Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to switch the shift range between "1" (M1 range) and "7" (M7 range) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C211629E14
5.792,3.854 6.177,4.052 0.385,0.198 10 false ECM 5.594,1.74 6.01,1.938 0.417,0.198 10 false SFTU 5.302,2.719 5.531,2.917 0.229,0.198 10 false 74 5.281,1.531 5.479,1.729 0.198,0.198 10 false 16 5.594,2.917 6.083,3.115 0.49,0.198 10 false S 3.625,1.625 4.115,1.823 0.49,0.198 10 false SFTU 4.063,3.042 4.292,3.24 0.229,0.198 10 false 13 4.083,1.854 4.281,2.052 0.198,0.198 10 false 5 3.875,2.802 4.083,3 0.208,0.198 10 false S 2.469,3.406 2.781,3.604 0.313,0.198 10 false G9 2.469,3.583 4.323,3.781 1.854,0.198 10 false Transmission Control Switch 5.594,2.323 6.01,2.521 0.417,0.198 10 false SFTD 5.292,2.125 5.49,2.323 0.198,0.198 10 false 51 3.625,2.219 4.115,2.417 0.49,0.198 10 false SFTD 4.083,2.448 4.281,2.646 0.198,0.198 10 false 4 2.74,1.625 3.031,1.823 0.292,0.198 10 false E 2.479,1.854 2.677,2.052 0.198,0.198 10 false 11 2.729,2.792 2.958,2.99 0.229,0.198 10 false IG 2.531,3.042 2.729,3.24 0.198,0.198 10 false 6 0.729,2.917 1.948,3.115 1.219,0.198 10 false from ECU-IG Fuse 5.292,1.75 5.594,1.948 0.302,0.198 10 false A7 5.292,2.333 5.594,2.531 0.302,0.198 10 false A7 5.292,2.917 5.594,3.115 0.302,0.198 10 false D2

PROCEDURE

1.INSPECT TRANSMISSION CONTROL SWITCH
a.
C199170E41
1.573,0.948 0.865,0.438 true 1.438,0.948 0.865,0.677 true 0.865,1.49 1.438,1.208 true 1.708,0.948 2.531,0.438 true 2.552,1.708 1.729,1.198 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *1 0.49,0.333 0.917,0.531 0.427,0.198 10 false SFTU 0.698,0.573 0.969,0.771 0.271,0.198 10 false IG 0.729,1.427 1.042,1.625 0.313,0.198 10 false S 2.573,0.333 3,0.531 0.427,0.198 10 false SFTD 2.604,1.625 3.031,1.823 0.427,0.198 10 false E

Disconnect the transmission control switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (IG) - 13 (S) Shift lever in M, "+" or "-" Below 1 Ω
5 (SFTU) - 11 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
4 (SFTD) - 11 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
6 (IG) - 13 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
5 (SFTU) - 11 (E) Shift lever in M 10 kΩ or higher
4 (SFTD) - 11 (E) Shift lever in M 10 kΩ or higher


Text in Illustration
*1 Component without harness connected
(Transmission Control Switch)


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD C



A

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY AND BODY GROUND)

B

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

C

REPLACE TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BATTERY AND BODY GROUND)
a.
U189487E02
2.042,1.063 2.615,0.552 false 2.615,1.833 1.729,1.323 false 0.063,0.052 0.375,0.25 0.313,0.198 10 false *1 2.646,0.385 2.958,0.583 0.313,0.198 10 false IG 0.448,0.99 0.823,1.219 0.375,0.229 10 false G9 2.656,1.781 2.969,1.979 0.313,0.198 10 false E

Disconnect the transmission control switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G9-6 (IG) - Body ground Engine switch on (IG) 11 to 14 V
G9-6 (IG) - Body ground Engine switch off Below 1 V



c.

Turn the engine switch off.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G9-11 (E) - Body ground Always Below 1 Ω



Text in Illustration
*1 Front view of wire harness connector
(to Transmission Control Switch)


OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the ECM connectors.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D2-74 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever in M, "+" or "-"


11 to 14 V
D2-74 (S) - Body ground
·

Engine switch on (IG)

·

Shift lever not in M, "+" or "-"


Below 1 V



d.

Turn the engine switch off.


e.

Disconnect the spiral cable sub-assembly connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
A7-51 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
A7-16 (SFTU) - Body ground Shift lever in M 10 kΩ or higher
A7-51 (SFTD) - Body ground Shift lever in M 10 kΩ or higher




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION