Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(except LED Headlight) › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291933 LIGHTING SYSTEM(except LED Headlight) D

LIGHTING  LIGHTING SYSTEM(except LED Headlight)  INITIALIZATION  


NOTICE:
·

Initialize the AFS ECU (set the zero point of the height control sensor in the AFS ECU) after the vehicle height changes due to replacement of the suspension or after performing such operations as removal and reinstallation or replacement of the rear height control sensor sub-assembly LH.

·

When the AFS ECU is replaced, the initialization is also necessary.

·

Adjust the headlight aim after initializing the AFS ECU (See page Vehicle Interior>LIGHTING>HEADLIGHT ASSEMBLY(except LED Headlight)>ADJUSTMENT).


·

When a malfunction is detected in the automatic headlight beam level control system, the height control sensor signal initialization is impossible. Perform troubleshooting before initialization.



1.PREPARE VEHICLE FOR INITIALIZATION


a.

Unload the trunk and vehicle, ensuring that the spare tire, tools and jack are in their original positions.


b.

Check that there are no occupants in the vehicle.


c.

Turn off the headlights.


d.

Stop the vehicle on a level surface and keep the vehicle height unchanged.

Result:
Proceed to
NEXT




2.CHECK INDICATOR LIGHT


a.

Turn the engine switch on (IG), and check the AFS OFF indicator light.

OK:
Condition Specified Condition
The AFS ECU is replaced with a new one. Indicator light continuously blinks 6 times at 2 Hz.
Removal and reinstallation of the AFS ECU, replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. is performed. Indicator light comes on for approximately 3 seconds, and then goes off (bulb check function).


HINT:

If the indicator light does not come on when turning the engine switch on (IG), inspect and repair it according to Problem Symptoms Table (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(except LED Headlight)>PROBLEM SYMPTOMS TABLE).


Result:
Result Proceed to
OK GO TO STEP 3
NG GO TO PROBLEM SYMPTOMS TABLE




3.INITIALIZATION


a.
E106867E12
1.425,0.119 1.685,0.294 0.260,0.175 10 CG 0.137,0.021 0.579,0.224 0.442,0.202 10 DLC3: 2.896,0.62 3.162,0.790 0.266,0.170 10 LVL 2.269,0.715 2.83,0.715 false 1.558,0.726 1.558,0.309 false

Connect terminals 4 (CG) and 8 (LVL) of the DLC3 using SST.


b.
SST
09843-18040  


c.
E173059E01
0.376,1.786 0.511,1.944 0.135,0.158 10 A 0.758,1.208 0.893,1.367 0.135,0.158 10 B 1.365,0.865 1.501,1.023 0.135,0.158 10 C 2.019,0.819 2.154,0.977 0.135,0.158 10 D 2.637,1.014 2.772,1.172 0.135,0.158 10 E

Turn the low beam headlights on and off using the light control switch within 20 seconds after connecting the terminals.

HINT:

The number of times the low beam headlights need to be turned on and off is determined by the present fuel level as shown below.

Fuel Level Number of Times to Turn Low Beam Headlights on and off
Fuel level is within A range. 1
Fuel level is within B range. 2
Fuel level is within C range. 3
Fuel level is within D range. 4
Fuel level is within E range. 5


NOTICE:
·

Turn the low beam headlights on and off with certainty.

·

Turn the low beam headlights on and off at less than 3-second intervals.

·

Be sure to operate the light control switch from outside the vehicle.

·

Be sure to finish the light control switch operation within 20 seconds after connecting the DLC3 terminals.




d.

Check for the indicator light.

OK:
Condition Specified Condition
The AFS ECU is replaced with a new one. Blinks 6 times at 2 Hz → Continuously Blinks N*1 times at 2 Hz.
Removal and reinstallation of the AFS ECU, replacement of the rear height control sensor sub-assembly LH, removal and reinstallation of the rear height control sensor sub-assembly LH, replacement of the suspension, etc. is performed. Off → Continuously Blinks N*1 times at 2 Hz.


HINT:
·

*1: The number of times that AFS OFF indicator blinks is determined by the number of times the low beam headlights are turned on and off.

·

If initialization cannot be finished normally, disconnect SST from the DLC3 and turn the engine switch off. Then, restart from procedure 1.



Result:
Result Proceed to
OK TURN ENGINE SWITCH OFF (END)
NG GO TO PROBLEM SYMPTOMS TABLE




ADJUST STEERING ANGLE SENSOR


NOTICE:

If the steering angle sensor neutral point storage is required, the AFS ECU outputs DTC B2421 and the AFS does not operate normally.


a.

AUTO neutral point storage.

i.

When driving 100 m or more at a speed of 20 to less than 80 km/h on a road with few turns, curves, or traffic, the steering sensor neutral point storage is automatically performed.



b.

MANUAL neutral point storage.

HINT:
·

Perform the AFS OFF switch operation at approximately 1 second intervals.

·

Perform the steering wheel operation within 20 seconds while the neutral point storage is performed.



i.

Preparation

1.

Drive the vehicle and set the steering wheel straight ahead.

2.

Move the shift lever to P or N and apply the parking brake so that the vehicle does not move with the engine running.



ii.

Step 1

1.

Press the AFS OFF switch 8 times with the steering wheel straight ahead.

OK:

AFS OFF indicator blinks.


2.

Wait for 2 seconds.



iii.

Step 2

1.

Press the AFS OFF switch 2 times with the steering wheel fully turned to the left or right.

OK:

AFS OFF indicator illuminates for 2 seconds after blinking, and then blinks again.




iv.

Step 3

1.

After the AFS OFF indicator starts blinking again, press the AFS OFF switch 2 times with the steering wheel fully turned to the right or left.

OK:

AFS OFF indicator illuminates for approximately 2 seconds after blinking, and then blinks again.




v.

Step 4

1.

After the AFS OFF indicator starts blinking again, return the steering wheel back to the straight-ahead position. Then press the AFS OFF switch 2 times.

OK:

AFS OFF indicator illuminates for approximately 2 seconds after blinking, and then turns off.