Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2013.04–2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM D

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


EURO-OBD (EUROPE)


FI02547

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in:

a.

The emission control system components


b.

The powertrain control components (which affect vehicle emissions)


c.

The computer

In addition, if the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain recorded in the ECM memory.

To check DTCs, connect the intelligent tester or OBD scan tool to the Data Link Connector3 (DLC3) of the vehicle.

The scan tool displays DTCs, the freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be erased the scan tool (See page Drivetrain>K112 (CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR).



NORMAL MODE AND CHECK MODE


The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2-trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available to technicians as an option. In check mode, 1-trip detection logic is used when reproducing malfunction symptoms for increasing the ability of the system to detect malfunctions, including intermittent malfunctions (intelligent tester only).


2-TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the engine switch is turned off and then turned on (IG) again, and the same malfunction is detected again, the MIL illuminates.



FREEZE FRAME DATA


a.

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not and whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837E70
0.344,1.729 2.729,1.896 2.385,0.167 10 false Freeze frame data which can be read 0.688,0.583 1.313,0.781 0.625,0.198 10 false 0.5 sec. 1.323,0.583 1.948,0.781 0.625,0.198 10 false 0.5 sec. 1.948,0.583 2.573,0.781 0.625,0.198 10 true 0.5 sec. 1.844,0.073 2.74,0.229 0.896,0.156 10 false DTC is stored

The intelligent tester displays freeze frame data recorded at five different points: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. The data can be used to reproduce the vehicle condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.



CHECK DATA LINK CONNECTOR 3 (DLC3)




CHECK BATTERY VOLTAGE


Standard voltage:

11 to 14 V


If the voltage is below 11 V, replace the battery.


CHECK MIL


a.

Check that the MIL illuminates when turning the engine switch on (IG).

If the MIL does not illuminate, there is a problem in the MIL circuit (See page Engine / Hybrid System>2AZ-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit).


b.

When the engine is started, the MIL goes off.