Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) J

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  Speed Signal Circuit  


DESCRIPTION

The headlight leveling ECU assembly receives the vehicle speed signal from the combination meter assembly.

WIRING DIAGRAM

E349362E03
1.958,0.948 2.271,1.146 0.313,0.198 10 false +S 4.917,0.948 5.479,1.177 0.563,0.229 10 false SPDR 2.208,0.844 2.521,1.042 0.313,0.198 10 false 40 4.677,0.854 4.99,1.052 0.313,0.198 10 false 16 1.271,1.573 1.583,1.771 0.313,0.198 10 false G28 1.271,1.781 2.594,2.208 1.323,0.427 10 false Combination Meter Sub-assembly 4.656,1.531 4.969,1.729 0.313,0.198 10 false A39 4.635,1.729 5.917,2.25 1.281,0.521 10 false Headlight Leveling ECU Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / HL AutoLeveling / Data List.


e.

Read the Data List according to the display on the GTS.

HL AutoLeveling
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/0.00 to 327.67 km/h (203.61 mph) Condition can be displayed -

OK:

Normal condition listed above is displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E358407E01
1.5,0.25 1.917,0.5 0.417,0.25 0.635,1.802 0.74,1.313 false 0.115,0.094 0.615,0.354 0.5,0.26 10 false *a 1.573,0.292 2.073,0.552 0.5,0.26 10 false G28 0.5,1.823 1,2.083 0.5,0.26 10 false +S 2.729,3.729 3.229,3.99 0.5,0.26 10 false GND 0.99,3.969 1.49,4.229 0.5,0.26 10 false (A)

Check the output waveform.

i.

Remove the combination meter assembly with the connector still connected.


ii.

Connect an oscilloscope to terminal G28-40 (+S) and body ground.


iii.

Turn the engine switch on (IG).


iv.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.





OK

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the G28 combination meter assembly connector.


b.

Disconnect the A39 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-16 (SPDR) - G28-40 (+S) Always Below 1 Ω
A39-16 (SPDR) or G28-40 (+S) - Body ground Always 10 kΩ or higher




OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR