Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM U

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  TERMINALS OF ECM  


ECM


U189482E02
2.354,0.26 2.729,0.49 0.375,0.229 10 false D2 5.583,0.271 5.792,0.427 0.208,0.156 10 false A7

HINT:

The standard voltage and resistance of each ECM terminal is shown in the table below.

In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage or resistance between the terminals is shown under "Specified Condition".

Use the illustration above as a reference for the ECM terminals.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A7-1 (+B2) - D2-104 (E1) B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A7-2 (+B) - D2-104 (E1) B - BR Power source of ECM Engine switch on (IG) 11 to 14 V
A7-3 (+BM) - D2-104 (E1) R - BR Power source of throttle actuator Always 11 to 14 V
A7-20 (BATT) - D2-104 (E1) W - BR Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
A7-41 (CANH) - D2-104 (E1) B - BR CAN communication line Engine switch on (IG) Pulse generation
(See waveform 1)
A7-49 (CANL) - D2-104 (E1) W - BR CAN communication line Engine switch on (IG) Pulse generation
(See waveform 2)
A7-36 (STP) - D2-104 (E1) L - BR Stop light switch signal Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V
A7-48 (STA) - D2-104 (E1) B - BR Starter signal Cranking 5.5 V or higher
A7-44 (MREL) - D2-104 (E1) Y - BR EFI MAIN relay Engine switch on (IG) 11 to 14 V
A7-16 (SFTU) - D2-104 (E1) P - BR Up-shift position switch signal Engine switch on (IG) and shift lever in M 11 to 14 V
Engine switch on (IG) and shift lever in "+" (up-shift) Below 1 V
A7-51 (SFTD) - D2-104 (E1) GR - BR Down-shift position switch signal Engine switch on (IG) and shift lever in M 11 to 14 V
Engine switch on (IG) and shift lever in "-" (down-shift) Below 1 V
D2-52 (STAR) - D2-104 (E1) LG - BR Park/neutral position switch signal Engine switch on (IG) and shift lever in P or N Below 1 V
Engine switch on (IG) and shift lever not in P or N 11 to 14 V
D2-53 (R) - D2-104 (E1) R - BR R position switch signal Engine switch on (IG) and shift lever in R 11 to 14 V
Engine switch on (IG) and shift lever not in R Below 1 V
D2-54 (N) - D2-104 (E1) L - BR N position switch signal Engine switch on (IG) and shift lever in N 11 to 14 V
Engine switch on (IG) and shift lever not in N Below 1 V
D2-56 (D) - D2-104 (E1) W - BR D position switch signal Engine switch on (IG) and shift lever in D 11 to 14 V
Engine switch on (IG) and shift lever not in D Below 1 V
D2-73 (P) - D2-104 (E1) G - BR P position switch signal Engine switch on (IG) and shift lever in P 11 to 14 V
Engine switch on (IG) and shift lever not in P Below 1 V
D2-74 (S) - D2-104 (E1) G - BR S position switch signal Engine switch on (IG) and shift lever in M 11 to 14 V
Engine switch on (IG) and shift lever not in M Below 1 V
D2-76 (SLS+) - D2-75 (SLS-) BR - Y Shift solenoid valve SLS signal Engine idling Pulse generation
(See waveform 3)
D2-78 (DS2) - D2-104 (E1) R - BR Shift solenoid valve DS2 signal Accelerator pedal depressed further after driving at constant vehicle speed with shift lever in D Pulse generation
(See waveform 4)
D2-79 (DS1) - D2-104 (E1) W - BR Shift solenoid valve DS1 signal Accelerator pedal released while driving with shift lever in D Pulse generation
(See waveform 5)
D2-57 (SL) - D2-104 (E1) L - BR Shift solenoid valve SL signal Engine switch on (IG) and shift lever in N 11 to 14 V
D2-80 (DSU) - D2-104 (E1) W - BR Shift solenoid valve DSU signal Lock-up turned from off to on Pulse generation
(See waveform 6)
D2-72 (THO1) - D2-95 (ETHO) G - BR CVT fluid temperature sensor signal CVT fluid temperature: 60 to 120°C (140 to 248°F) 0.2 to 1.0 V
D2-71 (PTO) - D2-94 (EPTO) B - LG Oil pressure sensor signal Engine idling and shift lever in P 0.8 to 1.2 V
D2-70 (VCPT) - D2-94 (EPTO) W - LG Power supply for oil pressure sensor signal Engine switch on (IG) 4.5 to 5.5 V
D2-104 (E1) - Body ground BR - Body ground Ground Always Below 1 Ω
D2-101 (NIN+) - D2-102 (NIN-) G - R Transmission revolution sensor (NIN) signal When driving with shift lever in D, vehicle speed approx. 6 km/h (3.7 mph) and engine speed approx. 760 rpm Pulse generation
(See waveform 7)
D2-126 (NT+) - D2-103 (NT-) V - P Transmission revolution sensor (NT) signal When driving with shift lever in D, vehicle speed approx. 12 km/h (7.5 mph) and engine speed approx. 1040 rpm Pulse generation
(See waveform 8)
D2-125 (NOT+) - D2-124 (NOT-) B - W Transmission revolution sensor (NOUT) signal When driving with shift lever in D, vehicle speed approx. 12 km/h (7.5 mph) and engine speed approx. 1040 rpm Pulse generation
(See waveform 9)

a.
C201361E04
2.458,0.906 3.115,1.104 0.656,0.198 10 false 1 V/DIV. 2.563,2.031 2.979,2.229 0.417,0.198 10 false GND 1.469,2.604 2.427,2.792 0.958,0.188 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 1.

Reference
Terminal No. (Symbol) Tool Setting Condition
A7-41 (CANH) - D2-104 (E1) 1 V/DIV., 10 μsec./DIV. Engine switch on (IG)


b.
C201362E05
2.438,0.906 3.094,1.104 0.656,0.198 10 false 1 V/DIV. 2.563,2.042 2.979,2.24 0.417,0.198 10 false GND 1.479,2.594 2.438,2.781 0.958,0.188 10 false 10 μsec./DIV.

Using an oscilloscope, check waveform 2.

Reference
Terminal No. (Symbol) Tool Setting Condition
A7-49 (CANL) - D2-104 (E1) 1 V/DIV., 10 μsec./DIV. Engine switch on (IG)


c.
C201363E03
2.458,0.906 3.115,1.104 0.656,0.198 10 false 5 V/DIV. 1.469,2.594 2.427,2.781 0.958,0.188 10 false 1 msec./DIV. 2.563,1.635 2.969,1.833 0.406,0.198 10 false GND

Using an oscilloscope, check waveform 3.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-76 (SLS+) - D2-75 (SLS-) 5 V/DIV., 1 msec./DIV. Engine idling


d.
C201364E03
2.438,0.906 3.094,1.104 0.656,0.198 10 false 10 V/DIV. 1.5,2.604 2.458,2.792 0.958,0.188 10 false 5 msec./DIV. 2.563,1.635 2.969,1.833 0.406,0.198 10 false GND

Using an oscilloscope, check waveform 4.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-78 (DS2) - D2-104 (E1) 10 V/DIV., 5 msec./DIV. Accelerator pedal depressed further after driving at constant vehicle speed with shift lever in D

HINT:

Duty ratio increases as the gear ratio increases.



e.
C201365E03
2.448,0.896 3.104,1.094 0.656,0.198 10 false 10 V/DIV. 1.51,2.604 2.469,2.792 0.958,0.188 10 false 5 msec./DIV. 2.573,1.615 2.979,1.813 0.406,0.198 10 false GND

Using an oscilloscope, check waveform 5.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-79 (DS1) - D2-104 (E1) 10 V/DIV., 5 msec./DIV. Accelerator pedal released while driving with shift lever in D

HINT:

Duty ratio increases as the gear ratio decreases.



f.
C201366E04
2.438,0.917 3.094,1.115 0.656,0.198 10 false 10 V/DIV. 1.479,2.594 2.438,2.781 0.958,0.188 10 false 20 msec./DIV. 2.563,1.625 2.969,1.823 0.406,0.198 10 false GND

Using an oscilloscope, check waveform 6.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-80 (DSU) - D2-104 (E1) 10 V/DIV., 20 msec./DIV. Lock-up turned from off to on

HINT:

Duty ratio increases to 100% with lock-up on.



g.
C201367E03
2.448,0.927 3.104,1.125 0.656,0.198 10 false 1 V/DIV. 1.5,2.604 2.458,2.792 0.958,0.188 10 false 2 msec./DIV. 2.552,1.635 2.958,1.833 0.406,0.198 10 false GND

Using an oscilloscope, check waveform 7.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-101 (NIN+) - D2-102 (NIN-) 1 V/DIV., 2 msec./DIV. When driving with shift lever in D, vehicle speed approx. 6 km/h (3.7 mph) and engine speed approx. 760 rpm

HINT:

The wavelength shortens and the voltage increases as the primary pulley speed increases.



h.
C070235E02
2.823,1 3.281,1.198 0.458,0.198 10 true GND

Using an oscilloscope, check waveform 8.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-126 (NT+) - D2-103 (NT-) 1 V/DIV., 2 msec./DIV. When driving with shift lever in D, vehicle speed approx. 12 km/h (7.5 mph) and engine speed approx. 1040 rpm

HINT:

The wavelength shortens as the turbine speed increases.



i.
C070236E02
2.823,1.021 3.281,1.219 0.458,0.198 10 true GND

Using an oscilloscope, check waveform 9.

Reference
Terminal No. (Symbol) Tool Setting Condition
D2-125 (NOT+) - D2-124 (NOT-) 1 V/DIV., 2 msec./DIV. When driving with shift lever in D, vehicle speed approx. 12 km/h (7.5 mph) and engine speed approx. 1040 rpm

HINT:

The wavelength shortens as the secondary pulley speed increases.