side - Side Airbag Sensor (for Front Side) 2.156,2.458 2.75,2.667 0.594,0.208 10 false DTC 81 0.083,1.885 1.365,2.427 1.281,0.542 10 false Rear Airbag Sensor (for Front Passenger Side) 0.208,4.042 0.667,4.24 0.458,0.198 10 false CG 0.729,4.063 1.188,4.26 0.458,0.198 10 false TC 0.375,4.25 0.833,4.448 0.458,0.198 10 false DLC3 2.125,3.677 2.719,3.885 0.594,0.208 10 false DTC 82

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the front passenger side - side airbag sensor (for rear side) with the driver side - side airbag sensor (for rear side) and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG), and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch on (IG), and wait for at least 60 seconds.


i.

Check the DTCs (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1692/81 and B1697/82 are not output A
DTC B1697/82 is output B
DTC B1692/81 is output C

HINT:

DTCs other than DTC B1692/81 and B1697/82 may be output at this time, but they are not related to this check.




A

USE SIMULATION METHOD TO CHECK

B

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

C

REPLACE FRONT PASSENGER SIDE - SIDE AIRBAG SENSOR ASSEMBLY (for Rear Side)

18.CHECK DOOR WIRE (OPEN)
C364219E08
0.083,3 0.5,3.25 0.417,0.25 1.458,3.333 1.875,3.583 0.417,0.25 0.083,3.333 0.5,3.583 0.417,0.25 1.458,3 1.875,3.25 0.417,0.25 1.427,2.208 1.635,2.208 1.635,2.208 1.448,0.802 false 1.927,2.083 1.781,2.083 1.781,2.083 1.938,0.802 false 0.771,4.021 0.979,3.781 true 1.229,4.01 1.063,3.771 true 2.417,4.25 2.417,4.104 false 0.792,0.646 1.104,0.844 0.313,0.198 10 false F 1.167,0.438 1.479,0.635 0.313,0.198 10 false E 1.51,0.427 1.823,0.625 0.313,0.198 10 false D 1.76,0.427 2.073,0.625 0.313,0.198 10 false C 2.094,0.427 2.406,0.625 0.313,0.198 10 false B 2.479,0.656 2.792,0.854 0.313,0.198 10 false A 1.938,1.24 3.375,1.708 1.438,0.469 10 false Rear Airbag Sensor (for Front Passenger Side) 0.052,1.24 1.5,1.823 1.448,0.583 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 0.385,2.125 1.448,2.375 1.063,0.25 10 false Door Wire LH*1 2,2 3.115,2.26 1.115,0.26 10 false Floor Wire*1 0.5,2.771 1.563,3.01 1.063,0.24 10 false Connector E 0.177,3.375 0.49,3.573 0.313,0.198 10 false L10 1.531,3.375 1.844,3.573 0.313,0.198 10 false LM3 1.125,4.01 1.698,4.24 0.573,0.229 10 false BDR+*1 2.146,4.26 3.094,4.49 0.948,0.229 10 false Service Wire 2.021,2.771 3.083,3.01 1.063,0.24 10 false Connector D 0.448,4.021 0.948,4.25 0.5,0.229 10 false BDR-*1 1.531,3.042 1.844,3.24 0.313,0.198 10 false KN3 0.167,3.031 0.479,3.229 0.313,0.198 10 false K10 0.531,3 1.031,3.229 0.5,0.229 10 false *1 0.521,3.281 1.021,3.51 0.5,0.229 10 false *2 1.917,3.01 2.417,3.24 0.5,0.229 10 false *1 1.896,3.333 2.396,3.563 0.5,0.229 10 false *2 2.01,2.281 3.25,2.531 1.24,0.25 10 false Floor No. 2 Wire*2 0.396,2.385 1.458,2.635 1.063,0.25 10 false Door Wire RH*2 0.052,4.417 0.906,4.656 0.854,0.24 10 false *1: for LHD 0.448,4.156 0.948,4.385 0.5,0.229 10 false BDL-*1 1.135,4.156 1.708,4.385 0.573,0.229 10 false BDL+*1 0.875,4.417 1.729,4.656 0.854,0.24 10 false *2: for RHD

a.

Disconnect the door wire connector from the floor wire.


b.

for LHD:

Using a service wire, connect terminals KN3-1 and KN3-2 of connector D.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting of them.



c.

for RHD:

Using a service wire, connect terminals LM3-1 and LM3-2 of connector D.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting of them.



d.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - K10-4 (BDR+) Below 1 Ω

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - L10-4 (BDL+) Below 1 Ω




OK

REPAIR OR REPLACE FLOOR WIRE

NG

REPAIR OR REPLACE DOOR WIRE

19.CHECK DOOR WIRE (SHORT)
U189169E02
1.708,4.094 1.771,3.76 false 2.219,3.969 1.875,3.771 false 2.052,0.875 2.052,2.427 false 2.552,0.75 2.688,0.896 0.135,0.146 10 false A 2.146,0.49 2.281,0.635 0.135,0.146 10 false B 1.792,0.5 1.927,0.646 0.135,0.146 10 false C 1.552,0.5 1.688,0.646 0.135,0.146 10 false D 1.188,0.51 1.323,0.656 0.135,0.146 10 false E 0.802,0.74 0.938,0.885 0.135,0.146 10 false F 2.156,1.323 3.25,1.833 1.094,0.51 10 false Rear Airbag Sensor (for Front Passenger Side) 0.073,1.333 1.563,1.844 1.49,0.51 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 0.083,3.927 0.813,4.094 0.729,0.167 10 false *1: for LHD 0.083,4.271 0.813,4.438 0.729,0.167 10 false *2: for RHD 2.115,3.167 2.948,3.333 0.833,0.167 10 false Connector E 1.396,4.115 1.896,4.292 0.5,0.177 10 false BDR-*1 2.281,3.958 2.865,4.135 0.583,0.177 10 false BDR+*1 1.396,4.281 1.896,4.458 0.5,0.177 10 false BDL-*2 2.281,4.125 2.865,4.302 0.583,0.177 10 false BDL+*2 0.698,3.344 0.969,3.49 0.271,0.146 10 false K10 0.708,3.646 0.979,3.792 0.271,0.146 10 false L10 1.104,3.333 1.313,3.51 0.208,0.177 10 false *1 1.115,3.635 1.323,3.813 0.208,0.177 10 false *2 1.99,2.448 2.781,2.625 0.792,0.177 10 false Floor Wire*1 1.99,2.708 3.177,2.885 1.188,0.177 10 false Floor No. 2 Wire*2 0.479,2.406 1.552,2.583 1.073,0.177 10 false Door Wire LH*1 0.479,2.656 1.531,2.833 1.052,0.177 10 false Door Wire RH*2

a.

Disconnect the door wire connector from the floor wire.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - K10-4 (BDR+) 1 MΩ or higher

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - L10-4 (BDL+) 1 MΩ or higher




OK

REPAIR OR REPLACE FLOOR WIRE

NG

REPAIR OR REPLACE DOOR WIRE

20.CHECK DOOR WIRE (TO B+)
U189169E02
1.708,4.094 1.771,3.76 false 2.219,3.969 1.875,3.771 false 2.052,0.875 2.052,2.427 false 2.552,0.75 2.688,0.896 0.135,0.146 10 false A 2.146,0.49 2.281,0.635 0.135,0.146 10 false B 1.792,0.5 1.927,0.646 0.135,0.146 10 false C 1.552,0.5 1.688,0.646 0.135,0.146 10 false D 1.188,0.51 1.323,0.656 0.135,0.146 10 false E 0.802,0.74 0.938,0.885 0.135,0.146 10 false F 2.156,1.323 3.25,1.833 1.094,0.51 10 false Rear Airbag Sensor (for Front Passenger Side) 0.073,1.333 1.563,1.844 1.49,0.51 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 0.083,3.927 0.813,4.094 0.729,0.167 10 false *1: for LHD 0.083,4.271 0.813,4.438 0.729,0.167 10 false *2: for RHD 2.115,3.167 2.948,3.333 0.833,0.167 10 false Connector E 1.396,4.115 1.896,4.292 0.5,0.177 10 false BDR-*1 2.281,3.958 2.865,4.135 0.583,0.177 10 false BDR+*1 1.396,4.281 1.896,4.458 0.5,0.177 10 false BDL-*2 2.281,4.125 2.865,4.302 0.583,0.177 10 false BDL+*2 0.698,3.344 0.969,3.49 0.271,0.146 10 false K10 0.708,3.646 0.979,3.792 0.271,0.146 10 false L10 1.104,3.333 1.313,3.51 0.208,0.177 10 false *1 1.115,3.635 1.323,3.813 0.208,0.177 10 false *2 1.99,2.448 2.781,2.625 0.792,0.177 10 false Floor Wire*1 1.99,2.708 3.177,2.885 1.188,0.177 10 false Floor No. 2 Wire*2 0.479,2.406 1.552,2.583 1.073,0.177 10 false Door Wire LH*1 0.479,2.656 1.531,2.833 1.052,0.177 10 false Door Wire RH*2

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the door wire connector from the floor wire.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch on (IG).


f.

Measure the voltage of the wire harness side connector.

Standard voltage:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - Body ground Below 1 V
K10-4 (BDR+) - Body ground

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - Body ground Below 1 V
L10-4 (BDL+) - Body ground




OK

REPAIR OR REPLACE FLOOR WIRE

NG

REPAIR OR REPLACE DOOR WIRE

21.CHECK DOOR WIRE (TO GROUND)
U189169E02
1.708,4.094 1.771,3.76 false 2.219,3.969 1.875,3.771 false 2.052,0.875 2.052,2.427 false 2.552,0.75 2.688,0.896 0.135,0.146 10 false A 2.146,0.49 2.281,0.635 0.135,0.146 10 false B 1.792,0.5 1.927,0.646 0.135,0.146 10 false C 1.552,0.5 1.688,0.646 0.135,0.146 10 false D 1.188,0.51 1.323,0.656 0.135,0.146 10 false E 0.802,0.74 0.938,0.885 0.135,0.146 10 false F 2.156,1.323 3.25,1.833 1.094,0.51 10 false Rear Airbag Sensor (for Front Passenger Side) 0.073,1.333 1.563,1.844 1.49,0.51 10 false Front Passenger Side - Side Airbag Sensor (for Rear Side) 0.083,3.927 0.813,4.094 0.729,0.167 10 false *1: for LHD 0.083,4.271 0.813,4.438 0.729,0.167 10 false *2: for RHD 2.115,3.167 2.948,3.333 0.833,0.167 10 false Connector E 1.396,4.115 1.896,4.292 0.5,0.177 10 false BDR-*1 2.281,3.958 2.865,4.135 0.583,0.177 10 false BDR+*1 1.396,4.281 1.896,4.458 0.5,0.177 10 false BDL-*2 2.281,4.125 2.865,4.302 0.583,0.177 10 false BDL+*2 0.698,3.344 0.969,3.49 0.271,0.146 10 false K10 0.708,3.646 0.979,3.792 0.271,0.146 10 false L10 1.104,3.333 1.313,3.51 0.208,0.177 10 false *1 1.115,3.635 1.323,3.813 0.208,0.177 10 false *2 1.99,2.448 2.781,2.625 0.792,0.177 10 false Floor Wire*1 1.99,2.708 3.177,2.885 1.188,0.177 10 false Floor No. 2 Wire*2 0.479,2.406 1.552,2.583 1.073,0.177 10 false Door Wire LH*1 0.479,2.656 1.531,2.833 1.052,0.177 10 false Door Wire RH*2

a.

Disconnect the door wire connector from the floor wire.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
for LHD:
Tester Connection Specified Condition
K10-3 (BDR-) - Body ground 1 MΩ or higher
K10-4 (BDR+) - Body ground

for RHD:
Tester Connection Specified Condition
L10-3 (BDL-) - Body ground 1 MΩ or higher
L10-4 (BDL+) - Body ground




OK

REPAIR OR REPLACE FLOOR WIRE

NG

REPAIR OR REPLACE DOOR WIRE