Home › Vehicle Interior › DOOR LOCK › SMART ENTRY AND START SYSTEM
RM24M0E _58 Vehicle Interior _059568 DOOR LOCK _0292017 SMART ENTRY AND START SYSTEM J

DOOR LOCK  SMART ENTRY AND START SYSTEM  Back Door Entry Unlock Function does not Operate  


DESCRIPTION

When the back door opener switch is turned ON, the certification ECU uses the back door electrical key antenna (outer) and antenna to output a request signal to the outside of the vehicle for a distance of approximately 1.0 m (3.3 ft.) from the back door. A key near the back door detects this request and transmits its ID code. The door control receiver receives the ID code and sends this ID code to the certification ECU. The certification ECU checks if the ID code is valid. When the ID code is valid, the certification ECU sends a back door open signal to the main body ECU using the multiplex communication line and stops outputting request signals. The power back door ECU then unlocks the back door.

WIRING DIAGRAM

B115382E07
0.229,4.896 2.833,5.302 2.604,0.406 10 false M1 1.844,2.156 2.01,2.385 0.167,0.229 10 false 1 1.844,3.25 2.01,3.479 0.167,0.229 10 false 2 5.313,2.156 5.5,2.344 0.188,0.188 10 false 31 5.313,3.271 5.5,3.458 0.188,0.188 10 false 32 5.625,3.406 6.083,3.563 0.458,0.156 10 false CG8B 1.313,3.396 1.771,3.552 0.458,0.156 10 false CLGB 5.615,2.271 6.083,2.438 0.469,0.167 10 false CLG8 1.292,2.271 1.76,2.438 0.469,0.167 10 false CLG5 5.49,4.958 6.656,5.292 1.167,0.333 10 false G29 0.24,5.063 2.844,5.469 2.604,0.406 10 false Back Door Electrical Key Antenna (Outer) 5.49,5.135 6.656,5.469 1.167,0.333 10 false Certification ECU

PROCEDURE

1.CHECK FOR DTC
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

By following the tester screen display, check whether any DTCs are output.

Result:
Result Proceed to
DTC output (for 2AZ-FE) A
DTC output (for 2GR-FE) B
No DTC output C




C

2.CHECK MANUAL BACK DOOR OPENER OPERATION

A

B

2.CHECK MANUAL BACK DOOR OPENER OPERATION
a.

Check that the manual back door opener function operates normally.

OK:

Manual back door opener function operates normally.




OK

3.CHECK WIRELESS BACK DOOR OPENER OPERATION

NG

3.CHECK WIRELESS BACK DOOR OPENER OPERATION
a.

Check that the wireless back door opener function operates normally.

OK:

Wireless back door opener function operates normally.




OK

4.CHECK OPERATION OF KEY

NG

4.CHECK OPERATION OF KEY
a.

After replacing the key with a normally functioning one, check that the wireless back door opener function operates normally.

OK:

Wireless back door opener function operates normally.




NG

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR ELECTRICAL KEY ANTENNA [for Outer])

OK

END (KEY IS DEFECTIVE)

5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BACK DOOR ELECTRICAL KEY ANTENNA [for Outer])
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the antenna (for outer) operates.

Certification ECU:
Item Test Details Diagnostic Note
Outside Trunk/Backdoor Transmitter Back door electrical key antenna (for outer) ON / OFF -

OK:

When key is brought close to back door, antenna (for outer) is turned OFF and indicator on key illuminates.




OK

6.READ VALUE USING INTELLIGENT TESTER (BACK DOOR UNLOCK SWITCH)

NG

8.CHECK WIRE HARNESS (CERTIFICATION ECU - BACK DOOR ELECTRICAL KEY ANTENNA [for Outer])
6.READ VALUE USING INTELLIGENT TESTER (BACK DOOR UNLOCK SWITCH)
a.

Check the Data List for proper functioning of the back door unlock switch.

Certification ECU:
Item Measurement Item / Range (Display) Normal Condition Diagnostic Note
Tr/B-Door Unlock SW Back door unlock switch / ON or OFF ON: Back door unlock switch is pushed
OFF: Back door unlock switch is not pushed
-

OK:

ON (back door unlock switch is pushed) appears on the screen.




OK

7.CHECK OPERATION OF POWER BACK DOOR ECU

NG

7.CHECK OPERATION OF POWER BACK DOOR ECU
a.

After replacing the power back door ECU with a normal one, check that the back door entry unlock functions operates normally.

OK:

Back door entry unlock function operates normally.




OK

END (POWER BACK DOOR ECU IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU

8.CHECK WIRE HARNESS (CERTIFICATION ECU - BACK DOOR ELECTRICAL KEY ANTENNA [for Outer])
B460032E01
1.5,0.583 1.917,0.833 0.417,0.25 1.5,2.667 1.917,2.917 0.417,0.25 1.49,1.781 1.927,1.438 false 2.594,1.792 2.052,1.438 false 1.25,3.719 1.594,3.563 false 2.219,3.781 1.813,3.552 false 0.073,0.042 1.708,0.271 1.635,0.229 10 false Wire Harness Side: 1.219,0.302 2.406,0.646 1.188,0.344 10 false Certification ECU 1.573,0.625 2.208,0.917 0.635,0.292 10 false G29 1.177,1.792 1.813,2.083 0.635,0.292 10 false CLG8 2.479,1.813 2.948,2.063 0.469,0.25 10 false CG8B 0.344,2.281 3.177,2.594 2.833,0.313 10 false Back Door Electrical Key Antenna (for Outer) 1.594,2.698 2.229,2.99 0.635,0.292 10 false M1 2.271,3.708 2.906,4 0.635,0.292 10 false CLG5 0.823,3.667 1.458,3.958 0.635,0.292 10 false CLGB

a.

Disconnect the G29 ECU connector.


b.

Disconnect the M1 antenna connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G29-31 (CLG8) - M1-1 (CLG5) Below 1 Ω
G29-32 (CG8B) - M1-2 (CLGB) Below 1 Ω
G29-31 (CLG8) or M1-1 (CLG5) - Body ground 10 kΩ or higher
G29-32 (CG8B) or M1-2 (CLGB) - Body ground 10 kΩ or higher




OK

9.CHECK BACK DOOR ELECTRICAL KEY ANTENNA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK BACK DOOR ELECTRICAL KEY ANTENNA
a.

After replacing the back door electrical key antenna with a normal one, check that the back door entry unlock functions operates normally.

OK:

Back door entry unlock function operates normally.




NG

10.CHECK MAIN BODY ECU (OPERATION)

OK

END (BACK DOOR ELECTRICAL KEY ANTENNA IS DEFECTIVE)

10.CHECK MAIN BODY ECU (OPERATION)
a.

Temporarily replace the main body ECU with a new or normally functioning one.


b.

Check that the back door entry unlock function operates normally.

OK:

Back door entry unlock function operates normally.




OK

END (MAIN BODY ECU IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU