Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM L

DOOR LOCK  SMART ENTRY AND START SYSTEM  PRECAUTION  


NOTICE:

When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected.


System Name See procedure
Lighting System (Click here)
Parking Assist Monitor System
Power Slide Door System
Power Back Door System

PRECAUTIONS WHEN USING INTELLIGENT TESTER


a.

When using the intelligent tester to troubleshoot the LIN communication line: Connect the intelligent tester to the vehicle, and turn a courtesy light switch on and off at 1.5 second intervals until communication between the tester and vehicle begins.


b.

After all DTCs are cleared, check if the trouble occurs again 6 seconds after the engine switch is turned on (IG).



PRECAUTIONS FOR EACH FUNCTION


a.

Precautions for the key:

The key is a precision instrument. Be sure to observe the following:

i.

Do not drop or strike the key.


ii.

Do not keep the key in a high temperature area for a long time.


iii.

Do not use an ultrasonic washing machine to clean the key.


iv.

Keep the key away from magnets or magnetized items during use.


v.

Do not attach any stickers to the key.



b.

Precautions for the entry unlock function:

i.

As the sensor is built into the backside of the outside door handle, the user must touch the backside part of the handle when performing the unlock function.


ii.

If touched with gloved hands, the response of the door may be delayed.


iii.

During the entry unlock operation, if the door handle is pulled before the door unlocks, the unlock function cannot be completed. Confirm that the door has been unlocked before pulling the door handle to open the door.


iv.

Make sure that the doors are unlocked when touching the touch sensor on the outside door handle while the key is being carried.

If the doors cannot be unlocked, the certification ECU orders each door ECU to perform the door unlock operation 4 times.

At this time the door may not be unlocked because the handle is being pulled due to some mechanical reasons.

Be sure to return the door handle to its original position.

If the door cannot be opened by pulling the handle, perform the entry unlock operation again.


v.

If the key is too close to the oscillator on the outside of the vehicle, the door may not be unlocked because the key cannot react to the strong wave output from the transmitter.


vi.

If the key is within the vehicle exterior detection area, the door can be unlocked even when a person other than the person carrying the key holds the door handle.

However, the doors other than the door that the codes match will not be unlocked.

(If the key is within the driver side door's detection area outside the vehicle, the doors will be unlocked when the person carrying the key holds the driver side door handle. However, if any door handle other than that of the driver side door is held, the doors will not be unlocked).


vii.

If a door is not opened after the door unlock operation, the doors automatically lock after approximately 30 seconds.


viii.

If a large amount of water is applied to the door handle due to a car wash or heavy rain, and the key is brought within the vehicle exterior detection area, it may cause the doors to be unlocked.

However, the doors will be locked again after approximately 30 seconds if a door is not opened.


ix.

If the key of the smart entry and start system is used while it is being carried with the key of another smart entry and start system, the time before the entry unlock operation will become longer than usual. This is not a malfunction.



c.

Precautions for the entry lock function:

i.

When performing the entry lock operation, firmly press the lock switch on the outside door handle.

If pressed too quickly or lightly, the entry lock may not operate.


ii.

It is possible that signals output from the indoor electrical key oscillator may leak through the window. Also, if the key is too close to a door electrical key oscillator, the oscillator output signals are too strong and the key cannot respond. As a result, when the key is near the vehicle interior (window, door handle), the entry lock function may not operate. Also, the warning buzzer may sound and the entry lock operation may stop functioning. In this situation, move the key away from the vehicle interior (window, door handle), perform the entry lock operation and perform the entry unlock operation.


iii.

Do not touch the lock switch while opening or closing the door.

If the lock switch is pressed when opening or closing the door while the key is being carried, the door ajar warning buzzer sounds. (Beeps outside the vehicle for 5 seconds.)


iv.

If the key is on the instrument panel, rear package tray or floor, or in the glove box, the key reminder function may not operate and the key may be locked in the vehicle. Always carry the key.


v.

If the key is outside the vehicle but is very close to a window or door handle (the ECU determines that the key is inside the vehicle) and the transmitter or mechanical key is used to lock the doors (entry lock is not used), entry unlock will not operate. To unlock the doors, perform a wireless door unlock operation. The entry lock function operates in this way to prevent the user from unintentionally unlocking the doors from outside the vehicle. For example, when a user operates the wireless door lock operation from inside the vehicle, radio waves from a door electrical key oscillator may leak into the vehicle interior and the doors may unlock.


vi.

To allow the user enough time to check if the doors are locked after performing a door lock operation (entry lock function or wireless door lock operation), the entry unlock function will not be permitted for 3 seconds after the door lock operation.



d.

Precautions for the entry ignition function:

i.

To start the engine, first depress the brake pedal firmly until the engine switch indicator illuminates in green.


ii.

When operating the engine switch, firmly press the switch. If the switch is pressed too quickly, power source control and engine starting may not operate.


iii.

While driving the vehicle, continuously pressing the engine switch for 3 times quickly or pressing and holding the engine switch for 2 seconds or more will turn off the engine. Do not touch the engine switch while driving, except in an emergency.


iv.

Do not touch the engine switch with oily hands.


v.

If the vehicle has been in a hot location for an extended period of time, be careful when touching the engine switch. It may be very hot and lead to burns.


vi.

Take care to avoid spilling beverages on the engine switch. Keep all liquids away from the engine switch.


vii.

Do not use the engine switch if it seems to be sticking or feels abnormal.


viii.

The vehicle continually records the power source mode (off, on (ACC), on (IG), start). When the battery cable is disconnected and reconnected, the power source mode will return to the mode it was in before disconnecting the battery cable. Always disconnect the battery cable before turning the power off. When the vehicle battery is fully depleted, power is cut, and the power source mode before the power was cut is unknown, so be extremely careful.


ix.

Do not connect any electronic products to the ACC, IG1 or IG2 coil side wiring, as the vehicle power supply may be unable to be turned on, or other problems may occur.


x.

After the battery cable has been disconnected and reconnected, the engine will not start on the first attempt. The engine will start normally on the second attempt.


xi.

When starting the engine immediately after reconnecting the battery cable, connect the cable and wait at least 10 seconds before attempting to start the engine. The engine may not start when attempting an engine start immediately after disconnecting and reconnecting the battery cable.


xii.

If the key battery is depleted and the engine is started by holding the key close to the engine switch, warnings will sound when certain conditions are met.

HINT:

When the key battery is depleted, the vehicle cannot determine if the key is in the vehicle or not. This is not a malfunction.

·

Driver door open → closed:

Shift lever P position power source cut reminder exit warning, or shift lever other than P position power source cut reminder exit warning

·

Door other than driver door open → closed:

Passenger leaves with key warning





e.

Precautions for back door entry function:

Even if the key is within the back door electrical key antenna (outer) detection area, the back door cannot be opened if the key is in the following areas:

·

Near the center of the tuner

·

Too close to the ground or in a high place



f.

Precautions for the battery built into the key and the vehicle battery:

i.

The key is constantly checking for signals from the vehicle, which requires power from the key's built-in battery. The life of the battery is approximately 1 to 2 years depending on the usage conditions. Be sure to replacing the battery when its power is low. When replacing the battery, do not touch the inner circuit board or other inner parts.


ii.

The key is constantly checking for signals from the vehicle and using battery power, whether the key is being used or not. Even if the user is carrying 2 keys and only 1 key is used, both keys will consume battery power.


iii.

The key receives radio waves at approximately 134kHz. If the key continuously receives strong, identical frequency waves, this may drain the key's battery. Store the key at least 1 m (3.3 ft.) from TVs, personal computers, or other electrical products.


iv.

When the door is being locked, the vehicle battery is used to transmit radio waves. The key sends radio waves at RF 433.92 MHz (*1) and 315.12 MHz (*2). The battery may be dead if the vehicle remains stopped for a long time. If the vehicle is not used for a long time, remove the battery from the vehicle or cancel the smart entry and start system.

HINT:
·

*1: Middle East

·

*2: General Countries




v.

When the door is being locked with the key in the detection area of a door electrical key oscillator, the battery is used for regular communication between the key and vehicle. If the vehicle is not used, keep the key away from the vehicle (more than 2 m (6.6 ft.)).


vi.

After disconnecting and reconnecting the battery cable, the entry unlock function may not operate. If this occurs, perform a wireless door unlock and lock operation.




PRECAUTION FOR STEERING LOCK ACTUATOR


NOTICE:

If the steering lock actuator (steering lock ECU) is replaced, open and close the driver side door to record the current steering lock position into the certification ECU. If this is not performed, the engine may not start.