Home › Vehicle Interior › WIPER / WASHER › FRONT WIPER MOTOR
RM24M0E _58 Vehicle Interior _059565 WIPER / WASHER _0291976 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 75534 2.REMOVE WINDSHIELD MOULDING OUTSIDE LH

Hide 75533 3.REMOVE WINDSHIELD MOULDING OUTSIDE RH

HINT:

Use the same procedure as for the LH side.


Hide 85192 4.REMOVE FRONT WIPER ARM HEAD CAP

B145120

a.

Remove the 2 caps.


Hide 85221B 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

B145121

a.

Remove the nut and arm and blade.


Hide 85211B 6.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

B145122

a.

Remove the nut and arm and blade.


Hide 53867H 7.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

B145940E01
1.161,2.564 1.297,2.724 0.136,0.161 10 A 2.893,2.571 3.012,2.718 0.119,0.147 10 B

a.

When planning to reuse the front fender to cowl side seal:

i.

Detach the clip labeled A. Then partially remove the front fender to cowl side seal.

HINT:

It is not necessary to fully remove the front fender to cowl side seal. Partially remove it so that the cowl top ventilator can be removed later.




b.

When replacing the front fender to cowl side seal:

i.

Detach the claw and clip and remove the front fender to cowl side seal.



Hide 53866J 8.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

B145941E01
2.182,2.551 2.344,2.721 0.163,0.170 10 A 0.532,2.578 0.673,2.741 0.141,0.163 10 B

a.

When planning to reuse the front fender to cowl side seal:

i.

Detach the clip labeled A. Then partially remove the front fender to cowl side seal.

HINT:

It is not necessary to fully remove the front fender to cowl side seal. Partially remove it so that the cowl top ventilator can be removed later.




b.

When replacing the front fender to cowl side seal:

i.

Detach the claw and clip and remove the front fender to cowl side seal.



Hide 55781F 9.REMOVE COWL TOP VENTILATOR LOUVER

a.
B145939

Remove the washer hose front the ventilator louver.


b.
B145123

Remove the 2 clips.


c.
B460066

Detach the 6 claws and remove the louver.


Hide 47233 10.REMOVE BRAKE MASTER CYLINDER RESERVOIR BRACKET

a.
B145931

Remove the 2 bolts.


b.

Remove the brake master cylinder reservoir bracket.


Hide 55712 11.REMOVE FRONT COWL TOP OUTSIDE PANEL WITH WINDSHIELD WIPER MOTOR AND LINK

a.
B145932

Disconnect the connector.


b.
B145933

Remove the 10 bolts and remove the front cowl top outside panel.


Hide 85160 12.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

B145934

a.

Remove the 2 wiper grommets.


b.
B460067E01
0.448,1.906 1.021,2.135 0.573,0.229 10 true : Clmp

Remove the 4 bolts.


c.

Detach the clamp and remove the front wiper motor and link.


Hide 13.REMOVE FRONT WIPER CRANK SUB-ASSEMBLY

a.
E168932E01
0.089,0.113 0.728,0.489 0.639,0.375 10 Protective Tape 1.182,0.727 0.987,0.218 0.987,0.218 0.894,0.218 false

Using a screwdriver, separate the windshield wiper link rod from the crank arm pivot of the front wiper crank sub-assembly as shown in the illustration.

HINT:

Tape the screwdriver tip before use.



b.
E168933

Remove the nut and the front wiper crank sub-assembly.


Hide 85110 14.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

a.
B145937E02
0.479,1.917 0.917,2.094 0.438,0.177 10 false Clamp

Detach the clamp.


b.

Remove the 3 bolts and wiper motor.