Home › Vehicle Interior › LIGHTING › LIGHTING SYSTEM(for LED Headlight) › from 2016.05
RM24M0E _58 Vehicle Interior _059564 LIGHTING _0291968 LIGHTING SYSTEM(for LED Headlight) C

LIGHTING  LIGHTING SYSTEM(for LED Headlight)  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU.

DTC No. DTC Detection Condition Trouble Area
B2430 Any of the following conditions occur after 20 seconds have elapsed since the engine switch was turned on (IG):
·

Light control ECU LH malfunction

·

Headlight unit LH malfunction

·

Light control ECU LH power source and signal malfunction


·

Light control ECU LH

·

Headlight unit assembly LH

·

Headlight assembly LH

·

H-LP relay

·

Harness or connector

·

Main body ECU


B2431 Any of the following conditions occur after 20 seconds have elapsed since the engine switch was turned on (IG):
·

Light control ECU RH malfunction

·

Headlight unit RH malfunction

·

Light control ECU RH power source and signal malfunction


·

Light control ECU RH

·

Headlight unit assembly RH

·

Headlight assembly RH

·

H-LP relay

·

Harness or connector

·

Main body ECU



WIRING DIAGRAM

E349344E03
6.313,0.531 6.927,0.729 0.615,0.198 10 false HRLY 4.74,0.531 5.354,0.729 0.615,0.198 10 false 4L 4.771,0.323 5.385,0.521 0.615,0.198 10 false 6 3.677,1.26 4.292,1.458 0.615,0.198 10 false H-LP 1.198,0.521 2.073,0.781 0.875,0.26 10 false from Battery 6.333,2.615 6.948,2.813 0.615,0.198 10 false RLEW 6.333,5.75 6.948,5.948 0.615,0.198 10 false LLEW 5.948,2.594 6.563,2.792 0.615,0.198 10 false G58 5.948,5.729 6.563,5.927 0.615,0.198 10 false G60 6.01,2.385 6.625,2.583 0.615,0.198 10 false 6 6.01,5.542 6.625,5.74 0.615,0.198 10 false 1 3.438,1.917 4.052,2.115 0.615,0.198 10 false H-LP RL 3.438,5.177 4.052,5.375 0.615,0.198 10 false H-LP LL 2.958,1.677 3.573,1.875 0.615,0.198 10 false B 3.177,1.677 3.792,1.875 0.615,0.198 10 false 4 2.948,2.469 3.563,2.667 0.615,0.198 10 false S 3.177,2.469 3.792,2.667 0.615,0.198 10 false 2 3.188,2.688 3.802,2.885 0.615,0.198 10 false 8 2.948,2.688 3.563,2.885 0.615,0.198 10 false E 1,3.135 2.406,3.344 1.406,0.208 10 false Headlight Unit RH 0.948,6.333 2.354,6.542 1.406,0.208 10 false Headlight Unit LH 0.688,3.938 1.302,4.135 0.615,0.198 10 false B30 1.031,3.938 2.563,4.115 1.531,0.177 10 false Headlight Assembly RH 0.75,6.75 2.49,6.927 1.74,0.177 10 false Headlight Unit Assembly LH 3.177,4.99 3.792,5.188 0.615,0.198 10 false 4 2.969,4.99 3.583,5.188 0.615,0.198 10 false B 3.188,5.615 3.802,5.813 0.615,0.198 10 false 2 2.979,5.625 3.594,5.823 0.615,0.198 10 false S 3.198,5.823 3.813,6.021 0.615,0.198 10 false 8 2.979,5.823 3.594,6.021 0.615,0.198 10 false E 5.979,7.083 7.042,7.438 1.063,0.354 10 false Main Body ECU 4.198,0.448 4.813,0.646 0.615,0.198 10 false 1 4.208,0.875 4.823,1.073 0.615,0.198 10 false 3 3.365,0.417 3.979,0.615 0.615,0.198 10 false 2 3.375,0.875 3.99,1.073 0.615,0.198 10 false 5 0.802,3.563 2.656,3.781 1.854,0.219 10 false Headlight Unit Assembly RH 0.708,7.167 1.323,7.365 0.615,0.198 10 false B31 1.063,7.167 2.802,7.344 1.74,0.177 10 false Headlight Assembly LH 2.729,4.99 3.344,5.188 0.615,0.198 10 false 1 2.74,5.635 3.354,5.833 0.615,0.198 10 false 7 2.74,5.833 3.354,6.031 0.615,0.198 10 false 5 2.719,1.688 3.333,1.885 0.615,0.198 10 false 1 2.708,2.51 3.323,2.708 0.615,0.198 10 false 7 2.719,2.698 3.333,2.896 0.615,0.198 10 false 5 1.438,2.01 2.365,2.667 0.927,0.656 10 false Light Control ECU RH 1.469,5.125 2.469,5.646 1,0.521 10 false Light Control ECU LH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Turn the light control switch to the head position and wait for 20 seconds or more.

HINT:

DTC B2430 and B2431 cannot be detected until 20 seconds have elapsed since the engine switch was turned on (IG).



c.

Check for DTCs (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>DTC CHECK / CLEAR).

Result:
Result Proceed to
Both DTC B2430 and B2431 are not output A
Both DTC B2430 and B2431 are output B
DTC B2430 or B2431 is output C




A

B

2.INSPECT H-LP RELAY

C

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY)
2.INSPECT H-LP RELAY
a.
E316295E06
2.531,1.208 2.625,1.135 false 2.917,0.958 3.021,1.021 false 2.615,1.542 2.719,1.417 false 2.25,1.344 2.25,1.469 false 0.385,0.844 0.698,1.146 0.313,0.302 11 false 3 2.427,1.156 2.74,1.458 0.313,0.302 10 false 3 2.229,1.49 2.542,1.792 0.313,0.302 10 false 2 1.625,0.854 1.938,1.156 0.313,0.302 11 false 5 0.385,1.26 0.698,1.563 0.313,0.302 11 false 2 1.615,1.271 1.927,1.573 0.313,0.302 11 false 1 2.813,0.833 3.125,1.135 0.313,0.302 10 false 1 2.708,1.25 3.021,1.552 0.313,0.302 10 false 5 0.156,0.135 0.604,0.323 0.448,0.188 10 false *a

Remove the H-LP relay from the No. 2 engine room relay block and No. 2 junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage applied between terminals 1 and 2 Below 1 Ω


Text in Illustration
*a Component without harness connected
(H-LP relay)



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RELAY)

NG

REPLACE H-LP RELAY

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connector Condition Specified Condition
2 (H-LP relay terminal) - Body ground Always 11 to 14 V
5 (H-LP relay terminal) - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (H-LP RELAY - HEADLIGHT ASSEMBLY LH AND HEADLIGHT ASSEMBLY RH)
a.

Disconnect the B31 headlight assembly LH connector.


b.

Disconnect the B30 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP relay terminal) - B30-4 (B) Always Below 1 Ω
3 (H-LP relay terminal) - B31-4 (B) Always Below 1 Ω
3 (H-LP relay terminal) or B30-4 (B) - Body ground Always 10 kΩ or higher
3 (H-LP relay terminal) or B31-4 (B) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (H-LP RELAY - MAIN BODY ECU)
a.

Disconnect the 4L main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP relay terminal) - 4L-6 Always Below 1 Ω
1 (H-LP relay terminal) or 4L-6 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - H-LP RELAY)
a.

Disconnect the B31 headlight assembly LH connector or the B30 headlight assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (DTC B2430)
Tester Connection Condition Specified Condition
B31-4 (B) - Body ground Light control switch in head position 11 to 14 V

RH Side (DTC B2431)
Tester Connection Condition Specified Condition
B30-4 (B) - Body ground Light control switch in head position 11 to 14 V




OK

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (DTC B2430)
Tester Connection Condition Specified Condition
B31-8 (E) - Body ground Always Below 1 Ω

RH Side (DTC B2431)
Tester Connection Condition Specified Condition
B30-8 (E) - Body ground Always Below 1 Ω




OK

8.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL ECU SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (LIGHT CONTROL ECU SIGNAL)
a.

Check the waveform.

OK:
LH Side (DTC B2430)
Tester Connection Condition Specified Condition
B31-2 (S) - Body ground Engine switch on (IG), light control switch in head position Pulse generation

RH Side (DTC B2431)
Tester Connection Condition Specified Condition
B30-2 (S) - Body ground Engine switch on (IG), light control switch in head position Pulse generation




OK

9.INSPECT HEADLIGHT CORD

NG

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
9.INSPECT HEADLIGHT CORD
a.

Remove the headlight code from the headlight assembly (See page Vehicle Interior>LIGHTING>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).




OK

10.REPLACE HEADLIGHT ASSEMBLY

NG

REPLACE HEADLIGHT CORD

10.REPLACE HEADLIGHT ASSEMBLY
a.

Replace the headlight assembly with a new or known good one (See page Vehicle Interior>LIGHTING>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).



NEXT

11.CHECK DTC
11.CHECK DTC

b.

Turn the engine switch off and wait for 30 seconds or more.


c.

Turn the light control switch to the head position and wait for 20 seconds or more.

HINT:

DTC B2430 and B2431 cannot be detected until 20 seconds have elapsed since the engine switch was turned on (IG).



d.

Check for DTCs (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 is not output.




A

END (HEADLIGHT ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU

12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
a.

Disconnect the G58 and G60 main body ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (DTC B2430)
Tester Connection Condition Specified Condition
G60-1 (LLEW) - B31-2 (S) Always Below 1 Ω
G60-1 (LLEW) or B31-2 (S) - Body ground Always 10 kΩ or higher

RH Side (DTC B2431)
Tester Connection Condition Specified Condition
G58-6 (RLEW) - B30-2 (S) Always Below 1 Ω
G58-6 (RLEW) or B30-2 (S) - Body ground Always 10 kΩ or higher




OK

13.INSPECT HEADLIGHT CORD

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT HEADLIGHT CORD
a.

Remove the headlight code from the headlight assembly (See page Vehicle Interior>LIGHTING>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).




OK

14.REPLACE HEADLIGHT ASSEMBLY

NG

REPLACE HEADLIGHT CORD

14.REPLACE HEADLIGHT ASSEMBLY
a.

Replace the headlight assembly with a new or known good one (See page Vehicle Interior>LIGHTING>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL).



NEXT

15.CHECK DTC
15.CHECK DTC

b.

Turn the engine switch off and wait for 30 seconds or more.


c.

Turn the light control switch to the head position and wait for 20 seconds or more.

HINT:

DTC B2430 and B2431 cannot be detected until 20 seconds have elapsed since the engine switch was turned on (IG).



d.

Check for DTCs (See page Vehicle Interior>LIGHTING>LIGHTING SYSTEM(for LED Headlight)>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 is not output.




A

END (HEADLIGHT ASSEMBLY WAS DEFECTIVE)

B

REPLACE MAIN BODY ECU