Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for LHD) › from 2016.05
RM24M0E _55 Steering _059560 STEERING COLUMN _0291892 STEERING COLUMN ASSEMBLY(for LHD) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for LHD)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing the steering column assembly (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45100 3.REMOVE STEERING WHEEL ASSEMBLY

a.

Disconnect each connector from the spiral cable.


b.
C138764E03
0.896,0.854 1.063,0.854 1.063,0.854 1.063,1.156 true 0.906,0.917 1.063,0.917 true 0.698,1.156 1.5,1.5 0.802,0.344 10 true Matchmark

Remove the nut and place matchmarks on the steering wheel assembly and steering column assembly.


c.
C138765E02
1.365,1.573 0.615,0.354 true 0.469,0.167 0.802,0.333 0.333,0.167 10 false SST

Using SST, remove the steering wheel assembly.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)

NOTICE:

Apply a small amount of grease to the threads and tip of SST (center bolt) before use.



Hide 45286 4.REMOVE STEERING COLUMN COVER

NOTICE:

Removing the steering column cover in the incorrect order will cause the steering column cover to break.


a.

Release the tilt lever.


b.
C158984

Push the right and left sides of the steering column cover (lower side), and disengage the 2 claws.


c.
C158985

Insert fingers into the opening of the tilt lever of the steering column cover (lower side) to disengage the claw.

HINT:

Spread the claw to disengage it.



d.
C202465E02
2.635,0.969 2.375,0.969 false 3.031,3.531 3.031,3.802 3.031,3.802 1.177,3.802 true 2.177,3.521 2.177,3.792 true 2.656,0.885 3.313,1.563 0.656,0.677 10 true Protective Tape 0.396,3.729 1.208,3.875 0.813,0.146 10 false Service Hole

Using a screwdriver, insert the tip into each service hole to disengage the 2 claws and remove the steering column cover (lower side).

HINT:

Tape the screwdriver tip before use.



e.
C356293

Disengage the 3 claws, 4 clips, and 2 pins, and remove the steering column cover (upper side).


Hide 5.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE

a.

Disconnect each connector from the turn signal switch assembly with spiral cable.


b.
C356292E02
0.677,0.635 0.677,0.26 0.677,0.26 1.604,0.26 true 0.542,0.677 0.292,0.677 0.292,0.677 0.292,1.479 true 0.219,1.469 0.385,1.646 0.167,0.177 10 false *a 1.635,0.177 1.854,0.344 0.219,0.167 10 false *b

Using pliers, expand the clamp.

Text in Illustration
*a Clamp
*b Claw


c.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable from the steering column assembly.


Hide 55302A 6.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 67914B 8.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112 9.REMOVE COWL SIDE TRIM BOARD LH

Hide 55606 10.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55432B 11.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/o Driver Side Knee Airbag)

Hide 55432B 12.REMOVE INSTRUMENT PANEL FINISH PANEL LOWER (w/ Driver Side Knee Airbag)

Hide 45259A 13.REMOVE COLUMN HOLE COVER SILENCER SHEET

a.
C128486

Turn back the floor carpet.


b.

Remove the 2 clips and column hole cover silencer sheet.


Hide 45260 14.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C356285E01
3.147,1.223 3.343,1.399 0.196,0.176 10 *a 1.71,1.312 3.114,1.312 false 1.756,1.411 2.696,1.411 2.696,1.411 2.696,1.312 false

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering intermediate shaft assembly.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

Separate the No. 2 steering intermediate shaft assembly from the steering intermediate shaft assembly.


Hide 15.REMOVE STEERING COLUMN ASSEMBLY

a.
C356290

Disconnect the 2 connectors from the power steering ECU assembly.


b.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


c.
C138769

Remove the bolt, 2 nuts and steering column assembly.

NOTICE:

Do not drop or strike the steering column assembly. If dropped or struck, replace it with a new one.



Hide 45260 16.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C356286E01
0.417,1.682 0.591,1.835 0.173,0.152 10 *a 2.059,1.059 2.059,1.781 2.059,1.781 0.641,1.781 false 1.96,1.128 1.96,1.781 false

Put matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.

Text in Illustration
*a Matchmark


b.

Remove the bolt.


c.

Remove the No. 2 steering intermediate shaft assembly from the steering column assembly.