Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD(for LHD) › from 2016.05
RM24M0E _58 Vehicle Interior _059562 SUPPLEMENTAL RESTRAINT SYSTEMS _0291913 STEERING PAD(for LHD) N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD(for LHD)  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS component, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this procedure.


·

Never dispose of a steering pad with an unactivated airbag.


·

The airbag produces a loud, exploding sound when it activates. Perform the operation where it will not be a nuisance to people nearby.


·
C110371E62
0.958,1.219 0.74,0.771 false 0.573,0.583 0.885,0.781 0.313,0.198 10 false SST

When activating the airbag, always use the specified SST (SRS airbag deployment tool).


·

Perform procedures in a place away from electrical interference.


·

When activating the airbag, stand at least 10 m (33 ft.) away from the steering pad.


·

The steering pad becomes very hot when the airbag is deployed. Do not touch it for at least 30 minutes after activation.


·

Use gloves and safety glasses when handling a steering pad with a deployed airbag.


·

Do not apply water to a steering pad with a deployed airbag.


·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPARTMENT of the DISTRIBUTOR.


Hide 45130 2.DISPOSE OF STEERING PAD ASSEMBLY TOGETHER WITH VEHICLE

HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371E62
0.958,1.219 0.74,0.771 false 0.573,0.583 0.885,0.781 0.313,0.198 10 false SST

Check if SST is functioning properly.

SST
09082-00700  

i.
C110372E32
0.917,1.615 0.781,1.219 false 0.615,1.052 1.052,1.25 0.438,0.198 10 false SST 2.594,0.656 3.146,0.854 0.552,0.198 10 false Battery

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.

HINT:

The yellow connector will be used to connect to another SST in a later step.



ii.
C110475E28
1.76,0.625 1.458,0.313 false 1.188,0.167 1.542,0.365 0.354,0.198 10 false SST

Press the SST activation switch, and check that the LED of the SST activation switch illuminates.

CAUTION:

If the LED illuminates when the activation switch is not pressed, SST may have a malfunction, in which case that SST should not be used.



iii.

Disconnect SST from the battery.




c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



d.

Remove the steering column cover (see page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY(for LHD)>REMOVAL).


e.

Install SST.

CAUTION:

Check that there is no free play in the steering wheel and steering pad.


i.

Disconnect the yellow airbag connector from the spiral cable.

NOTICE:

When handling the airbag connector, do not damage the airbag wire harness.



ii.
C141983E02
1.115,1.927 1.323,2.094 0.208,0.167 10 false (A) 1.604,1.292 1.813,1.458 0.208,0.167 10 true (B)

Connect SST (A) to SST (B). Then connect SST (B)'s connector to the spiral cable.

SST
09082-00700  
09082-00780  

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.



iii.
U186046E02
1.01,1.875 2.49,1.875 false 2.625,1.063 2.625,1.938 false 0.865,1.823 0.865,1.948 false 0.469,1.219 0.688,1.521 false 1.792,0.479 2.271,0.688 0.479,0.208 10 false Battery 0.146,1.125 0.5,1.333 0.354,0.208 10 false SST 1.219,1.438 2.146,1.646 0.927,0.208 10 false 10 m or more

Move SST at least 10 m (33 ft.) away from the front side window.


iv.

Maintaining enough clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not do damage the SST wire harness.



v.

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.



f.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.


ii.

Press the SST activation switch and deploy the airbag.

CAUTION:
·

When deploying the airbag, make sure that no one is near the vehicle.


·

The steering pad becomes extremely hot when the airbag is deployed. Do not touch it for at least 30 minutes after deployment.


·

Use gloves and safety glasses when handling a steering pad with a deployed airbag.


·

Do not apply water to a steering pad with a deployed airbag.


·

Always wash your hands with water after completing the operation.



HINT:

The airbag is deployed as the SST activation switch LED illuminates.




Hide 45130 3.DISPOSE OF ONLY STEERING PAD ASSEMBLY

NOTICE:
·

When disposing of the steering pad, never use the customer's vehicle to deploy the airbag.


·

Be sure to follow the procedure detailed below when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
B104819E02
0.142,0.659 0.472,0.861 0.330,0.202 10 SST 0.574,0.758 1.004,1.222 false

Check if SST is functioning properly (see previous step).


b.

Remove the steering pad (see page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD(for LHD)>REMOVAL).

CAUTION:
·

When removing the steering pad, work must be started 90 seconds after the ignition switch is turned off and after the cable is disconnected from the negative (-) battery terminal.


·

When storing the steering pad, keep the airbag deployment side facing upward.




c.
B104882E04
1.857,1.189 1.857,1.567 false 1.245,0.261 2.741,0.465 1.496,0.204 10 Wire Harness Diameter 0.652,1.586 2.620,1.788 1.968,0.202 10 Stripped Wire Harness Section

Using service wire harnesses for the vehicle, tie down the steering pad to a disc wheel (with tire).

Wire harness:

Stripped wire harness section

1.25 mm2 or more (0.0019 in.2 or more)


NOTICE:

Use a disc wheel (with tire) that you are planning to throw away, as the airbag deployment will damage the disc wheel.


CAUTION:

Do not use wire harnesses that are too thin or any other substitute items to tie down the steering pad. They may snap when the airbag deploys. Always use vehicle wire harnesses that have an area of at least 1.25 mm2 or more (0.0019 in.2).


HINT:

To calculate the area of the stripped wire harness section:

Area = 3.14 x Diameter2/4




i.
C136814E02
2.302,1.462 2.439,1.605 0.137,0.142 10 M 2.81,1.173 2.947,1.316 0.137,0.142 10 L

Install the 2 bolts with washers into the 2 bolt holes of the steering pad.

Bolt:
L:

35.0 mm (1.378 in.)

M:

6.0 mm (0.236 in.)

Pitch:

1.0 mm (0.039 in.)


NOTICE:
·

Tighten the bolts by hand until they become difficult to turn.


·

Do not tighten the bolts excessively.




ii.
C136815E02
2.188,1.198 2.188,0.729 false 2.188,0.729 2.729,0.729 false 2.594,1.302 2.594,0.729 false 2.781,0.656 3.083,0.802 0.302,0.146 10 false SST

After connecting SST to each other, connect them to the steering pad.

SST
09082-00802  (09082-10801, 09082-40800)


iii.
C136816E02
0.896,3.146 0.896,1.573 true 0.896,1.573 1.74,1.573 true 2.552,3.146 2.552,2.125 true 1.135,2.125 0.906,2.125 false 2.281,2.115 2.563,2.115 false 1.24,2.031 2.24,2.198 1,0.167 10 false 2 times or more

Wind 3 wire harnesses at least twice around the bolts installed on the left and right sides of the steering pad.

CAUTION:
·

Tightly wind the wire harnesses around the bolts so that there is no slack.


·

Make sure that the wire harnesses are tight. If there is slack in a wire harness, the steering pad may come loose when the airbag is deployed.




iv.
H044985

Face the airbag deployment side of the steering pad upward. Separately tie the left and right sides of the steering pad to a disc wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole in the disc wheel.

CAUTION:
·

Make sure that the wire harnesses are tight. If there is slack in a wire harness, the steering pad may come loose when the airbag is deployed.


·

Always tie down the steering pad with the airbag deployment side facing upward.





d.
H044986E05
2.531,0.448 2.531,1.354 false 2.375,0.25 2.667,0.396 0.292,0.146 10 false SST

Install SST.

SST
09082-00700  

CAUTION:

Place the tire with disc wheel and steering pad on a level surface.


i.

Connect the connector of SST.

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the disc wheel.



ii.
H005075E02
0.156,1.146 0.479,1.354 0.323,0.208 10 false SST 1.75,0.125 2.24,0.323 0.49,0.198 10 false Battery 1.208,1.635 2.396,1.896 1.188,0.26 10 false 10 m or more

Move SST at least 10 m (33 ft.) away from the steering pad.



e.
H042015E09
1.031,1.688 0.781,1.875 0.781,1.875 2.198,1.719 false 2.865,0.896 2.99,1.094 0.125,0.198 10 false X 1.208,0.083 1.344,0.281 0.135,0.198 10 false Y 1.042,0.719 1.177,0.917 0.135,0.198 10 false Y 0.198,1.76 0.74,1.969 0.542,0.208 10 false Weight

Cover the steering pad with a cardboard box or tires.

i.

Covering method using a cardboard box:

Cover the steering pad with the cardboard box and place weights of at least 19 kg (43 lb) on the cardboard box in 4 places.

Cardboard box size:

X minimum = 460 mm (18.11 in.)

Y minimum = 650 mm (25.59 in.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the tire dimension, X should be the following size.

X minimum = 460 mm (18.11 in.) + width of tire



·

If using a cardboard box which is smaller than the specified size, the cardboard box will break during airbag deployment.





ii.
H043247E06
1.281,0.052 2.344,0.25 1.063,0.198 10 false Inner Diameter 2.531,0.458 2.917,0.656 0.385,0.198 10 false Width 0.094,0.833 0.531,1.021 0.438,0.188 10 false Tires 0.083,0.99 0.771,1.156 0.688,0.167 10 false (3 or more)

Covering method using tires:

Place at least 3 tires (without disc wheels) on top of the tire (with disc wheel and steering pad).

Tire size:
Width minimum:

185 mm (7.28 in.)

Inner diameter minimum:

360 mm (14.17 in.)



CAUTION:

Do not use tires with disc wheels to cover the tire (with disc wheel and steering pad).


NOTICE:
·

Use tires that you are planning to throw away, as the airbag deployment may damage the tires.


·

Do not place the SST connector under the tire as the connector may be damaged.




iii.
H043722

Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. If there is slack in a wire harness, the tires may come loose when the airbag is deployed.




f.
B110263E06
0.448,2.135 0.365,1.969 false 2.083,0.656 2.625,1.646 false 0.094,1.771 0.5,1.979 0.406,0.208 10 false SST 1.208,0.438 2.26,0.646 1.052,0.208 10 false Steering Pad 1.271,1.229 1.927,1.438 0.656,0.208 10 false Battery 1.073,2.563 2.167,2.771 1.094,0.208 10 false 10 m or more

Deploy the airbag.

i.

Connect the SST's red clip to the positive (+) battery terminal and the black clip to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (33 ft.) radius of the steering pad.


iii.

Press the SST activation switch and deploy the airbag.

CAUTION:

When deploying the airbag, make sure that no one is near the tires.


HINT:

The airbag is deployed as the SST activation switch LED illuminates.




g.
H042635

Dispose of the steering pad.

CAUTION:
·

The steering pad becomes extremely hot when the airbag is deployed. Do not touch it for at least 30 minutes after deployment.


·

Do not apply water to a steering pad with a deployed airbag.


·

Always wash your hands with water after completing the operation.



i.

Remove the steering pad from the disc wheel.


ii.

Place the steering pad in a plastic bag, tie it tightly and dispose of it in the same way as other general parts.