Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side)
RM24M0E _58 Vehicle Interior _059567 SEAT _0291993 REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Stowing Seat Type RH Side)  INSTALLATION  


PROCEDURE

Hide 79030 1.INSTALL NO. 3 SEAT LEG ASSEMBLY RH

a.
B141722

Engage the seat leg to the floor front side stud bolt hole.


Hide 2.INSTALL REAR NO. 2 SEAT ASSEMBLY RH

a.
B148192E03
0.531,0.521 0.969,0.698 0.438,0.177 10 false Center

Place the seat onto the lock striker.


b.

Fully lock the seat to the lock striker.


c.

Connect the connector.

HINT:
·

Confirm that the seat is firmly locked to the lock striker.

·

The rear leg should be set to the center of the lock striker.




d.
B141721E02
1.137,1.578 1.293,1.760 0.156,0.181 10 1 1.979,1.55 2.135,1.731 0.156,0.181 10 2 2.466,1.418 2.622,1.599 0.156,0.181 10 3 2.93,1.212 3.086,1.393 0.156,0.181 10 4

Temporarily install bolt 1.


e.

Install bolt 4.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


f.

Tighten bolt 1.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


g.

Install nut 2.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


h.

Install nut 3.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


i.
B147573E02
2.823,0.958 3.26,1.135 0.438,0.177 10 true 2.3mm

Adjust the seat leg and stopper clearance as shown in the illustration.

Standard clearance:

2.3 mm (0.091 in.)



j.
B148182E01
0.232,1.367 1.168,1.714 0.936,0.348 10 Surfaces are not aligned 1.452,1.643 2.217,1.548 false

If the lower surface of the stopper is not aligned with the seat leg:

i.

Connect cable to negative battery terminal.


ii.

Lift the lever (A) shown in the illustration and press the button on the fold seat switch, indicated by the arrow in the illustration, to adjust the alignment.

B148184E02
1.469,1.781 1.896,2.198 false 1.896,2.156 2.052,2.333 0.156,0.177 10 false A 5.573,0.729 6.635,0.906 1.063,0.177 10 false Fold Seat Switch 4.49,0.74 4.927,0.917 0.438,0.177 10 false 2.3mm

Standard clearance:

2.3 mm (0.091 in.)




k.
B148183E01
1.565,0.928 1.565,0.401 false 1.559,0.401 1.96,0.401 false 2.04,0.21 2.976,0.558 0.936,0.348 10 Surfaces are not aligned

If the lower surface of the stopper is not aligned with the seat leg:

i.

Connect cable to negative battery terminal.


ii.

Press the button on the fold seat switch, indicated by the arrow in the illustration, to adjust the alignment.

B148185E01
4.439,0.546 4.881,0.727 0.441,0.181 10 2.3mm 5.56,0.644 6.619,0.825 1.059,0.181 10 Fold Seat Switch

Standard clearance:

2.3 mm (0.091 in.)




l.
B148191E03
1.156,0.458 1.313,0.635 0.156,0.177 10 true 1 1.26,0.76 1.417,0.938 0.156,0.177 10 true 2 2.979,0.271 3.135,0.448 0.156,0.177 10 true 3 1.927,0.385 2.083,0.563 0.156,0.177 10 true 5 2.052,0.646 2.208,0.823 0.156,0.177 10 true 6 2.417,0.323 2.573,0.5 0.156,0.177 10 true 7 2.49,0.542 2.646,0.719 0.156,0.177 10 true 8 2.99,0.51 3.146,0.688 0.156,0.177 10 false 4

While pressing against the arms of the seat legs, tighten the bolts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

NOTICE:

If the seat leg and stopper surfaces are not aligned properly, the lock will malfunction when the seat is operated.



m.
B462498E01
0.979,0.813 0.604,0.813 true 1.156,1.646 0.729,1.646 0.729,1.646 0.729,0.813 true 0.167,0.729 0.625,0.938 0.458,0.208 10 false Clamp

Attach the 2 clamps to install the seat leg.


Hide 79273 3.INSTALL NO. 2 SEAT HINGE COVER

a.
B139135

Attach the 4 claws.


b.

Attach the 4 clips to install the hinge cover.


Hide 79374 4.INSTALL NO. 3 SEAT LEG COVER REAR RH

a.
B139137

Attach the 6 claws to install the 2 leg covers.


Hide 79236A 5.INSTALL NO. 2 SEAT LEG COVER

a.
B139136

Attach the 2 claws.


b.

Attach the 2 clips to install the hinge cover.


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 7.CHECK REAR NO. 2 SEAT STOWING FUNCTION (for Power Seat Type RH Side)

Hide 8.PERFORM INITIALIZATION

a.

Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.