When an ID code from the door electrical key oscillator LH matches the ID code from the key, the certification ECU outputs an SEL signal (Lo when output) to the door electrical key oscillator LH, activates the touch sensor located on the backside of the outside door handle, and enters unlock standby mode. When the touch sensor is touched, the door electrical key oscillator LH sends a SENS signal (Lo when output) to the certification ECU and the certification ECU sends an unlock signal to the driver side door lock.
Check the driver door entry lock and unlock function operation.
| Condition | Proceed to |
|---|---|
| Driver door entry lock function operates normally | A |
| Driver door entry lock and unlock functions do not operate | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the tester ON.
By following the tester screen display, check whether any DTCs are output.
| Result | Proceed to |
|---|---|
| DTC output (for 2AZ-FE) | A |
| DTC output (for 2GR-FE) | B |
| No DTC output | C |
C
A
(See pageEngine / Hybrid System>2AZ-FE STARTING>SMART ENTRY AND START SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
B
(See pageEngine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Check that all the doors unlock when the door control switch (for manual operation) is turned to UNLOCK.
All doors can be unlocked with door control switch.
OK
NG
Check that the wireless door lock and unlock functions operate normally.
Wireless door lock and unlock functions operate normally.
OK
NG
Check the Data List to confirm the operation of the door courtesy light switch (for driver side).
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D Door Courtesy SW | Driver side door courtesy light switch signal ON / OFF | ON: Driver side door is open
OFF: Driver side door is closed |
- |
On tester screen, item changes between ON and OFF according to above chart.
OK
NG
Check the Data List for proper functioning of the door lock position switch (for driver side).
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D-Door Lock Pos SW | Driver side door lock position switch signal / ON or OFF | ON: Driver side door is unlocked
OFF: Driver side door is locked |
- |
On tester screen, item changes between ON and OFF according to above chart.
OK
NG
Select the Active Test, use the intelligent tester to generate a control command, and then check that the door electrical key oscillator operates.
| Item | Test Details | Diagnostic Note |
|---|---|---|
| D-Seat Select | Driver side select ON / OFF | - |
ON (D-Seat Select is ON) appears on screen.
OK
NG
With "D-Seat Select" ON, check the Data List to confirm the operation of the touch sensor.
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
|---|---|---|---|
| D-Door Touch Sensor | Driver side door touch sensor / ON or OFF | ON: Sensor is touched
OFF: Sensor is not touched |
- |
When driver side door touch sensor is set to ON, ON (sensor is touched) appears on screen.
OK
NG
Temporarily replace the main body ECU with a new or normally functioning one.
Check that the entry unlock function operates normally (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>OPERATION CHECK).
Entry unlock function operates normally.
OK
NG
Measure the voltage of the oscillator.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (SEL) - Body ground | During Active Test | Below 1 V |
| 6 (SENS) - Body ground | Touch sensor is touched during Active Test | Below 1 V |
| Touch sensor is not touched during Active Test | 10 to 14 V |
NG
OK
Disconnect the G29 ECU connector.
Disconnect the h2 oscillator connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G29-5 (SEL1) - h2-4 (SEL) | Below 1 Ω |
| G29-22 (SEN1) - h2-6 (SENS) | |
| G29-33 (CLG1) - h2-10 (CLG) | |
| G29-34 (CG1B) - h2-5 (CLGB) | |
| G29-5 (SEL1) or h2-4 (SEL) - Body ground | 10 kΩ or higher |
| G29-22 (SEN1) or h2-6 (SENS) - Body ground | |
| G29-33 (CLG1) or h2-10 (CLG) - Body ground | |
| G29-34 (CG1B) or h2-5 (CLGB) - Body ground |
OK
NG
Disconnect the h2 oscillator connector.
Disconnect the h1 antenna connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| h2-2 (SGT) - h1-6 (SGT2) | Below 1 Ω |
| h2-3 (ANT1) - h1-5 (ANT1) | |
| h2-8 (ANT2) - h1-2 (ANT2) | |
| h2-9 (TRG-) - h1-1 (TRG-) | |
| h2-2 (SGT) or h1-6 (SGT2) - Body ground | 10 kΩ or higher |
| h2-3 (ANT1) or h1-5 (ANT1) - Body ground | |
| h2-8 (ANT2) or h1-2 (ANT2) - Body ground | |
| h2-9 (TRG-) or h1-1 (TRG-) - Body ground |
OK
NG
Temporarily replace the front door outside handle (electrical key antenna) with a new or normally functioning one.
Check that the entry unlock function operates normally (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>OPERATION CHECK).
Entry unlock function operates normally.
NG
OK