Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM J

DOOR LOCK  SMART ENTRY AND START SYSTEM  Driver Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

Neither the entry lock nor unlock functions operate when: 1) nothing is output from the door electrical key oscillator (for driver side), 2) the smart entry and start system is disabled through customization, or 3) the entire power door lock control system is malfunctioning.

WIRING DIAGRAM

B144908E14
6.219,0.646 6.594,0.823 0.375,0.177 10 false CLG1 6.219,1.427 6.615,1.604 0.396,0.177 10 false CG1B 6.219,2.24 6.594,2.417 0.375,0.177 10 false SEN1 6.219,3.01 6.573,3.188 0.354,0.177 10 false SEL1 0.469,0.625 0.844,0.802 0.375,0.177 10 false ANT2 0.469,1.448 0.844,1.625 0.375,0.177 10 false ANT1 0.458,2.25 0.917,2.427 0.458,0.177 10 false SGT2 0.479,3.031 0.833,3.208 0.354,0.177 10 false TRG- 2.802,0.646 3.104,0.823 0.302,0.177 10 false CLG 0.958,0.771 1.135,0.948 0.177,0.177 10 false 2 1.906,0.771 2.083,0.948 0.177,0.177 10 false 8 1.906,1.542 2.083,1.719 0.177,0.177 10 false 3 0.979,6.51 1.156,6.688 0.177,0.177 10 false 3 5.958,4.969 6.135,5.146 0.177,0.177 10 false 3 1.906,2.365 2.083,2.542 0.177,0.177 10 false 2 1.906,3.135 2.083,3.313 0.177,0.177 10 false 9 3.198,0.76 3.5,0.938 0.302,0.177 10 false 10 5.896,0.76 6.198,0.938 0.302,0.177 10 false 33 5.896,1.542 6.198,1.719 0.302,0.177 10 false 34 5.896,2.354 6.198,2.531 0.302,0.177 10 false 22 0.958,1.542 1.135,1.719 0.177,0.177 10 false 5 3.198,1.531 3.375,1.708 0.177,0.177 10 false 5 5.917,3.146 6.094,3.323 0.177,0.177 10 false 5 0.958,2.354 1.135,2.531 0.177,0.177 10 false 6 3.208,2.344 3.385,2.521 0.177,0.177 10 false 6 3.208,3.135 3.385,3.313 0.177,0.177 10 false 4 0.958,3.135 1.135,3.313 0.177,0.177 10 false 1 3.198,4.177 3.375,4.354 0.177,0.177 10 false 1 3.198,5.167 3.375,5.344 0.177,0.177 10 false 7 2.719,1.438 3.115,1.615 0.396,0.177 10 false CLGB 2.708,2.24 3.104,2.417 0.396,0.177 10 false SENS 2.823,3.031 3.104,3.208 0.281,0.177 10 false SEL 2.146,0.646 2.521,0.823 0.375,0.177 10 false ANT2 2.146,1.427 2.521,1.604 0.375,0.177 10 false ANT1 2.146,2.229 2.448,2.406 0.302,0.177 10 false SGT 2.146,3.021 2.5,3.198 0.354,0.177 10 false TRG- 2.896,4.042 3.083,4.219 0.188,0.177 10 false +B 2.792,5.021 3.115,5.198 0.323,0.177 10 false GND 6.229,4.844 6.677,5.021 0.448,0.177 10 false TSW1 0.469,6.375 0.865,6.552 0.396,0.177 10 false TRG+ 0.063,6.823 2.49,7.365 2.427,0.542 10 false h1 1.667,5.771 4.573,6.167 2.906,0.396 10 false h2 5.927,6.365 7.104,6.75 1.177,0.385 10 false G29 4.094,3.969 4.615,4.333 0.521,0.365 10 false from Battery 1.667,5.938 4.573,6.333 2.906,0.396 10 false Door Electrical Key Oscillator (for Driver Side) 5.927,6.531 7.104,6.917 1.177,0.385 10 false Certification ECU 0.063,6.979 2.448,7.5 2.385,0.521 10 false Door Electrical Key Antenna (for Driver Side Door Outside Handle)

PROCEDURE

1.TROUBLE AREA CONFIRMATION
a.

Check the driver door entry lock and unlock function operation.

Condition Proceed to
Driver door entry unlock function operates normally A
Driver door entry lock function operates normally B
Driver door entry lock and unlock functions do not operate C



C

2.CHECK FOR DTC

A

REFER TO " Driver door entry unlock function does not operate " FLOWCHART

B

REFER TO " Driver door entry lock function does not operate " FLOWCHART

2.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

By following the tester screen display, check whether any DTCs are output.

Result:
Result Proceed to
DTC output (for 2AZ-FE) A
DTC output (for 2GR-FE) B
No DTC output C




C

3.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION

A

B

3.CHECK MANUAL DOOR LOCK AND UNLOCK OPERATION
a.

Check that all the doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.

OK:

All doors can be locked and unlocked with door control switch.




OK

4.CHECK WIRELESS DOOR LOCK CONTROL OPERATION

NG

4.CHECK WIRELESS DOOR LOCK CONTROL OPERATION
a.

Check that the wireless door lock and unlock functions operate normally.

OK:

Wireless door lock and unlock functions operate normally.




OK

5.OPERATION CHECK (TRANSMITTER LED)

NG

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (w/ SMART ENTRY AND START SYSTEM)

5.OPERATION CHECK (TRANSMITTER LED)
a.

Using the wireless operation, unlock the doors. Wait approximately 3 seconds and bring the key within 70 to 100 cm of the driver door outside handle. Check the key's LED.

Result
LED Condition Proceed to
Not Blinking A
Blinking B



A

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR)

B

PERFORM WAVE ENVIRONMENT CHECK (CHANGE VEHICLE LOCATION AND CHECK AGAIN)

6.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DOOR ELECTRICAL KEY OSCILLATOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.

Certification ECU:
Item Test Details Diagnostic Note
D-Seat Outside Transmitter Driver side door electrical key oscillator ON / OFF -

OK:

When key is brought close to door oscillator that is ON, indicator light on key illuminates.




OK

7.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)

NG

REPLACE CERTIFICATION ECU

7.CHECK WIRE HARNESS (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)
B460031E03
0.083,0.417 0.5,0.667 0.417,0.25 0.25,3.667 0.667,3.917 0.417,0.25 2.063,1.781 2.188,1.427 true 2.594,1.771 2.302,1.427 true 1.958,3.646 2.531,3.646 true 2.438,4.135 1.958,3.781 true 0.094,0.042 1.677,0.313 1.583,0.271 10 false Wire Harness Side: 0.156,0.448 0.635,0.729 0.479,0.281 10 false G29 1.198,0.49 2.781,0.76 1.583,0.271 10 false Certification ECU 1.688,1.771 2.146,2.052 0.458,0.281 10 false CLG1 2.615,1.75 3.073,2.031 0.458,0.281 10 false CG1B 0.823,2.521 2.646,2.948 1.823,0.427 10 false Door Electrical Key Oscillator (for Driver Side) 2.594,3.573 3.052,3.854 0.458,0.281 10 false CLGB 2.5,4.104 2.958,4.385 0.458,0.281 10 false CLG 0.365,3.698 0.823,3.979 0.458,0.281 10 false h2

a.

Disconnect the G29 ECU connector.


b.

Disconnect the h2 oscillator connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G29-33 (CLG1) - h2-10 (CLG) Below 1 Ω
G29-34 (CG1B) - h2-5 (CLGB)
G29-33 (CLG1) or h2-10 (CLG) - Body ground 10 kΩ or higher
G29-34 (CG1B) or h2-5 (CLGB) - Body ground




OK

8.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - DOOR ELECTRICAL KEY ANTENNA)
B460030E01
0.5,1.25 0.833,1.5 0.333,0.25 0.5,3.5 0.833,3.75 0.333,0.25 1.719,1.24 2.396,0.833 true 1.563,1.229 1.021,0.927 true 1.292,1.844 1.708,1.396 true 2.313,1.854 1.854,1.396 true 1.854,3.438 2.448,3.438 true 1.875,3.781 2.51,4.219 true 1.031,4.302 1.635,3.802 true 1.021,3.063 1.615,3.458 true 0.083,0.073 1.49,0.333 1.406,0.26 10 false Wire Harness Side: 0.469,0.406 3.427,0.729 2.958,0.323 10 false Door Electrical Key Oscillator (for Driver Side) 2.448,0.74 2.906,0.99 0.458,0.25 10 false ANT1 0.979,1.854 1.438,2.104 0.458,0.25 10 false ANT2 0.688,0.813 1.146,1.063 0.458,0.25 10 false SGT 2.344,1.833 2.802,2.083 0.458,0.25 10 false TRG- 0.583,1.292 1.042,1.542 0.458,0.25 10 false h2 0.594,3.531 1.052,3.781 0.458,0.25 10 false h1 0.479,2.448 3.313,2.865 2.833,0.417 10 false Door Electrical Key Antenna (for Driver Side) 0.656,2.969 1.115,3.219 0.458,0.25 10 false TRG- 2.51,3.344 2.969,3.594 0.458,0.25 10 false ANT2 0.667,4.25 1.125,4.5 0.458,0.25 10 false ANT1 2.563,4.188 3.021,4.438 0.458,0.25 10 false SGT2

a.

Disconnect the h2 oscillator connector.


b.

Disconnect the h1 antenna connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
h2-2 (SGT) - h1-6 (SGT2) Below 1 Ω
h2-3 (ANT1) - h1-5 (ANT1)
h2-8 (ANT2) - h1-2 (ANT2)
h2-9 (TRG-) - h1-1 (TRG-)
h2-2 (SGT) or h1-6 (SGT2) - Body ground 10 kΩ or higher
h2-3 (ANT1) or h1-5 (ANT1) - Body ground
h2-8 (ANT2) or h1-2 (ANT2) - Body ground
h2-9 (TRG-) or h1-1 (TRG-) - Body ground




OK

9.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)
U188595E02
1.385,1.885 1.115,1.51 false 1.521,2.042 1.396,2.521 false 0.073,0.021 1.49,0.229 1.417,0.208 10 false Wire Harness Side: 0.875,1.375 1.177,1.594 0.302,0.219 10 false +B 1,2.458 1.469,2.667 0.469,0.208 10 false GND 0.396,1.802 0.625,2.052 0.229,0.25 10 false h2

a.

Disconnect the h2 oscillator connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
h2-7 (GND) - Body ground Below 1 Ω



c.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
h2-1 (+B) - Body ground 10 to 14 V




OK

10.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK WIRE HARNESS (DOOR ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
B460033E01
0.5,1.667 0.917,1.917 0.417,0.25 0.083,3.167 0.5,3.417 0.417,0.25 0.979,1.25 1.563,1.75 true 0.417,4.333 0.625,3.885 true 0.094,0.063 1.531,0.313 1.438,0.25 10 false Wire Harness Side: 0.792,0.438 2.531,0.917 1.74,0.479 10 false Door Electrical Key Antenna (for Driver Side) 0.563,1.135 1.073,1.396 0.51,0.26 10 false TRG+ 0.625,1.698 1.135,1.958 0.51,0.26 10 false h1 0.146,3.208 0.656,3.469 0.51,0.26 10 false G29 1.188,3.156 2.49,3.458 1.302,0.302 10 false Certification ECU 0.146,4.333 0.656,4.594 0.51,0.26 10 false TSW1

a.

Disconnect the h1 antenna connector.


b.

Disconnect the G29 ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
h1-3 (TRG+) - G29-3 (TSW1) Below 1 Ω
h1-3 (TRG+) or G29-3 (TSW1) - Body ground 10 kΩ or higher




OK

11.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
a.

Temporarily replace the front door outside handle (electrical key antenna) with a new or normally functioning one.


b.

Check that the entry lock and unlock functions operate normally (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>OPERATION CHECK).

OK:

Entry lock and unlock functions operate normally.




NG

12.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)

OK

END (ELECTRICAL KEY ANTENNA IS DEFECTIVE)

12.CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
a.

Temporarily replace the door electrical key oscillator (driver side) with a new or normally functioning one.


b.

Check that the entry lock and unlock functions operate normally.

OK:

Entry lock and unlock functions operate normally.




NG

13.CHECK MAIN BODY ECU (OPERATION)

OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

13.CHECK MAIN BODY ECU (OPERATION)
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check that the entry lock and unlock function operates normally (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>OPERATION CHECK).

OK:

Entry lock and unlock functions operate normally.




OK

END (MAIN BODY ECU IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU