DATA LIST
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Neutral Position SW Signal | PNP switch status/
ON or OFF |
·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status/
ON or OFF |
·
ON: Brake pedal depressed ·
OFF: Brake pedal released |
- |
| SPD (NT) | Input turbine speed/
min.: 0 rpm max.: 12750 rpm |
·
Equal to engine speed: Lock-up on (After warming up engine) ·
Nearly equal to engine speed: Lock-up off (Engine idling with shift lever in P or N) ·
0 rpm: Vehicle stopped with shift lever in R |
Data is displayed in increments of 50 rpm. |
| Shift SW Status (P Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in N ·
OFF: Shift lever not in N |
|
| Sports Shift Up SW | Sport shift up switch status/
ON or OFF |
·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status/
ON or OFF |
·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held in "-" (down-shift) |
- |
| Sports Mode Selection SW | Sport mode select switch status/
ON or OFF |
·
ON: Shift lever in M, "+" or "-" ·
OFF: Shift lever not in M, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status/
ON or OFF |
·
ON: Shift lever in D ·
OFF: Shift lever not in D |
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
|
| A/T Oil Temperature 1 | CVT fluid temperature sensor value/
min.: -40°C (-40°F) max.: 215°C (419°F) |
·
After stall speed test: Approx. 80°C (176°F) ·
Equal to ambient temperature after cold soak |
If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted. |
| NT Sensor Voltage | Transmission revolution sensor (NT) output voltage/
min.: 0.000 V max.: 4.999 V |
0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| SPD (NIN) | Primary pulley speed (NIN)/
min.: 0 rpm max.: 12750 rpm |
·
Vehicle stopped: 0 rpm ·
Lock-up on (After warming up engine): Primary pulley speed (NIN) equal to engine speed |
Data is displayed in increments of 50 rpm. |
| SPD (NOUT) | Secondary pulley speed (NOUT)/
min.: 0 rpm max.: 12750 rpm |
·
0 rpm: Vehicle stopped ·
Approximately 2650 rpm: Vehicle being driven at approximately 60 km/h (37 mph) |
Data is displayed in increments of 50 rpm. |
| NOUT Sensor Voltage | Transmission revolution sensor (NOUT) output voltage/
min.: 0.000 V max.: 4.999 V |
0.1 to 1.9 V: Engine idling (Vehicle stopped with shift lever in P or N) | - |
| A/T Oil Pressure | Secondary oil pressure value/
min.: -0.625 MPa max.: 9.575 MPa |
Secondary oil pressure inspection
·
D position stall speed test: 4.0 to 5.0 MPa ·
R position stall speed test: 3.6 to 4.2 MPa |
- |
| G sensor | Converted output voltage of G sensor/
min.: 0 V max.: 5 V |
Displays converted voltage of G sensor
·
Vehicle on level ground: 2.31 V to 2.69 V ·
Decelerating: 1.88 V to 2.5 V ·
Accelerating: 2.5 V to 3.11 V ·
G sensor malfunction: Set to 1.87 V ·
Communication malfunction: Set to 1.87 V |
- |
| Solenoid (DSU) | Shift solenoid valve DSU status/
ON or OFF |
·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Lock Up | Lock-up/
ON or OFF |
·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Lock Up Solenoid Status | Shift solenoid valve SL status/
ON or OFF |
·
ON: Shift solenoid valve SL on ·
OFF: Shift solenoid valve SL off |
- |
| Shift Status*1 | ECM gearshift command/
1st, 2nd, 3rd, 4th or 5th |
Same as actual gear | - |
| Solenoid (DS2) | Shift solenoid valve DS2 status/
ON or OFF |
·
OFF: Constant cruising with shift lever in D ·
ON: Accelerator pedal depressed further after cruising with shift lever in D |
- |
| Solenoid (DS1) | Shift solenoid valve DS1 status/
ON or OFF |
·
ON: Driving with shift lever in D and accelerator pedal depressed ·
OFF: Accelerator pedal released when driving with shift lever in D with accelerator pedal depressed |
- |
| Solenoid (SLS) | Shift solenoid valve SLS status/
ON or OFF |
·
ON: After engine start ·
OFF: Engine switch on (IG) |
- |
| G Sensor Calibration | G sensor calibration status/
Incomplete or Complete |
Complete | - |
| AT Fluid | Lock-up judder judgment/
ON or OFF |
·
ON: Judder judgment occurs ·
OFF: Judder judgment does not occur |
- |
| G Sensor Learning Value | G sensor learned value voltage/
min.: 0 V max.: 5 V |
G sensor calibration is complete: 2.31 V to 2.69 V | - |
| CVT Oil Press Calibration | CVT oil pressure calibration status/
Incomplete or Complete |
Complete | - |
*1:"Shift Status" is a signal divides into 5 gear position for ACTIVE TEST.
It does not express gear ratio for normal driving and gear positions for 7-speed sport sequential shiftmatic mode.
ACTIVE TEST
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Turn on and off TC and TE1 connection | ON or OFF | ·
ON: TC and TE1 are connected. ·
OFF: TC and TE1 are disconnected. |
| Activate the Lock Up | Operate lock-up | ON or OFF | Possible to check lock-up operation.
[Vehicle Condition] Vehicle speed: 40 km/h (25 mph) or more |
| Activate the Solenoid (SL) | Operate shift solenoid valve SL | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Control the Shift Position | Operates the shift solenoid valves to allow the gear ratio to be manually selected [1st - 2nd - 3rd - 4th - 5th]
Reference gear ratios: 1st (2.4 gear ratio max.) - 2nd (1.5) - 3rd (1.0) - 4th (0.7) - 5th (0.43 gear ratio min.) |
·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Used to check the operation of the shift solenoid valves.
[Vehicle Condition] 50 km/h (30 mph) or less
|
| Activate the Solenoid (DSU) | Operate shift solenoid valve DSU | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (DS1) | Operate shift solenoid valve DS1 | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (DS2) | Operate shift solenoid valve DS2 | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Control the SLS Pressure | Operate shift solenoid valve SLS | High or Low | [Vehicle Condition]
·
Vehicle stopped ·
Engine idling |
| Activate the Solenoid (SLS) | Operate shift solenoid valve SLS | ON or OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |