Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1627/82  Lost communication with Side Airbag Sensor LH  B1628/82  Side Airbag Sensor Assembly LH Initialization Incomplete  B1637/82  Lost Communication with Rear Airbag Sensor LH  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  B1647/82  Lost Communication with Side Satellite Sensor Bus LH  B1648/82  Side Satellite Sensor Bus LH Initialization Incomplete  B1684/82  Lost Communication with Rear Door Side Airbag Sensor LH  B1689/82  Rear Door Side Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (bus 1) consists of the center airbag sensor assembly, side airbag sensor LH (for Front Side), side airbag sensor LH (for Rear Side) and rear airbag sensor LH.

The side airbag sensor LH (for Front Side), side airbag sensor LH (for Rear Side) and rear airbag sensor LH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbags should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 1).

DTC No. DTC Detection Condition Trouble Area
B1627/82
B1628/82
B1637/82
B1638/82
B1647/82
B1648/82
B1684/82
B1689/82
·

The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 1).

·

Side airbag sensor LH (for Front Side) malfunction

·

Side airbag sensor LH (for Rear Side) malfunction

·

Rear airbag sensor LH malfunction

·

Center airbag sensor assembly malfunction


·

Floor wire

·

Rear door wire LH

·

Side airbag sensor LH (for Front Side)

·

Side airbag sensor LH (for Rear Side)

·

Rear airbag sensor LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C238366E94
3.438,4.667 3.896,4.99 0.458,0.323 10 false M34 3.438,4.833 4.844,5.052 1.406,0.219 10 false Rear Airbag Sensor LH 0.563,4.854 2.01,5.271 1.448,0.417 10 false Side Airbag Sensor LH (for Rear Side) 5.542,4.865 6.698,5.271 1.156,0.406 10 false Center Airbag Sensor Assembly 5.542,4.698 5.927,5.052 0.385,0.354 10 false N9 1.156,0.521 1.75,0.917 0.594,0.396 10 false BBL+ 1.594,0.438 1.896,0.813 0.302,0.375 10 false 4 1.167,1.094 1.781,1.5 0.615,0.406 10 false BBL- 5.323,0.438 5.677,0.875 0.354,0.438 10 false 8 5.281,0.99 5.688,1.573 0.406,0.583 10 false 15 1.594,1.021 1.927,1.375 0.333,0.354 10 false 3 1.156,3.781 1.854,4.198 0.698,0.417 10 false BDL+ 2.417,3.594 2.771,4.052 0.354,0.458 10 false 1 1.167,4.323 1.771,4.688 0.604,0.365 10 false BDL- 2.438,4.135 2.781,4.677 0.344,0.542 10 false 2 2.344,3.802 2.917,4.344 0.573,0.542 10 false LM3 2.354,4.344 2.896,4.927 0.542,0.583 10 false LM3 0.563,4.667 1.094,5.094 0.531,0.427 10 false L14 0.563,2.802 2.021,3.365 1.458,0.563 10 false Side Airbag Sensor LH (for Front Side) 0.563,2.625 1.052,3.021 0.49,0.396 10 false M33 3.479,3.792 4.01,4.292 0.531,0.5 10 false BDL+ 3.479,4.333 3.969,4.688 0.49,0.354 10 false BDL- 3.479,1.698 3.979,2.083 0.5,0.385 10 false BCL+ 3.479,2.302 3.917,2.708 0.438,0.406 10 false BCL- 1.167,1.688 1.76,2.125 0.594,0.438 10 false BCL+ 1.167,2.292 1.781,2.698 0.615,0.406 10 false BCL- 5.573,0.531 6.063,0.906 0.49,0.375 10 false BBL+ 5.573,1.115 6.042,1.521 0.469,0.406 10 false BBL- 1.594,1.604 1.823,2.021 0.229,0.417 10 false 1 1.594,2.208 2.021,2.719 0.427,0.51 10 false 2 3.292,1.604 3.604,2.167 0.313,0.563 10 false 4 3.292,2.198 3.552,2.646 0.26,0.448 10 false 3 3.292,3.688 3.698,4.177 0.406,0.49 10 false 1 3.292,4.24 3.625,4.729 0.333,0.49 10 false 2 1.594,3.698 1.906,4.167 0.313,0.469 10 false 2 1.594,4.229 1.854,4.625 0.26,0.396 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CURRENT DTC
a.

Check for current DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Current DTC B1628, B1647, B1648 or 82 is output. A
Current DTC B1638 is output. B
Current DTC B1684 or B1689 is output. C
Current DTC B1627 is output. D
Current DTC B1637 is output. E


HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the engine switch off and then on (IG) again.

·

Codes other than current DTCs B1627, B1628, B1637, B1638, B1647, B1648, B1684, B1689 and 82 may be output at this time, but they are not related to this check.





A

2.CHECK HISTORY DTC

B

19.CHECK HISTORY DTC

C

27.CHECK CONNECTORS

D

38.CHECK SIDE AIRBAG SENSOR LH (for Front Side)

E

39.CHECK REAR AIRBAG SENSOR LH
2.CHECK HISTORY DTC
HINT:

If DTC B1647, B1648 or 82 was output, skip this step and proceed to step 3.


a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1627 is not output. A
History DTC B1627 is output. B


HINT:

Codes other than history DTC B1627 may be output at this time, but they are not related to this check.




A

3.CHECK CONNECTORS

B

38.CHECK SIDE AIRBAG SENSOR LH (for Front Side)
3.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the center airbag sensor assembly, side airbag sensor LH (for Front Side), rear airbag sensor LH and side airbag sensor LH (for Rear Side). Also check that the connectors that link the floor wire and rear door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the center airbag sensor assembly, side airbag sensor LH (for Front Side), rear airbag sensor LH and side airbag sensor LH (for Rear Side). Also disconnect the connectors that link the floor wire and rear door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

4.CHECK FLOOR WIRE (OPEN)

NG

REPLACE WIRE HARNESS

4.CHECK FLOOR WIRE (OPEN)
a.
U189550E02
2.01,1.104 2.01,1.292 false 1.938,0.667 1.49,1.146 true 2.167,0.885 2.51,1.146 true 1.531,2.271 1.531,1.792 1.531,1.792 1.365,1.792 false 1.521,3.75 1.198,4.135 true 1.656,3.75 1.979,4.135 true 0.75,0.271 0.917,0.458 0.167,0.188 10 false *a 1.281,1.177 1.677,1.333 0.396,0.156 10 false BBL+ 2.354,1.177 2.719,1.333 0.365,0.156 10 false BBL- 1.063,0.594 1.281,0.75 0.219,0.156 10 false M9 1.927,1.302 2.083,1.5 0.156,0.198 10 false *4 0.948,2.24 1.073,2.396 0.125,0.156 10 false D 1.26,2.24 1.385,2.396 0.125,0.156 10 false C 1.719,2.24 1.844,2.396 0.125,0.156 10 false B 2.021,2.24 2.146,2.396 0.125,0.156 10 false A 0.625,2.24 0.813,2.427 0.188,0.188 10 false *1 2.438,2.24 2.646,2.438 0.208,0.198 10 false *2 1.177,1.688 1.354,1.885 0.177,0.198 10 false *3 0.302,3.156 0.479,3.354 0.177,0.198 10 false *b 0.448,3.625 0.74,3.781 0.292,0.156 10 false M33 1.802,4.146 2.188,4.302 0.385,0.156 10 false BBL+ 1.01,4.146 1.365,4.302 0.354,0.156 10 false BBL-

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-4 (BBL+) - M33-3 (BBL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

5.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT)
a.
U189551E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.451,2.301 0.741,2.458 0.290,0.158 10 M33 1.872,2.83 2.269,2.987 0.397,0.158 10 BBL+ 0.994,2.83 1.363,2.987 0.369,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.75,0.188 1.907,0.334 0.158,0.147 10 *3 1.569,0.73 1.569,0.272 1.569,0.272 1.722,0.272 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-4 (BBL+) - M33-3 (BBL-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

6.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

6.CHECK FLOOR WIRE (SHORT TO B+)
a.
U189551E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.451,2.301 0.741,2.458 0.290,0.158 10 M33 1.872,2.83 2.269,2.987 0.397,0.158 10 BBL+ 0.994,2.83 1.363,2.987 0.369,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.75,0.188 1.907,0.334 0.158,0.147 10 *3 1.569,0.73 1.569,0.272 1.569,0.272 1.722,0.272 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-4 (BBL+) - Body ground Engine switch on (IG) Below 1 V
M33-3 (BBL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

7.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

7.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U189551E01
0.97,0.712 1.091,0.865 0.121,0.153 10 D 1.286,0.712 1.406,0.865 0.121,0.153 10 C 1.739,0.712 1.860,0.865 0.121,0.153 10 B 2.056,0.712 2.177,0.865 0.121,0.153 10 A 0.668,0.712 0.845,0.925 0.176,0.213 10 *1 2.44,0.712 2.639,0.892 0.198,0.180 10 *2 0.345,1.827 0.552,2.007 0.208,0.180 10 *a 0.451,2.301 0.741,2.458 0.290,0.158 10 M33 1.872,2.83 2.269,2.987 0.397,0.158 10 BBL+ 0.994,2.83 1.363,2.987 0.369,0.158 10 BBL- 1.539,2.451 1.194,2.797 false 1.68,2.451 2.026,2.797 false 1.75,0.188 1.907,0.334 0.158,0.147 10 *3 1.569,0.73 1.569,0.272 1.569,0.272 1.722,0.272 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-4 (BBL+) - Body ground Always 1 MΩ or higher
M33-3 (BBL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Front Side)
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

8.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

8.CHECK FLOOR WIRE (OPEN)
a.
U189560E01
1.173,2.317 1.294,2.470 0.121,0.153 10 D 1.483,2.317 1.604,2.470 0.121,0.153 10 C 1.836,2.317 1.957,2.470 0.121,0.153 10 B 2.15,2.317 2.270,2.470 0.121,0.153 10 A 0.754,2.317 0.923,2.468 0.169,0.150 10 *1 0.641,0.146 0.840,0.318 0.199,0.172 10 *a 0.357,3.207 0.538,3.361 0.181,0.154 10 *b 0.983,4.066 1.359,4.224 0.376,0.158 10 BCL- 1.843,4.066 2.240,4.224 0.397,0.158 10 BCL+ 0.491,3.578 0.780,3.735 0.289,0.158 10 M34 0.881,0.572 1.172,0.730 0.291,0.158 10 M33 2.154,1.071 2.526,1.228 0.372,0.158 10 BCL- 1.273,1.071 1.680,1.228 0.407,0.158 10 BCL+ 1.82,0.698 1.484,1.046 false 1.975,0.698 2.312,1.046 false 1.331,1.773 1.489,1.926 0.158,0.153 10 *3 2.448,2.317 2.624,2.486 0.176,0.169 10 *2 1.715,2.331 1.715,1.853 1.715,1.853 1.537,1.853 false 1.524,3.673 1.195,4.049 false 1.693,3.673 2.022,4.049 false 1.609,4.024 1.609,4.299 false 1.52,4.305 1.679,4.458 0.158,0.153 10 *4

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - M33-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)



OK

9.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

9.CHECK FLOOR WIRE (SHORT)
a.
U189549E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.165,2.317 1.458,2.474 0.293,0.158 10 M33 2.337,2.865 2.724,3.023 0.387,0.158 10 BCL- 1.654,2.865 2.050,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - M33-2 (BCL-) Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

10.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

10.CHECK FLOOR WIRE (SHORT TO B+)
a.
U189549E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.165,2.317 1.458,2.474 0.293,0.158 10 M33 2.337,2.865 2.724,3.023 0.387,0.158 10 BCL- 1.654,2.865 2.050,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
M33-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

11.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

11.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U189549E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.165,2.317 1.458,2.474 0.293,0.158 10 M33 2.337,2.865 2.724,3.023 0.387,0.158 10 BCL- 1.654,2.865 2.050,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - Body ground Always 1 MΩ or higher
M33-2 (BCL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

12.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (OPEN)

NG

REPLACE FLOOR WIRE

12.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (OPEN)
a.
U189774E02
1.573,3.719 1.281,4.115 false 1.719,3.719 2.01,4.115 false 1.75,0.792 1.5,0.281 false 1.927,0.802 2.177,0.292 false 1.865,1.26 1.865,1.354 1.865,1.354 2.26,1.354 false 1.563,2.292 1.688,2.448 0.125,0.156 10 false D 1.729,2.292 1.854,2.448 0.125,0.156 10 false C 2.073,2.292 2.198,2.448 0.125,0.156 10 false B 2.375,2.292 2.5,2.448 0.125,0.156 10 false A 2.688,2.292 2.875,2.469 0.188,0.177 10 false *2 0.49,2.292 0.708,2.479 0.219,0.188 10 false *1 0.344,3.146 0.552,3.354 0.208,0.208 10 false *b 0.625,0.167 0.813,0.396 0.188,0.229 10 false *a 1.021,4.135 1.396,4.292 0.375,0.156 10 false BDL- 1.844,4.135 2.25,4.292 0.406,0.156 10 false BDL+ 0.5,3.552 0.771,3.708 0.271,0.156 10 false L14 0.792,0.667 1.083,0.823 0.292,0.156 10 false M34 2.219,0.188 2.583,0.344 0.365,0.156 10 false BDL- 1.063,0.188 1.469,0.344 0.406,0.156 10 false BDL+ 0.917,2.292 1.042,2.448 0.125,0.156 10 false F 1.219,2.292 1.344,2.448 0.125,0.156 10 false E 2.281,1.26 2.438,1.438 0.156,0.177 10 false *3

Connect the connectors that link the floor wire and rear door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - L14-1 (BDL-) Always Below 1 Ω


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

13.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT)

NG

34.CHECK FLOOR WIRE (OPEN)
13.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT)
a.
U189761E02
1.729,2.281 1.344,2.719 false 1.896,2.292 2.292,2.729 false 1.583,0.677 1.708,0.833 0.125,0.156 10 false D 1.729,0.677 1.854,0.833 0.125,0.156 10 false C 2.073,0.677 2.198,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.635,2.177 0.927,2.333 0.292,0.156 10 false L14 2.135,2.729 2.552,2.906 0.417,0.177 10 false BDL+ 1.135,2.729 1.542,2.885 0.406,0.156 10 false BDL- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.677 1.354,0.833 0.125,0.156 10 false E

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - L14-1 (BDL-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

14.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO B+)

NG

35.CHECK FLOOR WIRE (SHORT)
14.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO B+)
a.
U189761E02
1.729,2.281 1.344,2.719 false 1.896,2.292 2.292,2.729 false 1.583,0.677 1.708,0.833 0.125,0.156 10 false D 1.729,0.677 1.854,0.833 0.125,0.156 10 false C 2.073,0.677 2.198,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.635,2.177 0.927,2.333 0.292,0.156 10 false L14 2.135,2.729 2.552,2.906 0.417,0.177 10 false BDL+ 1.135,2.729 1.542,2.885 0.406,0.156 10 false BDL- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.677 1.354,0.833 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - Body ground Engine switch on (IG) Below 1 V
L14-1 (BDL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

15.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO GROUND)

NG

36.CHECK FLOOR WIRE (SHORT TO B+)
15.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO GROUND)
a.
U189761E02
1.729,2.281 1.344,2.719 false 1.896,2.292 2.292,2.729 false 1.583,0.677 1.708,0.833 0.125,0.156 10 false D 1.729,0.677 1.854,0.833 0.125,0.156 10 false C 2.073,0.677 2.198,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.635,2.177 0.927,2.333 0.292,0.156 10 false L14 2.135,2.729 2.552,2.906 0.417,0.177 10 false BDL+ 1.135,2.729 1.542,2.885 0.406,0.156 10 false BDL- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.677 1.354,0.833 0.125,0.156 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - Body ground Always 1 MΩ or higher
L14-1 (BDL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

16.CHECK SIDE AIRBAG SENSOR LH (for Front Side)

NG

37.CHECK FLOOR WIRE (SHORT TO GROUND)
16.CHECK SIDE AIRBAG SENSOR LH (for Front Side)
a.
C238224E05
0.792,1.01 0.938,1.198 0.146,0.188 10 false *1 2.313,1.01 2.521,1.198 0.208,0.188 10 false *2 1.875,1.01 2,1.198 0.125,0.188 10 false A 1.708,1.01 1.833,1.198 0.125,0.188 10 false B 1.271,1.01 1.396,1.198 0.125,0.188 10 false C 1.115,1.01 1.24,1.198 0.125,0.188 10 false D

Connect the connectors to the rear airbag sensor LH, side airbag sensor LH (for Rear Side) and center airbag sensor assembly.


b.

Interchange the side airbag sensor LH (for Front Side) with RH (for Front Side) and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
for Current DTC B1628:
Result Proceed to
DTC B1628 is output. A
DTC B1623 is output. C
DTCs B1623 and B1628 are not output. D

for Current DTC B1647, B1648 or 82:
Result Proceed to
DTC B1647, B1648 or 82 is output. B
DTC B1642, B1643 or 81 is output. C
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. D


HINT:

Codes other than DTCs B1623, B1628, B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor LH (for Front Side) and RH (for Front Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly



A

B

17.CHECK REAR AIRBAG SENSOR LH

C

D

17.CHECK REAR AIRBAG SENSOR LH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the rear airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor LH (for Front Side)



A

18.CHECK SIDE AIRBAG SENSOR LH (for Rear Side)

B

C

18.CHECK SIDE AIRBAG SENSOR LH (for Rear Side)
a.
C238395E09
0.698,0.938 0.875,1.115 0.177,0.177 10 false *1 2.552,0.938 2.729,1.115 0.177,0.177 10 false *2 2.25,0.99 2.375,1.188 0.125,0.198 10 false A 2.094,0.99 2.219,1.188 0.125,0.198 10 false B 1.74,0.99 1.865,1.188 0.125,0.198 10 false C 1.583,0.99 1.708,1.188 0.125,0.198 10 false D 1.25,1 1.375,1.198 0.125,0.198 10 false E 1.094,1 1.219,1.198 0.125,0.198 10 false F

Interchange the side airbag sensor LH (for Rear Side) with RH (for Rear Side) and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1647, B1648 or 82 is output. A
DTC B1642, B1643 or 81 is output. B
DTCs B1642, B1643, B1647, B1648, 81 and 82 are not output. C


HINT:

Codes other than DTCs B1642, B1643, B1647, B1648, 81 and 82 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the side airbag sensor LH (for Rear Side) and RH (for Rear Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor LH



A

B

C

19.CHECK HISTORY DTC
a.

Check for history DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
History DTC B1637 is not output. A
History DTC B1637 is output. B


HINT:

Codes other than history DTC B1637 may be output at this time, but they are not related to this check.




A

20.CHECK CONNECTORS

B

39.CHECK REAR AIRBAG SENSOR LH
20.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the side airbag sensor LH (for Front Side) and rear airbag sensor LH.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the side airbag sensor LH (for Front Side) and rear airbag sensor LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

21.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

21.CHECK FLOOR WIRE (OPEN)
a.
U189560E01
1.173,2.317 1.294,2.470 0.121,0.153 10 D 1.483,2.317 1.604,2.470 0.121,0.153 10 C 1.836,2.317 1.957,2.470 0.121,0.153 10 B 2.15,2.317 2.270,2.470 0.121,0.153 10 A 0.754,2.317 0.923,2.468 0.169,0.150 10 *1 0.641,0.146 0.840,0.318 0.199,0.172 10 *a 0.357,3.207 0.538,3.361 0.181,0.154 10 *b 0.983,4.066 1.359,4.224 0.376,0.158 10 BCL- 1.843,4.066 2.240,4.224 0.397,0.158 10 BCL+ 0.491,3.578 0.780,3.735 0.289,0.158 10 M34 0.881,0.572 1.172,0.730 0.291,0.158 10 M33 2.154,1.071 2.526,1.228 0.372,0.158 10 BCL- 1.273,1.071 1.680,1.228 0.407,0.158 10 BCL+ 1.82,0.698 1.484,1.046 false 1.975,0.698 2.312,1.046 false 1.331,1.773 1.489,1.926 0.158,0.153 10 *3 2.448,2.317 2.624,2.486 0.176,0.169 10 *2 1.715,2.331 1.715,1.853 1.715,1.853 1.537,1.853 false 1.524,3.673 1.195,4.049 false 1.693,3.673 2.022,4.049 false 1.609,4.024 1.609,4.299 false 1.52,4.305 1.679,4.458 0.158,0.153 10 *4

Using a service wire, connect terminals 4 (BCL+) and 3 (BCL-) of connector C.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - M33-2 (BCL-) Always Below 1 Ω



c.

Disconnect the service wire from connector C.

Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))
*b Front view of wire harness connector
(to Rear Airbag Sensor LH)



OK

22.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

22.CHECK FLOOR WIRE (SHORT)
a.
U189549E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.165,2.317 1.458,2.474 0.293,0.158 10 M33 2.337,2.865 2.724,3.023 0.387,0.158 10 BCL- 1.654,2.865 2.050,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - M33-2 (BCL-) Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

23.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

23.CHECK FLOOR WIRE (SHORT TO B+)
a.
U189549E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.165,2.317 1.458,2.474 0.293,0.158 10 M33 2.337,2.865 2.724,3.023 0.387,0.158 10 BCL- 1.654,2.865 2.050,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - Body ground Engine switch on (IG) Below 1 V
M33-2 (BCL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

24.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

24.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U189549E01
1.142,0.718 1.263,0.871 0.121,0.153 10 D 1.457,0.718 1.577,0.871 0.121,0.153 10 C 1.907,0.718 2.028,0.871 0.121,0.153 10 B 2.22,0.718 2.340,0.871 0.121,0.153 10 A 0.803,0.718 0.985,0.873 0.183,0.155 10 *1 2.463,0.718 2.636,0.874 0.173,0.156 10 *2 1.372,0.116 1.545,0.268 0.172,0.152 10 *3 0.993,1.873 1.181,2.025 0.188,0.151 10 *a 1.165,2.317 1.458,2.474 0.293,0.158 10 M33 2.337,2.865 2.724,3.023 0.387,0.158 10 BCL- 1.654,2.865 2.050,3.023 0.396,0.158 10 BCL+ 2.102,2.46 1.853,2.842 false 2.227,2.46 2.476,2.842 false 1.738,0.73 1.738,0.195 1.738,0.195 1.576,0.195 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M33-1 (BCL+) - Body ground Always 1 MΩ or higher
M33-2 (BCL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Side Airbag Sensor LH (for Front Side)
*3 Floor Wire
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Front Side))



OK

25.CHECK SIDE AIRBAG SENSOR LH (for Front Side)

NG

REPLACE FLOOR WIRE

25.CHECK SIDE AIRBAG SENSOR LH (for Front Side)
a.
C238224E05
0.792,1.01 0.938,1.198 0.146,0.188 10 false *1 2.313,1.01 2.521,1.198 0.208,0.188 10 false *2 1.875,1.01 2,1.198 0.125,0.188 10 false A 1.708,1.01 1.833,1.198 0.125,0.188 10 false B 1.271,1.01 1.396,1.198 0.125,0.188 10 false C 1.115,1.01 1.24,1.198 0.125,0.188 10 false D

Connect the connector to the rear airbag sensor LH.


b.

Interchange the side airbag sensor LH (for Front Side) with RH (for Front Side) and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the side airbag sensor LH (for Front Side) and RH (for Front Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly



A

26.CHECK REAR AIRBAG SENSOR LH

B

C

26.CHECK REAR AIRBAG SENSOR LH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Interchange the rear airbag sensor LH with RH and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1638 is output. A
DTC B1633 is output. B
DTCs B1633 and B1638 are not output. C


HINT:

Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor LH (for Front Side)



A

C

C

27.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the rear airbag sensor LH and side airbag sensor LH (for Rear Side). Also check that the connectors that link the floor wire and rear door wire LH are properly connected.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the rear airbag sensor LH and side airbag sensor LH (for Rear Side). Also disconnect the connectors that link the floor wire and rear door wire LH.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

28.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (OPEN)

NG

REPLACE WIRE HARNESS

28.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (OPEN)
a.
U189774E02
1.573,3.719 1.281,4.115 false 1.719,3.719 2.01,4.115 false 1.75,0.792 1.5,0.281 false 1.927,0.802 2.177,0.292 false 1.865,1.26 1.865,1.354 1.865,1.354 2.26,1.354 false 1.563,2.292 1.688,2.448 0.125,0.156 10 false D 1.729,2.292 1.854,2.448 0.125,0.156 10 false C 2.073,2.292 2.198,2.448 0.125,0.156 10 false B 2.375,2.292 2.5,2.448 0.125,0.156 10 false A 2.688,2.292 2.875,2.469 0.188,0.177 10 false *2 0.49,2.292 0.708,2.479 0.219,0.188 10 false *1 0.344,3.146 0.552,3.354 0.208,0.208 10 false *b 0.625,0.167 0.813,0.396 0.188,0.229 10 false *a 1.021,4.135 1.396,4.292 0.375,0.156 10 false BDL- 1.844,4.135 2.25,4.292 0.406,0.156 10 false BDL+ 0.5,3.552 0.771,3.708 0.271,0.156 10 false L14 0.792,0.667 1.083,0.823 0.292,0.156 10 false M34 2.219,0.188 2.583,0.344 0.365,0.156 10 false BDL- 1.063,0.188 1.469,0.344 0.406,0.156 10 false BDL+ 0.917,2.292 1.042,2.448 0.125,0.156 10 false F 1.219,2.292 1.344,2.448 0.125,0.156 10 false E 2.281,1.26 2.438,1.438 0.156,0.177 10 false *3

Connect the connectors that link the floor wire and rear door wire LH.


b.

Using a service wire, connect terminals 1 (BDL+) and 2 (BDL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - L14-1 (BDL-) Always Below 1 Ω


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*3 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

29.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT)

NG

34.CHECK FLOOR WIRE (OPEN)
29.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT)
a.
U189761E02
1.729,2.281 1.344,2.719 false 1.896,2.292 2.292,2.729 false 1.583,0.677 1.708,0.833 0.125,0.156 10 false D 1.729,0.677 1.854,0.833 0.125,0.156 10 false C 2.073,0.677 2.198,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.635,2.177 0.927,2.333 0.292,0.156 10 false L14 2.135,2.729 2.552,2.906 0.417,0.177 10 false BDL+ 1.135,2.729 1.542,2.885 0.406,0.156 10 false BDL- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.677 1.354,0.833 0.125,0.156 10 false E

Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - L14-1 (BDL-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

30.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO B+)

NG

35.CHECK FLOOR WIRE (SHORT)
30.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO B+)
a.
U189761E02
1.729,2.281 1.344,2.719 false 1.896,2.292 2.292,2.729 false 1.583,0.677 1.708,0.833 0.125,0.156 10 false D 1.729,0.677 1.854,0.833 0.125,0.156 10 false C 2.073,0.677 2.198,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.635,2.177 0.927,2.333 0.292,0.156 10 false L14 2.135,2.729 2.552,2.906 0.417,0.177 10 false BDL+ 1.135,2.729 1.542,2.885 0.406,0.156 10 false BDL- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.677 1.354,0.833 0.125,0.156 10 false E

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - Body ground Engine switch on (IG) Below 1 V
L14-1 (BDL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

31.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO GROUND)

NG

36.CHECK FLOOR WIRE (SHORT TO B+)
31.CHECK SIDE AIRBAG SENSOR LH CIRCUIT (for Rear Side) (SHORT TO GROUND)
a.
U189761E02
1.729,2.281 1.344,2.719 false 1.896,2.292 2.292,2.729 false 1.583,0.677 1.708,0.833 0.125,0.156 10 false D 1.729,0.677 1.854,0.833 0.125,0.156 10 false C 2.073,0.677 2.198,0.833 0.125,0.156 10 false B 2.385,0.677 2.51,0.833 0.125,0.156 10 false A 2.677,0.625 2.865,0.792 0.188,0.167 10 false *2 0.51,0.625 0.698,0.792 0.188,0.167 10 false *1 0.479,1.635 0.688,1.854 0.208,0.219 10 false *a 0.635,2.177 0.927,2.333 0.292,0.156 10 false L14 2.135,2.729 2.552,2.906 0.417,0.177 10 false BDL+ 1.135,2.729 1.542,2.885 0.406,0.156 10 false BDL- 0.917,0.677 1.042,0.833 0.125,0.156 10 false F 1.229,0.677 1.354,0.833 0.125,0.156 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L14-2 (BDL+) - Body ground Always 1 MΩ or higher
L14-1 (BDL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*a Front view of wire harness connector
(to Side Airbag Sensor LH (for Rear Side))



OK

32.CHECK REAR AIRBAG SENSOR LH

NG

37.CHECK FLOOR WIRE (SHORT TO GROUND)
32.CHECK REAR AIRBAG SENSOR LH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Connect the connector to the side airbag sensor LH (for Rear Side).


b.

Interchange the rear airbag sensor LH with RH and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1684 or B1689 is output. A
DTC B1673 or B1674 is output. B
DTCs B1673, B1674, B1684 and B1689 are not output. C


HINT:

Codes other than DTCs B1673, B1674, B1684 and B1689 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor LH (for Front Side)



A

33.CHECK SIDE AIRBAG SENSOR LH (for Rear Side)

B

C

33.CHECK SIDE AIRBAG SENSOR LH (for Rear Side)
a.
C238395E09
0.698,0.938 0.875,1.115 0.177,0.177 10 false *1 2.552,0.938 2.729,1.115 0.177,0.177 10 false *2 2.25,0.99 2.375,1.188 0.125,0.198 10 false A 2.094,0.99 2.219,1.188 0.125,0.198 10 false B 1.74,0.99 1.865,1.188 0.125,0.198 10 false C 1.583,0.99 1.708,1.188 0.125,0.198 10 false D 1.25,1 1.375,1.198 0.125,0.198 10 false E 1.094,1 1.219,1.198 0.125,0.198 10 false F

Interchange the side airbag sensor LH (for Rear Side) with RH (for Rear Side) and connect the connectors.


b.

Connect the cable to the negative (-) battery terminal.



d.

Turn the engine switch off.


e.

Turn the engine switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1684 or B1689 is output. A
DTC B1673 or B1674 is output. B
DTCs B1673, B1674, B1684 and B1689 are not output. C


HINT:

Codes other than DTCs B1673, B1674, B1684 and B1689 may be output at this time, but they are not related to this check.



g.

Turn the engine switch off.


h.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



i.

Return the side airbag sensor LH (for Rear Side) and RH (for Rear Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor RH (for Rear Side)
*2 Rear Airbag Sensor LH



A

B

C

34.CHECK FLOOR WIRE (OPEN)
a.
U189603E02
1.688,3.635 1.365,3.313 true 1.875,3.656 2.198,3.333 true 2.063,0.844 1.771,0.333 true 2.167,0.865 2.479,0.333 true 2.115,1.229 2.115,1.365 2.115,1.365 2.427,1.365 false 1.323,2.375 1.323,2.604 false 2.135,2.24 2.135,1.885 2.135,1.885 1.917,1.885 false 2.24,3.229 2.646,3.396 0.406,0.167 10 false BDL+ 0.979,3.219 1.333,3.385 0.354,0.167 10 false BDL- 2.51,0.25 2.896,0.417 0.385,0.167 10 false BDL- 1.292,0.25 1.688,0.417 0.396,0.167 10 false BDL+ 0.802,3.729 1.104,3.885 0.302,0.156 10 false LM3 1.188,0.771 1.479,0.927 0.292,0.156 10 false M34 1.01,0.229 1.167,0.396 0.156,0.167 10 false *a 0.625,3.021 0.802,3.188 0.177,0.167 10 false *b 2.458,1.25 2.635,1.417 0.177,0.167 10 false *5 0.365,2.229 0.531,2.396 0.167,0.167 10 false *1 0.688,2.229 0.792,2.396 0.104,0.167 10 false F 1.052,2.229 1.167,2.396 0.115,0.167 10 false E 1.49,2.229 1.604,2.396 0.115,0.167 10 false D 1.854,2.24 1.969,2.406 0.115,0.167 10 false C 2.313,2.229 2.427,2.396 0.115,0.167 10 false B 2.677,2.229 2.792,2.396 0.115,0.167 10 false A 2.927,2.208 3.094,2.375 0.167,0.167 10 false *2 1.229,2.615 1.406,2.781 0.177,0.167 10 false *3 1.719,1.781 1.875,1.948 0.156,0.167 10 false *4

Disconnect the rear door wire LH connector from the floor wire.

HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LM3-1 (BDL+) - LM3-2 (BDL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*3 Rear Door Wire LH
*4 Floor Wire
*5 Service Wire
*a Front view of wire harness connector
(to Rear Airbag Sensor LH)
*b Front view of wire harness connector
(to Rear Door Wire LH)



OK

REPLACE REAR DOOR WIRE LH

NG

REPLACE FLOOR WIRE

35.CHECK FLOOR WIRE (SHORT)
a.
U189601E02
1.51,2.365 1.26,2.052 false 1.729,2.375 1.979,2.063 false 1.333,0.938 1.333,1.167 false 2.073,0.802 2.073,0.458 2.073,0.458 1.854,0.458 false 2.021,1.927 2.427,2.094 0.406,0.167 10 false BDL+ 0.844,1.927 1.198,2.094 0.354,0.167 10 false BDL- 0.667,2.427 0.969,2.583 0.302,0.156 10 false LM3 0.49,1.802 0.667,1.969 0.177,0.167 10 false *a 0.406,0.719 0.573,0.885 0.167,0.167 10 false *1 0.792,0.781 0.896,0.948 0.104,0.167 10 false F 1.094,0.781 1.208,0.948 0.115,0.167 10 false E 1.5,0.781 1.615,0.948 0.115,0.167 10 false D 1.813,0.771 1.927,0.938 0.115,0.167 10 false C 2.219,0.781 2.333,0.948 0.115,0.167 10 false B 2.531,0.781 2.646,0.948 0.115,0.167 10 false A 2.813,0.719 2.979,0.885 0.167,0.167 10 false *2 1.25,1.198 1.427,1.365 0.177,0.167 10 false *3 1.667,0.365 1.823,0.531 0.156,0.167 10 false *4

Disconnect the rear door wire LH connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LM3-1 (BDL+) - LM3-2 (BDL-) Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*3 Rear Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Rear Door Wire LH)



OK

REPLACE REAR DOOR WIRE LH

NG

REPLACE FLOOR WIRE

36.CHECK FLOOR WIRE (SHORT TO B+)
a.
U189601E02
1.51,2.365 1.26,2.052 false 1.729,2.375 1.979,2.063 false 1.333,0.938 1.333,1.167 false 2.073,0.802 2.073,0.458 2.073,0.458 1.854,0.458 false 2.021,1.927 2.427,2.094 0.406,0.167 10 false BDL+ 0.844,1.927 1.198,2.094 0.354,0.167 10 false BDL- 0.667,2.427 0.969,2.583 0.302,0.156 10 false LM3 0.49,1.802 0.667,1.969 0.177,0.167 10 false *a 0.406,0.719 0.573,0.885 0.167,0.167 10 false *1 0.792,0.781 0.896,0.948 0.104,0.167 10 false F 1.094,0.781 1.208,0.948 0.115,0.167 10 false E 1.5,0.781 1.615,0.948 0.115,0.167 10 false D 1.813,0.771 1.927,0.938 0.115,0.167 10 false C 2.219,0.781 2.333,0.948 0.115,0.167 10 false B 2.531,0.781 2.646,0.948 0.115,0.167 10 false A 2.813,0.719 2.979,0.885 0.167,0.167 10 false *2 1.25,1.198 1.427,1.365 0.177,0.167 10 false *3 1.667,0.365 1.823,0.531 0.156,0.167 10 false *4

Disconnect the rear door wire LH connector from the floor wire.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
LM3-1 (BDL+) - Body ground Engine switch on (IG) Below 1 V
LM3-2 (BDL-) - Body ground Engine switch on (IG) Below 1 V


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*3 Rear Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Rear Door Wire LH)



OK

REPLACE REAR DOOR WIRE LH

NG

REPLACE FLOOR WIRE

37.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U189601E02
1.51,2.365 1.26,2.052 false 1.729,2.375 1.979,2.063 false 1.333,0.938 1.333,1.167 false 2.073,0.802 2.073,0.458 2.073,0.458 1.854,0.458 false 2.021,1.927 2.427,2.094 0.406,0.167 10 false BDL+ 0.844,1.927 1.198,2.094 0.354,0.167 10 false BDL- 0.667,2.427 0.969,2.583 0.302,0.156 10 false LM3 0.49,1.802 0.667,1.969 0.177,0.167 10 false *a 0.406,0.719 0.573,0.885 0.167,0.167 10 false *1 0.792,0.781 0.896,0.948 0.104,0.167 10 false F 1.094,0.781 1.208,0.948 0.115,0.167 10 false E 1.5,0.781 1.615,0.948 0.115,0.167 10 false D 1.813,0.771 1.927,0.938 0.115,0.167 10 false C 2.219,0.781 2.333,0.948 0.115,0.167 10 false B 2.531,0.781 2.646,0.948 0.115,0.167 10 false A 2.813,0.719 2.979,0.885 0.167,0.167 10 false *2 1.25,1.198 1.427,1.365 0.177,0.167 10 false *3 1.667,0.365 1.823,0.531 0.156,0.167 10 false *4

Disconnect the rear door wire LH connector from the floor wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
LM3-1 (BDL+) - Body ground Always 1 MΩ or higher
LM3-2 (BDL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Side Airbag Sensor LH (for Rear Side)
*2 Rear Airbag Sensor LH
*3 Rear Door Wire LH
*4 Floor Wire
*a Front view of wire harness connector
(to Rear Door Wire LH)



OK

REPLACE REAR DOOR WIRE LH

NG

REPLACE FLOOR WIRE

38.CHECK SIDE AIRBAG SENSOR LH (for Front Side)
a.
C238224E05
0.792,1.01 0.938,1.198 0.146,0.188 10 false *1 2.313,1.01 2.521,1.198 0.208,0.188 10 false *2 1.875,1.01 2,1.198 0.125,0.188 10 false A 1.708,1.01 1.833,1.198 0.125,0.188 10 false B 1.271,1.01 1.396,1.198 0.125,0.188 10 false C 1.115,1.01 1.24,1.198 0.125,0.188 10 false D

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the side airbag sensor LH (for Front Side) with RH (for Front Side) and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1627 is output. A
DTC B1622 is output. B
DTCs B1622 and B1627 are not output. C


HINT:

Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the side airbag sensor LH (for Front Side) and RH (for Front Side) to their original positions and connect the connectors.

Text in Illustration
*1 Side Airbag Sensor RH (for Front Side)
*2 Center Airbag Sensor Assembly



A

B

C

39.CHECK REAR AIRBAG SENSOR LH
a.
C238223E04
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Interchange the rear airbag sensor LH with RH and connect the connectors.


d.

Connect the cable to the negative (-) battery terminal.



f.

Turn the engine switch off.


g.

Turn the engine switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1637 is output. A
DTC B1632 is output. B
DTCs B1632 and B1637 are not output. C


HINT:

Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.



i.

Turn the engine switch off.


j.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Rear Airbag Sensor RH
*2 Side Airbag Sensor LH (for Front Side)



A

B

C