Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1622/81  Lost communication with Side Airbag Sensor RH  B1623/81  Side Airbag Sensor Assembly RH Initialization Incomplete  B1632/81  Lost Communication with Rear Airbag Sensor RH  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1642/81  Lost Communication with Side Satellite Sensor Bus RH  B1643/81  Side Satellite Sensor Bus RH Initialization Incomplete  B1673/81  Lost Communication with Rear Door Side Airbag Sensor RH  B1674/81  Rear Door Side Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The side collision sensor RH circuit (bus 1) consists of the center airbag sensor assembly, side airbag sensor RH (for Front Side), side airbag sensor RH (for Rear Side) and rear airbag sensor RH.

The side airbag sensor RH (for Front Side), side airbag sensor RH (for Rear Side) and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbags should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 1).

DTC No. DTC Detection Condition Trouble Area
B1622/81
B1623/81
B1632/81
B1633/81
B1642/81
B1643/81
B1673/81
B1674/81
·

The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 1).

·

Side airbag sensor RH (for Front Side) malfunction

·

Side airbag sensor RH (for Rear Side) malfunction

·

Rear airbag sensor RH malfunction

·

Center airbag sensor assembly malfunction


·

No. 2 floor wire

·

Rear door wire RH

·

Side airbag sensor RH (for Front Side)

·

Side airbag sensor RH (for Rear Side)

·

Rear airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

C238366E93
3.427,4.667 3.969,5.083 0.542,0.417 10 false N32 3.427,4.844 4.875,5.219 1.448,0.375 10 false Rear Airbag Sensor RH 0.552,4.844 2.094,5.313 1.542,0.469 10 false Side Airbag Sensor RH (for Rear Side) 5.521,4.854 6.875,5.25 1.354,0.396 10 false Center Airbag Sensor Assembly 5.521,4.688 5.958,5.063 0.438,0.375 10 false N9 1.167,0.521 1.969,1.083 0.802,0.563 10 false BBR+ 1.594,0.438 2.063,0.938 0.469,0.5 10 false 4 1.167,1.104 1.802,1.604 0.635,0.5 10 false BBR- 5.323,0.438 5.792,1.01 0.469,0.573 10 false 8 5.323,1 5.99,1.427 0.667,0.427 10 false 11 1.594,1.01 1.948,1.448 0.354,0.438 10 false 3 1.125,3.792 1.927,4.427 0.802,0.635 10 false BDR+ 2.417,3.594 2.865,4.198 0.448,0.604 10 false 1 1.167,4.354 1.792,4.833 0.625,0.479 10 false BDR- 2.417,4.146 2.771,4.563 0.354,0.417 10 false 2 2.365,3.813 3.021,4.375 0.656,0.563 10 false KN3 2.365,4.354 2.917,4.875 0.552,0.521 10 false KN3 0.552,4.667 1.146,5.073 0.594,0.406 10 false K14 0.542,2.792 2.135,3.281 1.594,0.49 10 false Side Airbag Sensor RH (for Front Side) 0.542,2.625 1.115,3.094 0.573,0.469 10 false N31 3.469,3.802 4.063,4.292 0.594,0.49 10 false BDR+ 3.469,4.333 4.01,4.865 0.542,0.531 10 false BDR- 3.479,1.698 4.063,2.146 0.583,0.448 10 false BCR+ 3.469,2.302 4.031,2.729 0.563,0.427 10 false BCR- 1.167,1.688 1.729,2.083 0.563,0.396 10 false BCR+ 1.167,2.302 1.833,2.792 0.667,0.49 10 false BCR- 5.563,0.542 6.135,1 0.573,0.458 10 false BBR+ 5.563,1.115 6.021,1.656 0.458,0.542 10 false BBR- 1.594,1.604 2.063,2.271 0.469,0.667 10 false 1 1.594,2.208 2.083,2.688 0.49,0.479 10 false 2 3.292,1.604 3.75,2.073 0.458,0.469 10 false 4 3.292,2.177 3.875,2.74 0.583,0.563 10 false 3 3.313,3.698 3.771,4.135 0.458,0.438 10 false 1 3.313,4.24 3.802,4.792 0.49,0.552 10 false 2 1.594,3.698 2.021,4.323 0.427,0.625 10 false 2 1.594,4.24 2.021,4.813 0.427,0.573 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1623, B1642, B1643 or 81 is output. A
Current DTC B1633 is output. B
Current DTC B1673 or B1674 is output. C
Current DTC B1622 is output. D
Current DTC B1632 is output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the engine switch off and then on (IG) again.

·

Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1643, B1673, B1674 and 81 may be output at this time, but they are not related to this check.





A

2.CHECK HISTORY DTC

B

19.CHECK HISTORY DTC

C

27.CHECK CONNECTORS

D

38.CHECK SIDE AIRBAG SENSOR RH (for Front Side)

E

39.CHECK REAR AIRBAG SENSOR RH
2.CHECK HISTORY DTC
HINT:

If DTC B1642, B1643 or 81 was output, skip this step and proceed to step 3.


a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1622 is not output. A
History DTC B1622 is output. B


HINT:

Codes other than history DTC B1622 may be output at this time, but they are not related to this check.




A

3.CHECK CONNECTORS

B

38.CHECK SIDE AIRBAG SENSOR RH (for Front Side)
3.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor RH (for Front Side), rear airbag sensor RH and side airbag sensor RH (for Rear Side). Also check that the connectors that link the No. 2 floor wire and rear door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the center airbag sensor assembly, side airbag sensor RH (for Front Side), rear airbag sensor RH and side airbag sensor RH (for Rear Side). Also disconnect the connectors that link the No. 2 floor wire and rear door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

4.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U189546E01
1.006,2.448 1.127,2.600 0.121,0.153 10 D 1.32,2.448 1.440,2.600 0.121,0.153 10 C 1.777,2.448 1.897,2.600 0.121,0.153 10 B 2.091,2.448 2.212,2.600 0.121,0.153 10 A 0.706,2.448 0.864,2.628 0.159,0.181 10 *1 2.57,2.129 2.729,2.281 0.159,0.152 10 *2 0.803,0.188 0.978,0.349 0.175,0.161 10 *a 0.383,3.202 0.584,3.377 0.200,0.175 10 *b 1.285,1.124 1.637,1.282 0.352,0.158 10 BBR- 2.249,1.124 2.640,1.282 0.392,0.158 10 BBR+ 1.216,0.519 1.504,0.676 0.288,0.158 10 N9 0.568,3.643 0.858,3.801 0.290,0.158 10 N31 1.942,4.221 2.338,4.379 0.396,0.158 10 BBR+ 1.058,4.221 1.418,4.379 0.360,0.158 10 BBR- 1.761,3.772 2.139,4.207 false 1.657,3.772 1.279,4.207 false 1.246,1.897 1.423,2.063 0.177,0.166 10 *3 1.602,2.466 1.602,1.977 1.602,1.977 1.449,1.977 false 1.86,0.846 1.495,1.115 false 2.092,0.622 2.449,1.115 false 1.999,1.052 1.999,1.228 false 1.908,1.24 2.067,1.392 0.159,0.152 10 *4

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-4 (BBR+) - N31-3 (BBR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

5.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U189547E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 N31 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-4 (BBR+) - N31-3 (BBR-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

6.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U189547E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 N31 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N31-4 (BBR+) - Body ground Engine switch on (IG) Below 1 V
N31-3 (BBR-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

7.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

7.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U189547E01
0.955,0.93 1.076,1.083 0.121,0.153 10 D 1.271,0.93 1.392,1.083 0.121,0.153 10 C 1.72,0.93 1.841,1.083 0.121,0.153 10 B 2.041,0.93 2.162,1.083 0.121,0.153 10 A 0.641,0.93 0.793,1.111 0.151,0.181 10 *1 2.437,0.64 2.641,0.792 0.204,0.152 10 *2 1.131,0.259 1.310,0.412 0.179,0.152 10 *3 0.334,1.749 0.568,1.925 0.234,0.175 10 *a 0.458,2.306 0.747,2.464 0.289,0.158 10 N31 1.027,2.844 1.383,3.002 0.356,0.158 10 BBR- 1.716,2.844 2.115,3.002 0.399,0.158 10 BBR+ 1.507,2.453 1.263,2.825 false 1.685,2.453 1.929,2.825 false 1.555,0.943 1.555,0.346 1.555,0.346 1.327,0.346 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-4 (BBR+) - Body ground Always 1 MΩ or higher
N31-3 (BBR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

8.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U189559E01
1.173,2.317 1.294,2.470 0.121,0.153 10 D 1.483,2.317 1.604,2.470 0.121,0.153 10 C 1.836,2.317 1.957,2.470 0.121,0.153 10 B 2.15,2.317 2.270,2.470 0.121,0.153 10 A 0.754,2.317 0.923,2.468 0.169,0.150 10 *1 0.641,0.146 0.840,0.318 0.199,0.172 10 *a 0.357,3.207 0.538,3.361 0.181,0.154 10 *b 0.969,4.066 1.344,4.224 0.376,0.158 10 BCR- 1.814,4.066 2.211,4.224 0.397,0.158 10 BCR+ 0.501,3.578 0.790,3.735 0.289,0.158 10 N32 0.892,0.572 1.184,0.730 0.291,0.158 10 N31 2.11,1.071 2.482,1.228 0.372,0.158 10 BCR- 1.229,1.071 1.636,1.228 0.407,0.158 10 BCR+ 1.82,0.698 1.484,1.046 false 1.975,0.698 2.312,1.046 false 1.331,1.773 1.489,1.926 0.158,0.153 10 *3 2.448,2.317 2.624,2.486 0.176,0.169 10 *2 1.715,2.331 1.715,1.853 1.715,1.853 1.537,1.853 false 1.524,3.673 1.195,4.049 false 1.693,3.673 2.022,4.049 false 1.609,4.024 1.609,4.299 false 1.52,4.305 1.679,4.458 0.158,0.153 10 *4

Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - N31-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

9.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U189548E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.175,2.317 1.468,2.474 0.293,0.158 10 N31 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - N31-2 (BCR-) Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

10.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U189548E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.175,2.317 1.468,2.474 0.293,0.158 10 N31 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - Body ground Engine switch on (IG) Below 1 V
N31-2 (BCR-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

11.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

11.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U189548E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.175,2.317 1.468,2.474 0.293,0.158 10 N31 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - Body ground Always 1 MΩ or higher
N31-2 (BCR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

12.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (OPEN)
a.
U189773E02
1.552,3.719 1.26,4.115 false 1.729,3.719 2.021,4.115 false 1.771,0.781 1.521,0.271 false 1.927,0.781 2.177,0.271 false 1.865,1.25 1.865,1.344 1.865,1.344 2.26,1.344 false 1.563,2.313 1.688,2.469 0.125,0.156 10 false D 1.729,2.313 1.854,2.469 0.125,0.156 10 false C 2.073,2.313 2.198,2.469 0.125,0.156 10 false B 2.375,2.313 2.5,2.469 0.125,0.156 10 false A 2.688,2.292 2.875,2.469 0.188,0.177 10 false *2 0.49,2.292 0.708,2.479 0.219,0.188 10 false *1 0.344,3.146 0.552,3.354 0.208,0.208 10 false *b 0.625,0.167 0.813,0.396 0.188,0.229 10 false *a 1.021,4.135 1.396,4.292 0.375,0.156 10 false BDR- 1.844,4.135 2.25,4.292 0.406,0.156 10 false BDR+ 0.469,3.542 0.74,3.698 0.271,0.156 10 false K14 0.823,0.688 1.115,0.844 0.292,0.156 10 false N32 2.229,0.167 2.594,0.323 0.365,0.156 10 false BDR- 1.073,0.167 1.479,0.323 0.406,0.156 10 false BDR+ 0.917,2.313 1.042,2.469 0.125,0.156 10 false F 1.219,2.313 1.344,2.469 0.125,0.156 10 false E 2.281,1.25 2.438,1.427 0.156,0.177 10 false *3

Connect the connectors that link the No. 2 floor wire and rear door wire RH.


b.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - K14-1 (BDR-) Always Below 1 Ω


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

13.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT)

NG

34.CHECK NO. 2 FLOOR WIRE (OPEN)
13.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT)
a.
U189760E02
1.729,2.292 1.344,2.729 false 1.896,2.292 2.292,2.729 false 1.583,0.667 1.708,0.823 0.125,0.156 10 false D 1.729,0.667 1.854,0.823 0.125,0.156 10 false C 2.083,0.677 2.208,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.625,2.177 0.917,2.333 0.292,0.156 10 false K14 2.083,2.75 2.5,2.927 0.417,0.177 10 false BDR+ 1.083,2.74 1.49,2.896 0.406,0.156 10 false BDR- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.667 1.354,0.823 0.125,0.156 10 false E

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - K14-1 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

14.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO B+)

NG

35.CHECK NO. 2 FLOOR WIRE (SHORT)
14.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO B+)
a.
U189760E02
1.729,2.292 1.344,2.729 false 1.896,2.292 2.292,2.729 false 1.583,0.667 1.708,0.823 0.125,0.156 10 false D 1.729,0.667 1.854,0.823 0.125,0.156 10 false C 2.083,0.677 2.208,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.625,2.177 0.917,2.333 0.292,0.156 10 false K14 2.083,2.75 2.5,2.927 0.417,0.177 10 false BDR+ 1.083,2.74 1.49,2.896 0.406,0.156 10 false BDR- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.667 1.354,0.823 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - Body ground Engine switch on (IG) Below 1 V
K14-1 (BDR-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

15.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO GROUND)

NG

36.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
15.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO GROUND)
a.
U189760E02
1.729,2.292 1.344,2.729 false 1.896,2.292 2.292,2.729 false 1.583,0.667 1.708,0.823 0.125,0.156 10 false D 1.729,0.667 1.854,0.823 0.125,0.156 10 false C 2.083,0.677 2.208,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.625,2.177 0.917,2.333 0.292,0.156 10 false K14 2.083,2.75 2.5,2.927 0.417,0.177 10 false BDR+ 1.083,2.74 1.49,2.896 0.406,0.156 10 false BDR- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.667 1.354,0.823 0.125,0.156 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - Body ground Always 1 MΩ or higher
K14-1 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

16.CHECK SIDE AIRBAG SENSOR RH (for Front Side)

NG

37.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
16.CHECK SIDE AIRBAG SENSOR RH (for Front Side)
a.
C238218E03
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Connect the connectors to the rear airbag sensor RH, side airbag sensor RH (for Rear Side) and center airbag sensor assembly.


b.

Interchange the side airbag sensor RH (for Front Side) with LH (for Front Side) and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
for Current DTC B1623:
Result Proceed to
DTC B1623 is output. A
DTC B1628 is output. C
DTCs B1623 and B1628 are not output. D

for Current DTC B1642, B1643 or 81:
Result Proceed to
DTC B1642, B1643 or 81 is output. B
DTC B1647, B1648 or 82 is output. C
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. D


HINT:

Codes other than DTCs B1623, B1628, B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor RH (for Front Side) and LH (for Front Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly



A

B

17.CHECK REAR AIRBAG SENSOR RH

C

D

17.CHECK REAR AIRBAG SENSOR RH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the rear airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor RH (for Front Side)



A

18.CHECK SIDE AIRBAG SENSOR RH (for Rear Side)

B

C

18.CHECK SIDE AIRBAG SENSOR RH (for Rear Side)
a.
C238395E09
0.698,0.938 0.875,1.115 0.177,0.177 10 false *1 2.552,0.938 2.729,1.115 0.177,0.177 10 false *2 2.25,0.99 2.375,1.188 0.125,0.198 10 false A 2.094,0.99 2.219,1.188 0.125,0.198 10 false B 1.74,0.99 1.865,1.188 0.125,0.198 10 false C 1.583,0.99 1.708,1.188 0.125,0.198 10 false D 1.25,1 1.375,1.198 0.125,0.198 10 false E 1.094,1 1.219,1.198 0.125,0.198 10 false F

Interchange the side airbag sensor RH (for Rear Side) with LH (for Rear Side) and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1642, B1643 or 81 is output. A
DTC B1647, B1648 or 82 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the side airbag sensor RH (for Rear Side) and LH (for Rear Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor RH



A

B

C

19.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1632 is not output. A
History DTC B1632 is output. B


HINT:

Codes other than history DTC B1632 may be output at this time, but they are not related to this check.




A

20.CHECK CONNECTORS

B

39.CHECK REAR AIRBAG SENSOR RH
20.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor RH (for Front Side) and rear airbag sensor RH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor RH (for Front Side) and rear airbag sensor RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

21.CHECK NO. 2 FLOOR WIRE (OPEN)

NG

REPLACE NO. 2 FLOOR WIRE

21.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U189559E01
1.173,2.317 1.294,2.470 0.121,0.153 10 D 1.483,2.317 1.604,2.470 0.121,0.153 10 C 1.836,2.317 1.957,2.470 0.121,0.153 10 B 2.15,2.317 2.270,2.470 0.121,0.153 10 A 0.754,2.317 0.923,2.468 0.169,0.150 10 *1 0.641,0.146 0.840,0.318 0.199,0.172 10 *a 0.357,3.207 0.538,3.361 0.181,0.154 10 *b 0.969,4.066 1.344,4.224 0.376,0.158 10 BCR- 1.814,4.066 2.211,4.224 0.397,0.158 10 BCR+ 0.501,3.578 0.790,3.735 0.289,0.158 10 N32 0.892,0.572 1.184,0.730 0.291,0.158 10 N31 2.11,1.071 2.482,1.228 0.372,0.158 10 BCR- 1.229,1.071 1.636,1.228 0.407,0.158 10 BCR+ 1.82,0.698 1.484,1.046 false 1.975,0.698 2.312,1.046 false 1.331,1.773 1.489,1.926 0.158,0.153 10 *3 2.448,2.317 2.624,2.486 0.176,0.169 10 *2 1.715,2.331 1.715,1.853 1.715,1.853 1.537,1.853 false 1.524,3.673 1.195,4.049 false 1.693,3.673 2.022,4.049 false 1.609,4.024 1.609,4.299 false 1.52,4.305 1.679,4.458 0.158,0.153 10 *4

Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - N31-2 (BCR-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))
*b Front view of wire harness connector
(to Rear Airbag Sensor RH)



OK

22.CHECK NO. 2 FLOOR WIRE (SHORT)

NG

REPLACE NO. 2 FLOOR WIRE

22.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U189548E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.175,2.317 1.468,2.474 0.293,0.158 10 N31 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - N31-2 (BCR-) Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)

NG

REPLACE NO. 2 FLOOR WIRE

23.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U189548E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.175,2.317 1.468,2.474 0.293,0.158 10 N31 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - Body ground Engine switch on (IG) Below 1 V
N31-2 (BCR-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE NO. 2 FLOOR WIRE

24.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U189548E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.175,2.317 1.468,2.474 0.293,0.158 10 N31 2.278,2.865 2.666,3.023 0.387,0.158 10 BCR- 1.595,2.865 1.991,3.023 0.396,0.158 10 BCR+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N31-1 (BCR+) - Body ground Always 1 MΩ or higher
N31-2 (BCR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor RH (for Front Side)
*3 No. 2 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Front Side))



OK

25.CHECK SIDE AIRBAG SENSOR RH (for Front Side)

NG

REPLACE NO. 2 FLOOR WIRE

25.CHECK SIDE AIRBAG SENSOR RH (for Front Side)
a.
C238218E03
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Connect the connector to the rear airbag sensor RH.


b.

Interchange the side airbag sensor RH (for Front Side) with LH (for Front Side) and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor RH (for Front Side) and LH (for Front Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly



A

26.CHECK REAR AIRBAG SENSOR RH

B

C

26.CHECK REAR AIRBAG SENSOR RH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the rear airbag sensor RH with LH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1633 is output. A
DTC B1638 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor RH (for Front Side)



A

C

C

27.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear airbag sensor RH and side airbag sensor RH (for Rear Side). Also check that the connectors that link the No. 2 floor wire and rear door wire RH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear airbag sensor RH and side airbag sensor RH (for Rear Side). Also disconnect the connectors that link the No. 2 floor wire and rear door wire RH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

28.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (OPEN)

NG

REPLACE WIRE HARNESS

28.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (OPEN)
a.
U189773E02
1.552,3.719 1.26,4.115 false 1.729,3.719 2.021,4.115 false 1.771,0.781 1.521,0.271 false 1.927,0.781 2.177,0.271 false 1.865,1.25 1.865,1.344 1.865,1.344 2.26,1.344 false 1.563,2.313 1.688,2.469 0.125,0.156 10 false D 1.729,2.313 1.854,2.469 0.125,0.156 10 false C 2.073,2.313 2.198,2.469 0.125,0.156 10 false B 2.375,2.313 2.5,2.469 0.125,0.156 10 false A 2.688,2.292 2.875,2.469 0.188,0.177 10 false *2 0.49,2.292 0.708,2.479 0.219,0.188 10 false *1 0.344,3.146 0.552,3.354 0.208,0.208 10 false *b 0.625,0.167 0.813,0.396 0.188,0.229 10 false *a 1.021,4.135 1.396,4.292 0.375,0.156 10 false BDR- 1.844,4.135 2.25,4.292 0.406,0.156 10 false BDR+ 0.469,3.542 0.74,3.698 0.271,0.156 10 false K14 0.823,0.688 1.115,0.844 0.292,0.156 10 false N32 2.229,0.167 2.594,0.323 0.365,0.156 10 false BDR- 1.073,0.167 1.479,0.323 0.406,0.156 10 false BDR+ 0.917,2.313 1.042,2.469 0.125,0.156 10 false F 1.219,2.313 1.344,2.469 0.125,0.156 10 false E 2.281,1.25 2.438,1.427 0.156,0.177 10 false *3

Connect the connectors that link the No. 2 floor wire and rear door wire RH.


b.

Using a service wire, connect terminals 1 (BDR+) and 2 (BDR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - K14-1 (BDR-) Always Below 1 Ω


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

29.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT)

NG

34.CHECK NO. 2 FLOOR WIRE (OPEN)
29.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT)
a.
U189760E02
1.729,2.292 1.344,2.729 false 1.896,2.292 2.292,2.729 false 1.583,0.667 1.708,0.823 0.125,0.156 10 false D 1.729,0.667 1.854,0.823 0.125,0.156 10 false C 2.083,0.677 2.208,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.625,2.177 0.917,2.333 0.292,0.156 10 false K14 2.083,2.75 2.5,2.927 0.417,0.177 10 false BDR+ 1.083,2.74 1.49,2.896 0.406,0.156 10 false BDR- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.667 1.354,0.823 0.125,0.156 10 false E

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - K14-1 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

30.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO B+)

NG

35.CHECK NO. 2 FLOOR WIRE (SHORT)
30.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO B+)
a.
U189760E02
1.729,2.292 1.344,2.729 false 1.896,2.292 2.292,2.729 false 1.583,0.667 1.708,0.823 0.125,0.156 10 false D 1.729,0.667 1.854,0.823 0.125,0.156 10 false C 2.083,0.677 2.208,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.625,2.177 0.917,2.333 0.292,0.156 10 false K14 2.083,2.75 2.5,2.927 0.417,0.177 10 false BDR+ 1.083,2.74 1.49,2.896 0.406,0.156 10 false BDR- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.667 1.354,0.823 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - Body ground Engine switch on (IG) Below 1 V
K14-1 (BDR-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

31.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO GROUND)

NG

36.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
31.CHECK SIDE AIRBAG SENSOR RH CIRCUIT (for Rear Side) (SHORT TO GROUND)
a.
U189760E02
1.729,2.292 1.344,2.729 false 1.896,2.292 2.292,2.729 false 1.583,0.667 1.708,0.823 0.125,0.156 10 false D 1.729,0.667 1.854,0.823 0.125,0.156 10 false C 2.083,0.677 2.208,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.625,2.177 0.917,2.333 0.292,0.156 10 false K14 2.083,2.75 2.5,2.927 0.417,0.177 10 false BDR+ 1.083,2.74 1.49,2.896 0.406,0.156 10 false BDR- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.667 1.354,0.823 0.125,0.156 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K14-2 (BDR+) - Body ground Always 1 MΩ or higher
K14-1 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*a Front view of wire harness connector
(to Side Airbag Sensor RH (for Rear Side))



OK

32.CHECK REAR AIRBAG SENSOR RH

NG

37.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
32.CHECK REAR AIRBAG SENSOR RH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Connect the connector to the side airbag sensor RH (for Rear Side).


b.

Interchange the rear airbag sensor RH with LH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1673 or B1674 is output. A
DTC B1684 or B1689 is output. B
DTCs B1673, B1674, B1684 and B1689 are not output. C


HINT:

Codes other than DTCs B1673, B1674, B1684 and B1689 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor RH (for Front Side)



A

33.CHECK SIDE AIRBAG SENSOR RH (for Rear Side)

B

C

33.CHECK SIDE AIRBAG SENSOR RH (for Rear Side)
a.
C238395E09
0.698,0.938 0.875,1.115 0.177,0.177 10 false *1 2.552,0.938 2.729,1.115 0.177,0.177 10 false *2 2.25,0.99 2.375,1.188 0.125,0.198 10 false A 2.094,0.99 2.219,1.188 0.125,0.198 10 false B 1.74,0.99 1.865,1.188 0.125,0.198 10 false C 1.583,0.99 1.708,1.188 0.125,0.198 10 false D 1.25,1 1.375,1.198 0.125,0.198 10 false E 1.094,1 1.219,1.198 0.125,0.198 10 false F

Interchange the side airbag sensor RH (for Rear Side) with LH (for Rear Side) and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1673 or B1674 is output. A
DTC B1684 or B1689 is output. B
DTCs B1673, B1674, B1684 and B1689 are not output. C


HINT:

Codes other than DTCs B1673, B1674, B1684 and B1689 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the side airbag sensor RH (for Rear Side) and LH (for Rear Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor RH



A

B

C

34.CHECK NO. 2 FLOOR WIRE (OPEN)
a.
U189602E02
1.688,3.615 1.365,3.292 true 1.927,3.604 2.25,3.281 true 2.052,0.844 1.771,0.438 true 2.188,0.854 2.458,0.448 true 2.115,1.25 2.115,1.385 2.115,1.385 2.427,1.385 false 1.323,2.385 1.323,2.615 false 2.135,2.24 2.135,1.885 2.135,1.885 1.917,1.885 false 2.281,3.167 2.688,3.333 0.406,0.167 10 false BDR+ 1,3.156 1.354,3.323 0.354,0.167 10 false BDR- 2.51,0.344 2.896,0.51 0.385,0.167 10 false BDR- 1.344,0.344 1.74,0.51 0.396,0.167 10 false BDR+ 0.771,3.708 1.073,3.865 0.302,0.156 10 false KN3 1.188,0.771 1.479,0.927 0.292,0.156 10 false N32 1.021,0.229 1.177,0.396 0.156,0.167 10 false *a 0.583,3 0.76,3.167 0.177,0.167 10 false *b 2.458,1.302 2.635,1.469 0.177,0.167 10 false *5 0.365,2.219 0.531,2.385 0.167,0.167 10 false *1 0.688,2.219 0.792,2.385 0.104,0.167 10 false F 1.052,2.219 1.167,2.385 0.115,0.167 10 false E 1.49,2.219 1.604,2.385 0.115,0.167 10 false D 1.854,2.219 1.969,2.385 0.115,0.167 10 false C 2.313,2.219 2.427,2.385 0.115,0.167 10 false B 2.677,2.219 2.792,2.385 0.115,0.167 10 false A 2.927,2.219 3.094,2.385 0.167,0.167 10 false *2 1.229,2.625 1.406,2.792 0.177,0.167 10 false *3 1.719,1.813 1.875,1.979 0.156,0.167 10 false *4

Disconnect the rear door wire RH connector from the No. 2 floor wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
KN3-1 (BDR+) - KN3-2 (BDR-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*3 Rear Door Wire RH
*4 No. 2 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor RH)
*b Front view of wire harness connector
(to Rear Door Wire RH)



OK

REPLACE REAR DOOR WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

35.CHECK NO. 2 FLOOR WIRE (SHORT)
a.
U189600E02
1.51,2.375 1.26,2.063 false 1.719,2.365 1.969,2.052 false 1.344,0.927 1.344,1.156 false 2.073,0.813 2.073,0.469 2.073,0.469 1.854,0.469 false 2.021,1.927 2.427,2.094 0.406,0.167 10 false BDR+ 0.875,1.927 1.229,2.094 0.354,0.167 10 false BDR- 0.677,2.427 0.979,2.583 0.302,0.156 10 false KN3 0.49,1.813 0.667,1.979 0.177,0.167 10 false *a 0.406,0.719 0.573,0.885 0.167,0.167 10 false *1 0.792,0.781 0.896,0.948 0.104,0.167 10 false F 1.094,0.771 1.208,0.938 0.115,0.167 10 false E 1.5,0.771 1.615,0.938 0.115,0.167 10 false D 1.813,0.771 1.927,0.938 0.115,0.167 10 false C 2.219,0.771 2.333,0.938 0.115,0.167 10 false B 2.531,0.771 2.646,0.938 0.115,0.167 10 false A 2.813,0.781 2.979,0.948 0.167,0.167 10 false *2 1.26,1.177 1.438,1.344 0.177,0.167 10 false *3 1.667,0.365 1.823,0.531 0.156,0.167 10 false *4

Disconnect the rear door wire RH connector from the No. 2 floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
KN3-1 (BDR+) - KN3-2 (BDR-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*3 Rear Door Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Rear Door Wire RH)



OK

REPLACE REAR DOOR WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

36.CHECK NO. 2 FLOOR WIRE (SHORT TO B+)
a.
U189600E02
1.51,2.375 1.26,2.063 false 1.719,2.365 1.969,2.052 false 1.344,0.927 1.344,1.156 false 2.073,0.813 2.073,0.469 2.073,0.469 1.854,0.469 false 2.021,1.927 2.427,2.094 0.406,0.167 10 false BDR+ 0.875,1.927 1.229,2.094 0.354,0.167 10 false BDR- 0.677,2.427 0.979,2.583 0.302,0.156 10 false KN3 0.49,1.813 0.667,1.979 0.177,0.167 10 false *a 0.406,0.719 0.573,0.885 0.167,0.167 10 false *1 0.792,0.781 0.896,0.948 0.104,0.167 10 false F 1.094,0.771 1.208,0.938 0.115,0.167 10 false E 1.5,0.771 1.615,0.938 0.115,0.167 10 false D 1.813,0.771 1.927,0.938 0.115,0.167 10 false C 2.219,0.771 2.333,0.938 0.115,0.167 10 false B 2.531,0.771 2.646,0.938 0.115,0.167 10 false A 2.813,0.781 2.979,0.948 0.167,0.167 10 false *2 1.26,1.177 1.438,1.344 0.177,0.167 10 false *3 1.667,0.365 1.823,0.531 0.156,0.167 10 false *4

Disconnect the rear door wire RH connector from the No. 2 floor wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
KN3-1 (BDR+) - Body ground Engine switch on (IG) Below 1 V
KN3-2 (BDR-) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*3 Rear Door Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Rear Door Wire RH)



OK

REPLACE REAR DOOR WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

37.CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)
a.
U189600E02
1.51,2.375 1.26,2.063 false 1.719,2.365 1.969,2.052 false 1.344,0.927 1.344,1.156 false 2.073,0.813 2.073,0.469 2.073,0.469 1.854,0.469 false 2.021,1.927 2.427,2.094 0.406,0.167 10 false BDR+ 0.875,1.927 1.229,2.094 0.354,0.167 10 false BDR- 0.677,2.427 0.979,2.583 0.302,0.156 10 false KN3 0.49,1.813 0.667,1.979 0.177,0.167 10 false *a 0.406,0.719 0.573,0.885 0.167,0.167 10 false *1 0.792,0.781 0.896,0.948 0.104,0.167 10 false F 1.094,0.771 1.208,0.938 0.115,0.167 10 false E 1.5,0.771 1.615,0.938 0.115,0.167 10 false D 1.813,0.771 1.927,0.938 0.115,0.167 10 false C 2.219,0.771 2.333,0.938 0.115,0.167 10 false B 2.531,0.771 2.646,0.938 0.115,0.167 10 false A 2.813,0.781 2.979,0.948 0.167,0.167 10 false *2 1.26,1.177 1.438,1.344 0.177,0.167 10 false *3 1.667,0.365 1.823,0.531 0.156,0.167 10 false *4

Disconnect the rear door wire RH connector from the No. 2 floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
KN3-1 (BDR+) - Body ground Always 1 MΩ or higher
KN3-2 (BDR-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor RH
*3 Rear Door Wire RH
*4 No. 2 Floor Wire
*a Front view of wire harness connector
(to Rear Door Wire RH)



OK

REPLACE REAR DOOR WIRE RH

NG

REPLACE NO. 2 FLOOR WIRE

38.CHECK SIDE AIRBAG SENSOR RH (for Front Side)
a.
C238218E03
0.793,1.142 0.979,1.302 0.186,0.159 10 *1 2.307,0.855 2.493,1.014 0.186,0.159 10 *2 1.718,1.142 1.861,1.293 0.143,0.151 10 B 1.873,1.142 2.016,1.293 0.143,0.151 10 A 1.257,1.142 1.400,1.293 0.143,0.151 10 C 1.1,1.142 1.243,1.293 0.143,0.151 10 D

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor RH (for Front Side) with LH (for Front Side) and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1622 is output. A
DTC B1627 is output. B
DTCs B1622 and B1627 are not output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor RH (for Front Side) and LH (for Front Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly



A

B

C

39.CHECK REAR AIRBAG SENSOR RH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the rear airbag sensor RH with LH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1632 is output. A
DTC B1637 is output. B
DTCs B1632 and B1637 are not output. C


HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor RH (for Front Side)



A

B

C