Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM › 2013.04–2016.05
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM D

DOOR LOCK  SMART ENTRY AND START SYSTEM  SYSTEM DESCRIPTION  


CAUTION:

If using a pacemaker, be sure to read the manual of the pacemaker before using the key, as the radio waves of the key may affect the pacemaker.


SMART ENTRY AND START SYSTEM


a.

In addition to conventional mechanical key and wireless door lock control functions, the smart entry and start system enables door locking/unlocking, steering lock releasing, engine starting and back door opening without operating the key. The only requirement is that the key is in the user's possession.

·

This system is controlled by the certification ECU. When the certification ECU detects the presence of the smart entry and start system in one of the detection areas, it identifies and checks the ID code, and outputs operation signals to the related ECU in accordance with their functions.

·

The detection areas are formed by 2 oscillators and 4 antennas (2 door oscillators, back door antenna (for outer), 3 indoor antennas).




DETECTION AREA


B128912E04
0.149,2.313 1.187,2.478 1.039,0.166 10 Detection Area 0.252,3.281 2.172,3.456 1.92,0.175 10 Door Electrical Key Oscillator 0.059,5.213 2.932,5.416 2.872,0.203 10 Back Door Electrical Key Antenna (for Outer) 0.054,1.009 1.847,1.371 1.793,0.362 10 Approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) 4.583,4.826 6.376,5.188 1.793,0.362 10 Approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) 2.884,1.92 4.197,2.326 1.313,0.406 10 Indoor Electrical Key Antenna (for Front) 2.889,2.835 4.191,3.213 1.302,0.378 10 Indoor Electrical Key Antenna (for Rear1) 2.875,3.592 4.205,3.933 1.33,0.341 10 Indoor Electrical Key Antenna (for Rear2) 5.615,0.631 7.085,0.977 1.47,0.345 10 Front Seat, Rear Seat, Luggage Space Areas 5.952,1.748 7.145,2.099 1.193,0.351 10 Key (Door Control Transmitter) 3.296,0.062 3.75,0.271 0.454,0.209 10 Front 1.778,2.07 1.179,2.416 false 2.463,2.056 2.07,3.254 false 4.876,3.281 6.795,3.456 1.92,0.175 10 Door Electrical Key Oscillator 4.587,2.056 4.98,3.254 false 3.458,4.244 1.572,5.213 false 3.529,1.806 3.529,1.92 false 3.529,2.69 3.529,2.835 false 3.529,3.472 3.529,3.592 false 3.973,1.341 5.542,0.734 false 5.415,1.931 5.912,1.832 false 3.441,5.442 3.795,5.605 0.354,0.163 10 Rear

a.

Precautions for the entire system:

·

Be sure to carry the key during inspection of the smart entry and start system.

·

As weak radio waves are used to detect the key, the key detection area may decrease, or the key may not be detected correctly in the following situations:

(a)

The key battery is depleted.

(b)

Any facilities that generate strong radio waves, such as a TV tower, power plant, broadcast station or gas station, are located near the inspection site.

(c)

A wireless device, such as a cellular phone, is carried with the key.

(d)

The key is in contact with or covered with metal.

(e)

Another wireless door lock control function is operated near the vehicle.

(f)

The key is located near a device that generates high voltage or noise.



·

The key may be difficult to operate for a reason relating to the vehicle body shape.

·

The key may not be detected correctly if it is around the vehicle's windows, the door handle or center of the bumper even when it is in the detection area outside the vehicle.

·

The key may not be detected correctly if it is on the instrument panel, rear package tray or floor, or in the glove box even when it is in the detection area inside the vehicle.

·

The key may not operate if the key is not held properly.

·

The smart entry and start system does not operate in the following conditions:

(a)

The smart entry and start system is canceled.

(b)

The key battery is completely depleted (the indicator does not blink when pushing any of the buttons on the key).





FUNCTION OF MAIN COMPONENTS


Components Function
Key
·

When LF wave*1 that is output from vehicle interior / exterior antenna is received, RF wave*2 format conversion is performed on key ID, vehicle ID and other information, and RF wave*2 is then output

·

When key's lock / unlock button is pressed, signal is converted to RF wave*2 and is then output

·

When the wave output from the engine switch's immobiliser amplifier is received, key ID, vehicle ID and other information is output through immobiliser communication

·

Has mechanical key for unlocking doors when the battery is dead


Certification ECU Controls smart entry and start system in accordance with signals from each oscillator, various switches, ECUs and key
·

Performs key verification

·

Performs vehicle interior / exterior transmission

·

Performs occupant sensor control

·

Sends lock / unlock commands during entry function

·

Sends steering lock / unlock commands

·

Sends immobiliser set / unset commands

·

Records verification codes


Main body ECU Controls push button start function in accordance with signals from various switches, ECUs and combination meter
·

Controls ACC / IG power source by turning it ON / OFF

·

Sends engine start command to ECM

·

Controls indicator and word illumination of engine switch

·

Activates starter relay support


ID code box
·

Receives command from certification ECU, and sends immobiliser set / unset command to ECM

·

Records verification codes


Outside door handle (for driver, front passenger side doors) (antenna) Transmits request signals
Outside door handle (for driver, front passenger side doors) (touch sensor) Detects when person touches inside of outside handle
Outside door handle (for driver, front passenger side doors) (lock switch) Transmits door lock request signals to certification ECU
Door electrical key oscillator (for driver, front passenger side doors) Receives request signal from certification ECU, and forms detection area around each door
Indoor electrical key antenna (for front, rear1 and rear2) Receives request signal from certification ECU, and forms detection area in vehicle interior
Back door electrical key antenna (for outer) Receives the request signal from the certification ECU, and forms the actuation area around the back door
Door control receiver Receives the ID code from the key in the actuation area and transmits it to the certification ECU
Back door open switch Transmits a back door open request signal to the main body ECU
Back door lock switch Transmits a back door lock request signal to the certification ECU
Stop light switch Outputs state of brake pedal to main body ECU
Wireless door lock buzzer When certification ECU detects human errors such as those below, it warns driver by sounding wireless door lock buzzer and sounds the buzzer in accordance with request signal from ECU
Example:
·

Key is taken outside vehicle

·

Driver leaves vehicle while engine is still running


Combination meter
·

Buzzer



HINT:
·

*1: LF waves check if the key is in the vehicle interior or not.

·

*2: RF waves are emitted from the key in response to the LF waves, and are sent to the door control receiver.




CONSTRUCTION AND OPERATION


HINT:
·

*1: LF radio waves check if the key is in the vehicle interior or not.

·

*2: RF radio waves are emitted from the key in response to the LF radio waves, and are sent to the door control receiver.



a.

Key:

The key consists of a mechanical key, transmitter for the wireless door lock remote control, and transceiver for the smart entry and start system.

·

Upon receiving the LF radiowaves*1 that are output by the vehicle interior and exterior antennas, the door control transmitter outputs information including the key ID and vehicle ID by modulating then into RF radiowaves*2.

·

When the drive presses the lock or unlock switch on the surface of the door control transmitter, the transmitter outputs the description of the operation by modulating it into RF radiowaves*2.

·

Upon receiving the radiowaves that are output by the immobiliser amplifier in the engine switch, the door control transmitter outputs information including the key ID and vehicle ID through immobiliser communication.

·

Has a built-in mechanical key to unlock the door if the transmitter battery is low.


A total of 5 keys can be registered.

B128913E06
5.75,1.854 6.021,1.604 false 5.073,1.198 4.333,1.74 false 4.521,0.99 3.771,0.792 false 4.604,0.844 4.198,0.313 false 4.865,0.854 5.281,0.438 false 4.875,0.99 5.729,0.823 false 6.083,1.521 7.083,1.75 1,0.229 10 false Mechanical Key 3.354,0.208 4.208,0.354 0.854,0.146 10 false LOCK Switch 5.792,0.771 6.844,0.917 1.052,0.146 10 false UNLOCK Switch 2.406,0.719 3.875,0.885 1.469,0.167 10 false Left Slide Door Switch 5.323,0.323 6.875,0.5 1.552,0.177 10 false Right Slide Door Switch 2.76,1.646 4.313,1.833 1.552,0.188 10 false Power Back Door Switch


b.

Oscillator (for front LH and RH door oscillators, front, rear1 and rear2 indoor antenna, back door antenna):

Each oscillator transmits the request signal received from the certification ECU, and forms a key detection area to detect the presence of a key. The detection area formed by each door electrical key oscillator and back door electrical key antenna is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside handle of the front LH and RH doors or from the center of the rear bumper.

·

The detection area of the front LH and RH door oscillators are formed by transmitting a request signal every 0.25 seconds while the ignition switch is off and each door is locked. In this way, it detects the proximity of a key. During entry lock, the detection area is formed with the lock switch ON.

·

The detection area of the back door electrical key antenna is formed when the back door opener switch is ON.

·

The detection area of the indoor electrical key antenna (for front, rear1 and rear2) is formed when the driver door is opened or closed, during ignition start, when a warning is activated, or when the lock switch is ON. It is formed twice until the key can be verified.

·

The detection area of the front, rear1 and rear2 indoor antennas are formed when the driver door is opened or closed, during ignition start, when a warning is activated, or when the lock switch is ON.




ENTRY FUNCTION OPERATION


a.

The smart entry and start system has the following functions.

Function Outline
Mechanical key Operation is same as conventional mechanical key
Wireless door lock control function This function remotely locks and unlocks all doors or back door. Operation is same as wireless door lock control system. However, the receiver in certification ECU uses entry door control receiver to control locking and unlocking.
Entry illumination function When person carrying key enters detection area, door will enter unlock standby mode and map light and foot light will illuminate
Entry unlock function When key is located in detection area of door oscillator, door will unlock by touching inside of outside door handle
Entry lock function When key is located in detection area of door oscillator and ignition switch is off, door can be locked by pressing lock switch on outside door handle
Key lock-in prevention function Prevents confinement of key if door is locked using outside door handle while key is still inside vehicle
Warning function When any of situations below occur, smart entry and start system causes certification ECU to sound buzzer in combination meter and wireless door lock buzzer in order to alert driver:
·

Shift lever not on P (power source cut reminder) vehicle exit warning

·

Key reminder warning

·

Shift lever on P (power source cut reminder) vehicle exit warning

·

Entry door ajar warning

·

Passenger has brought key out of vehicle warning

·

Key is not within detection area warning

·

Key lock-in prevention function buzzer

·

Key battery low warning


Battery saving function If key is constantly located within detection area of door oscillator, system maintains periodic communication with key. Therefore, if vehicle remains parked in that state for long time, key battery and vehicle battery could be drained.
Key cancel (see page (Click here)) Following key functions can be canceled by following certain operations:
·

Entry ignition

·

Entry unlock / lock function

·

Entry back door open function

·

Key lock-in prevention function

·

Warning function





WIRELESS DOOR LOCK AND UNLOCK AND BACK DOOR OPEN FUNCTION


a.

Push the LOCK/UNLOCK switch on the key to operate each function.



ENTRY UNLOCK FUNCTION


a.

The detection area is formed by communication between a door electrical key oscillator and door control receiver when the door is locked in order to detect access of the person carrying the key.


b.

When the person carrying the key enters the detection area around the vehicle, the matching of the ID codes for a door electrical key oscillator and key will automatically be performed. After the matching is completed, the door will enter unlock standby mode.


c.

In unlock standby mode, the antenna built into the outside handle starts sensing. If the outside handle is held (the back side of the handle is touched), the door unlock operation will be performed. At this time, the hazard warning lights blink twice and the wireless door lock buzzer sounds twice.

HINT:

For Europe, the buzzer does not sound.



d.

If none of the doors are opened within 30 seconds of a door unlock operation, all doors are automatically locked.



ENTRY LOCK FUNCTION


a.

After leaving the vehicle carrying the key, push the lock switch on the outside handle when all the doors are closed.


b.

The certification ECU determines whether the key is located inside or outside of the cabin based on the information from a door electrical key oscillator and indoor electrical key antenna. Then matching of the ID codes is performed.


c.

When the matching result shows that the ID codes of the key and indoor electrical key antenna do not match and the ID codes of the key and door electrical key oscillator match, the door lock function will operate. At this time, the hazard warning lights blink once.


d.

If the key is located inside of the cabin, the door lock function will not operate and the alarm buzzer (beep sound) will sound for 2 seconds.

HINT:

For Europe, the buzzer does not sound.




PREVENTION OF KEY CONFINEMENT FUNCTION


a.

If the user attempts to lock the door through keyless operation (move the lock knob to the lock position and then close the door) with the key in the cabin, the system determines that the key is located in the cabin and unlocks the door.


b.

If the back door is closed with the key in it, the alarm will sound and the back door can be opened only when all the doors are locked in order to prevent key confinement in the vehicle.



ENTRY ILLUMINATION FUNCTION


a.

When a person carrying the key enters the detection area, the door will enter unlock standby mode and the room light and foot light will illuminate.



HINT:

The entry illumination function operates when the key enters the vehicle exterior detection area from out of the detection area. If the key remains in the detection area for 3 seconds or more, the illumination function does not operate.


WARNING FUNCTION


a.

General:

When any of the situations below occur, the smart entry and start system responds to alert the driver.

Warning Function Operation Condition Situation Situation
Shift lever not on P (power source cut reminder) vehicle exit warning A
Key reminder warning B
Shift lever on P (power source cut reminder) vehicle exit warning C
Entry door ajar warning D
Passenger has brought key out of vehicle warning E
Key is not within detection area warning F
Key lock-in prevention function buzzer G
Key battery low warning H


b.

Situation A:

Shift lever not on P (power source cut reminder) vehicle exit warning

i.

With shift lever in position other than P, door is opened and vehicle exit (while holding key) is attempted

Reason for warning: Sudden vehicle start prevention, vehicle theft prevention, vehicle roll-away prevention
Warning start condition: Shift lever position is not P, ignition switch is on (ACC or IG), driver side door is opened and vehicle speed is 0 km/h (0 mph)
Warning stop condition: Ignition switch is on (ACC or IG), shift lever position is P, vehicle speed is above 0 km/h (0 mph), or driver side door is closed
Warning description Combination meter buzzer Short sound buzzer Sounds continuously (beep)
Combination meter display Telltale None
Wireless buzzer None
Recommended user action Move shift lever to P position


ii.

With shift lever in position other than P, door is opened, key is brought out of vehicle, door is closed, and move away from vehicle is attempted

Reason for warning: Sudden vehicle start prevention, vehicle theft prevention, vehicle roll-away prevention
Warning start condition: Shift lever position is not P, ignition switch is on (ACC or IG), opened driver side door is closed, vehicle speed is 0 km/h (0 mph) and key is not in detected in vehicle interior
Warning stop condition:
·

Key is detected in vehicle interior:

Buzzer stops



·

Vehicle speed is above 0 km/h (0 mph):

Buzzer stops and telltale illuminates



·

Ignition switch on (ACC) or off:

All warnings are turned off



Warning description Combination meter buzzer Short sound buzzer Sounds continuously (beep)
Combination meter display Telltale Illuminates
Wireless buzzer Sounds continuously (beep)
Recommended user action Move shift lever to P position



c.

Situation B:

Key reminder warning

i.

With shift lever on P and either ignition switch on (ACC), or steering lock / unlock set, driver door is opened and move away from vehicle is attempted

Reason for warning: Vehicle theft prevention, required by law
Precondition: Remote engine starter is not operating
Warning start condition: With shift lever position in P, one of following conditions is met
1.

Ignition switch on (ACC) or off, and driver door opened

2.

Ignition switch on (ACC) or off, steering lock/unlock set and driver door opened


Warning stop condition: One of following conditions is met
1.

With shift lever position in P, ignition switch is on (IG) or driver door is closed

2.

Ignition switch on (ACC) or off, and steering lock/unlock is set


Warning description Combination meter buzzer Short sound buzzer Sounds intermittently (several short beeps)
Combination meter display Telltale None
Wireless buzzer None
Recommended user action One of following is performed
1.

Turn ignition switch off and close driver door

2.

Close driver door





d.

Situation C:

Shift lever on P (power source cut reminder) vehicle exit warning

i.

Pattern 1: With shift lever on P, driver door is opened, key is brought out of vehicle, driver door is closed, and move away from vehicle is attempted

Reason for warning: Vehicle theft prevention, "engine cannot be restarted" prevention, battery depletion prevention
Warning start condition: Shift lever position is P, ignition switch is on (ACC or IG), opened driver side door is closed and key is not in detected in vehicle interior
Warning stop condition: Ignition switch on (ACC) or off, or key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
(when key is not detected continuously, sounds again when vehicle is first driven)
Combination meter display Telltale Illuminates
Wireless buzzer Sounds 3 times (short beeps)
Recommended user action Turn ignition switch off and exit vehicle while holding key


ii.

With shift lever on P and either ignition switch on (ACC) or steering lock / unlock set, driver door is opened, move away from vehicle is performed, and door handle lock switch is pressed in an attempt to perform entry lock operation

Reason for warning: Vehicle theft prevention, battery depletion prevention
Precondition: Change door control lock switch from off to on
Warning start condition: Shift lever position is P, ignition switch is on (ACC or IG), all doors closed, vehicle speed is 0 km/h (0 mph), key is not in detected in vehicle interior and key is detected in vehicle exterior
Warning stop condition: One of following conditions is met
1.

Ignition switch on (ACC) or off

2.

Key is detected in vehicle interior

3.

Shift lever position is not P

4.

Vehicle speed is above 0 km/h (0 mph)


Warning description Combination meter buzzer Short sound buzzer None
Combination meter display Telltale None
Situation C, pattern 1 illumination continues Illumination ends when situation C, pattern 1 warning stop conditions are met
Wireless buzzer Sounds for 60 seconds (long beep)
Recommended user action Turn ignition switch off and perform entry lock operation



e.

Situation D:

Entry door ajar warning

i.

With one of vehicle's doors open, entry lock operation is attempted

Reason for warning: Vehicle theft prevention
Precondition: Ignition switch on (ACC) or off, and one of doors open
Warning start condition: After preconditions are met, entry lock operation is performed
Warning stop condition: Ignition switch is on (ACC or IG), all doors are closed, wireless unlock is performed or 5 seconds have passed after warning start
Warning description Combination meter buzzer Short sound buzzer None
Combination meter display Telltale None
Wireless buzzer Sounds continuously (beep)
Recommended user action Close all doors and perform entry lock operation



f.

Situation E:

Passenger has brought key out of vehicle warning

i.

With engine switch in position other than off, key is brought out of vehicle by passenger

Reason for warning: "Engine cannot be started" prevention
Warning start condition: Ignition switch is on (ACC or IG), opened door other than driver side door is closed, vehicle speed is 0 km/h (0 mph) and key is not in detected in vehicle interior
Warning stop condition: Ignition switch on (ACC) or off, or key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
(when key is not detected continuously, sounds again when vehicle is first driven)
Combination meter display Telltale Illuminates
Wireless buzzer Sounds 3 times (short beeps)
Recommended user action Check if the passenger who exited the vehicle has the key or not



g.

Situation F:

Key is not within detection area warning

i.

With key not in vehicle cabin or key battery depleted, engine start is attempted or ignition switch on (ACC or IG) operation is attempted

Reason for warning: User confusion prevention
Warning condition: Ignition switch is not off and key is not detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
Combination meter display Telltale Illuminates for 8 seconds or less
Wireless buzzer None
Recommended user action Check if the key is within the detection area of the vehicle cabin.
If key is within the vehicle interior, built-in battery may be depleted
If key's wireless door lock switch is pressed, check if key's indicator illuminates
If indicator does not illuminate, replace the built-in battery
It is recommended that battery be bought at dealer, but battery can be replaced according to user preference



h.

Situation G:

Key lock-in prevention buzzer

i.

With key in vehicle cabin, vehicle is exited and door handle lock switch is pressed in an attempt to perform entry lock operation

Reason for warning: Key reminder vehicle theft warning prevention
Warning condition: Ignition switch on (ACC) or off, all doors closed, door handle lock switch ON and key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer None
Combination meter display Telltale None
Wireless buzzer Sounds for 2 seconds (long beep)
Recommended user action Pick up key that is in vehicle interior and perform entry lock operation again



i.

Situation H:

Key battery low warning

i.

Key with almost depleted battery is used to drive vehicle

Reason for warning: Helpful function
Warning condition: After ignition switch not off condition continues for 20 minutes or more, ignition switch is changed from not off to off position, key battery is low and key is detected in vehicle interior
Warning description Combination meter buzzer Short sound buzzer Sounds once (short beep)
Combination meter display Telltale None
Wireless buzzer None
Recommended user action Replace key's built-in battery with new one
It is recommended that battery be bought at dealer, but battery can be replaced according to user preference




BATTERY SAVING


HINT:

Leaving the electrical key close to electrical appliances that emit radio waves could cause the key to accidentally respond, which could cause the key battery to become quickly depleted.


a.

Vehicle battery saving function:

In the smart entry and start system, signals are emitted outside of the vehicle at a prescribed interval (0.25 seconds) when the doors are locked. Therefore, the vehicle battery could be drained if the vehicle remains parked for a long time. For this reason, the controls listed below are affected.

Condition Control
Both conditions below are met for 5 days:
·

Key is not in detection area

·

Touch sensor or lock switch operation is not performed


Signal transmission interval time is extended
Both conditions below are met for 14 days:
·

Key is not in detection area

·

Touch sensor or lock switch operation is not performed


Automatically deactivates the smart entry and start system

Reinstatement conditions

·

A wireless door lock control signal (lock, unlock, or back door open) is input and the ID code matches.

·

A user carries the electrical key and pushes a lock switch on an outside door handle.

·

A door is locked or unlocked by the mechanical key.



b.

Key battery and vehicle battery saving function:

In the smart entry and start system, if the electrical key is constantly located within the vehicle exterior detection area of the doors, the system maintains periodic communication with the electrical key. Therefore, if the vehicle remains parked in that state for a long time, the electrical key battery and the vehicle battery could be drained. For this reason, if this state continues longer than 10 minutes, the smart entry and start system automatically becomes deactivated.

Reinstatement conditions:

·

A wireless door lock control signal (lock or unlock) is input and the ID code matches.

·

A user carries the key and pushes a lock switch on an outside handle.

·

A door is locked or unlocked by the mechanical key.