Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291898 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1678/86  Lost Communication with Rear Floor Airbag Sensor  B1679/86  Rear Floor Airbag Sensor Initialization Incomplete  


DESCRIPTION

The side collision sensor LH circuit (bus 2) consists of the center airbag sensor assembly and rear floor airbag sensor.

The rear floor airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor assembly to determine if the airbags should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor LH circuit (bus 2).

DTC No. DTC Detection Condition Trouble Area
B1678/86
B1679/86
·

The center airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor LH circuit (bus 2).

·

Rear floor airbag sensor malfunction

·

Center airbag sensor assembly malfunction


·

Floor wire

·

Rear floor airbag sensor

·

Center airbag sensor assembly



WIRING DIAGRAM

C303969E27
5.302,2.885 6.865,3.5 1.563,0.615 10 false Center Airbag Sensor Assembly 5.302,2.719 6.865,3.333 1.563,0.615 10 false M9 5.135,0.802 5.438,1.208 0.302,0.406 10 false 11 5.135,1.771 5.854,2.167 0.719,0.396 10 false 12 5.375,0.906 6.094,1.302 0.719,0.396 10 false BCL+ 5.375,1.875 6.094,2.271 0.719,0.396 10 false BCL- 1.396,0.906 2.115,1.302 0.719,0.396 10 false BEL+ 1.417,1.875 2.135,2.271 0.719,0.396 10 false BEL- 1.844,0.802 2.563,1.198 0.719,0.396 10 false 2 1.844,1.781 2.563,2.177 0.719,0.396 10 false 1 0.563,2.719 2.125,3.333 1.563,0.615 10 false M21 0.563,2.885 2.802,3.156 2.24,0.271 10 false Rear Floor Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK CONNECTORS
a.

Turn the engine switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the center airbag sensor assembly and rear floor airbag sensor.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the center airbag sensor assembly and rear floor airbag sensor.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.




OK

2.CHECK FLOOR WIRE (OPEN)

NG

REPLACE FLOOR WIRE

2.CHECK FLOOR WIRE (OPEN)
a.
U189772E02
1.833,0.948 1.531,1.281 true 1.958,0.969 2.26,1.302 true 1.375,3.667 0.99,4.073 false 1.625,3.688 1.99,4.104 false 1.896,1.333 1.896,1.521 false 1.573,2.292 1.573,1.844 1.573,1.844 1.417,1.844 false 0.844,2.292 0.969,2.448 0.125,0.156 10 false D 1.188,2.292 1.313,2.448 0.125,0.156 10 false C 1.792,2.292 1.917,2.448 0.125,0.156 10 false B 2.146,2.302 2.271,2.458 0.125,0.156 10 false A 0.531,2.292 0.719,2.469 0.188,0.177 10 false *1 2.604,2.281 2.76,2.438 0.156,0.156 10 false *2 0.625,0.208 0.823,0.375 0.198,0.167 10 false *a 0.396,3.188 0.563,3.344 0.167,0.156 10 false *b 1.104,0.604 1.385,0.76 0.281,0.156 10 false M9 1.156,1.24 1.552,1.396 0.396,0.156 10 false BCL+ 2.333,1.25 2.833,1.521 0.5,0.271 10 false BCL- 0.594,3.625 0.885,3.771 0.292,0.146 10 false M21 0.76,4.083 1.135,4.292 0.375,0.208 10 false BEL- 1.875,4.104 2.354,4.313 0.479,0.208 10 false BEL+ 1.833,1.531 1.99,1.688 0.156,0.156 10 false *4 1.208,1.802 1.365,1.958 0.156,0.156 10 false *3

Using a service wire, connect terminals 11 (BCL+) and 12 (BCL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M21-2 (BEL+) - M21-1 (BEL-) Always Below 1 Ω



c.

Disconnect the service wire from connector B.

Text in Illustration
*1 Rear Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*4 Service Wire
*a Front view of wire harness connector
(to Center Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Rear Floor Airbag Sensor)



OK

3.CHECK FLOOR WIRE (SHORT)

NG

REPLACE FLOOR WIRE

3.CHECK FLOOR WIRE (SHORT)
a.
U189768E02
1.521,2.333 1.313,2.74 false 1.792,2.344 1.99,2.76 false 1.604,0.625 1.604,0.177 1.604,0.177 1.396,0.177 false 0.833,0.594 0.958,0.75 0.125,0.156 10 false D 1.208,0.594 1.333,0.75 0.125,0.156 10 false C 1.833,0.594 1.958,0.75 0.125,0.156 10 false B 2.208,0.594 2.333,0.75 0.125,0.156 10 false A 0.51,0.521 0.698,0.698 0.188,0.177 10 false *1 2.604,0.521 2.76,0.677 0.156,0.156 10 false *2 0.583,1.698 0.792,1.896 0.208,0.198 10 false *a 0.74,2.24 1.031,2.385 0.292,0.146 10 false M21 1.094,2.76 1.469,2.969 0.375,0.208 10 false BEL- 1.875,2.792 2.354,3 0.479,0.208 10 false BEL+ 1.198,0.083 1.385,0.26 0.188,0.177 10 false *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M21-2 (BEL+) - M21-1 (BEL-) Always 1 MΩ or higher


Text in Illustration
*1 Rear Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Rear Floor Airbag Sensor)



OK

4.CHECK FLOOR WIRE (SHORT TO B+)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (SHORT TO B+)
a.
U189768E02
1.521,2.333 1.313,2.74 false 1.792,2.344 1.99,2.76 false 1.604,0.625 1.604,0.177 1.604,0.177 1.396,0.177 false 0.833,0.594 0.958,0.75 0.125,0.156 10 false D 1.208,0.594 1.333,0.75 0.125,0.156 10 false C 1.833,0.594 1.958,0.75 0.125,0.156 10 false B 2.208,0.594 2.333,0.75 0.125,0.156 10 false A 0.51,0.521 0.698,0.698 0.188,0.177 10 false *1 2.604,0.521 2.76,0.677 0.156,0.156 10 false *2 0.583,1.698 0.792,1.896 0.208,0.198 10 false *a 0.74,2.24 1.031,2.385 0.292,0.146 10 false M21 1.094,2.76 1.469,2.969 0.375,0.208 10 false BEL- 1.875,2.792 2.354,3 0.479,0.208 10 false BEL+ 1.198,0.083 1.385,0.26 0.188,0.177 10 false *3

Connect the cable to the negative (-) battery terminal.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M21-2 (BEL+) - Body ground Engine switch on (IG) Below 1 V
M21-1 (BEL-) - Body ground Engine switch on (IG) Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


Text in Illustration
*1 Rear Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Rear Floor Airbag Sensor)



OK

5.CHECK FLOOR WIRE (SHORT TO GROUND)

NG

REPLACE FLOOR WIRE

5.CHECK FLOOR WIRE (SHORT TO GROUND)
a.
U189768E02
1.521,2.333 1.313,2.74 false 1.792,2.344 1.99,2.76 false 1.604,0.625 1.604,0.177 1.604,0.177 1.396,0.177 false 0.833,0.594 0.958,0.75 0.125,0.156 10 false D 1.208,0.594 1.333,0.75 0.125,0.156 10 false C 1.833,0.594 1.958,0.75 0.125,0.156 10 false B 2.208,0.594 2.333,0.75 0.125,0.156 10 false A 0.51,0.521 0.698,0.698 0.188,0.177 10 false *1 2.604,0.521 2.76,0.677 0.156,0.156 10 false *2 0.583,1.698 0.792,1.896 0.208,0.198 10 false *a 0.74,2.24 1.031,2.385 0.292,0.146 10 false M21 1.094,2.76 1.469,2.969 0.375,0.208 10 false BEL- 1.875,2.792 2.354,3 0.479,0.208 10 false BEL+ 1.198,0.083 1.385,0.26 0.188,0.177 10 false *3

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M21-2 (BEL+) - Body ground Always 1 MΩ or higher
M21-1 (BEL-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Rear Floor Airbag Sensor
*2 Center Airbag Sensor Assembly
*3 Floor Wire
*a Front view of wire harness connector
(to Rear Floor Airbag Sensor)



OK

6.CHECK REAR FLOOR AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

6.CHECK REAR FLOOR AIRBAG SENSOR
a.
C238224E05
0.792,1.01 0.938,1.198 0.146,0.188 10 false *1 2.313,1.01 2.521,1.198 0.208,0.188 10 false *2 1.875,1.01 2,1.198 0.125,0.188 10 false A 1.708,1.01 1.833,1.198 0.125,0.188 10 false B 1.271,1.01 1.396,1.198 0.125,0.188 10 false C 1.115,1.01 1.24,1.198 0.125,0.188 10 false D

Connect the connector to the center airbag sensor assembly.


b.

Interchange the rear floor airbag sensor with center floor airbag sensor and connect the connectors.


c.

Connect the cable to the negative (-) battery terminal.



e.

Turn the engine switch off.


f.

Turn the engine switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTCs B1666/85, B1667/85, B1678/86 and B1679/86 are not output. A
DTC B1678/86 or B1679/86 is output. B
DTC B1666/85 or B1667/85 is output. C


HINT:

Codes other than DTCs B1666/85, B1667/85, B1678/86 and B1679/86 may be output at this time, but they are not related to this check.



h.

Turn the engine switch off.


i.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



j.

Return the rear floor airbag sensor and center floor airbag sensor to their original positions and connect the connectors.

Text in Illustration
*1 Center Floor Airbag Sensor
*2 Center Airbag Sensor Assembly



A

B

C