Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0840  Transmission Fluid Pressure Sensor/Switch "A" Circuit  P0842  Transmission Fluid Pressure Sensor/Switch "A" Circuit Low  P0843  Transmission Fluid Pressure Sensor/Switch "A" Circuit High  


DESCRIPTION

The ECM performs learning control for the belt clamping pressure based on the belt clamping pressure signal, which is detected by the oil pressure sensor.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0840
1.

2 seconds or more have elapsed after the engine is started.

2.

There is an open or short circuit in the oil pressure sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Open or short in oil pressure sensor circuit

·

Oil pressure sensor

·

ECM


P0842
1.

2 seconds or more have elapsed after the engine is started.

2.

There is a short circuit in the oil pressure sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Short in oil pressure sensor circuit

·

Oil pressure sensor

·

ECM


P0843
1.

2 seconds or more have elapsed after the engine is started.

2.

There is an open circuit in the oil pressure sensor circuit.

3.

0.5 seconds

4.

1 trip detection logic


·

Open in oil pressure sensor circuit

·

Oil pressure sensor

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short circuit in the oil pressure sensor circuit. When there is an open or short circuit in the oil pressure sensor circuit, the ECM detects the problem, illuminates the MIL and stores the DTCs.

WIRING DIAGRAM

C200617E22
5.813,2.927 6.125,3.125 0.313,0.198 10 false D2 5.813,3.104 6.198,3.302 0.385,0.198 10 false ECM 5.615,1.24 6.073,1.438 0.458,0.198 10 false VCPT 5.333,2.333 5.615,2.531 0.281,0.198 10 false 94 5.323,1.365 5.625,1.563 0.302,0.198 10 false 70 5.625,2.208 6.115,2.406 0.49,0.198 10 false EPTO 2.396,1.24 2.75,1.438 0.354,0.198 10 false VC 2.75,2.333 2.979,2.531 0.229,0.198 10 false 1 2.75,1.365 2.948,1.563 0.198,0.198 10 false 3 2.427,2.219 2.677,2.417 0.25,0.198 10 false E2 1.365,2.677 1.677,2.875 0.313,0.198 10 false D66 1.354,2.875 2.688,3.073 1.333,0.198 10 false Oil Pressure Sensor 5.323,1.854 5.604,2.052 0.281,0.198 10 false 71 5.615,1.729 6.104,1.927 0.49,0.198 10 false PTO 2.75,1.854 2.979,2.052 0.229,0.198 10 false 2 2.313,1.729 2.688,1.927 0.375,0.198 10 false PTO

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (A/T OIL PRESSURE)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List.


f.

In accordance with the display on the tester, read the Data List.

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
A/T Oil Pressure Secondary oil pressure value/
min.: -0.625 MPa
max.: 9.575 MPa
Secondary oil pressure inspection
·

D position stall speed test: 4.0 to 5.0 MPa

·

R position stall speed test: 3.6 to 4.2 MPa


-

Result
Result Proceed to
Data displayed is not as specified under Normal Condition A
Data displayed is as specified under Normal Condition B



A

2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)

B

6.REPLACE ECM
2.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENSOR - ECM)
a.

Disconnect the oil pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D66-1 (E2) - D2-94 (EPTO) Always Below 1 Ω
D66-2 (PTO) - D2-71 (PTO) Always Below 1 Ω
D66-3 (VC) - D2-70 (VCPT) Always Below 1 Ω
D66-1 (E2) or D2-94 (EPTO) - Body ground Always 10 kΩ or higher
D66-2 (PTO) or D2-71 (PTO) - Body ground Always 10 kΩ or higher
D66-3 (VC) or D2-70 (VCPT) - Body ground Always 10 kΩ or higher




OK

3.INSPECT ECM (VCPT TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VCPT TERMINAL VOLTAGE)
a.
U189485E02
1.24,1.698 1.542,1.188 false 2.208,1.698 1.917,1.188 false 0.052,0 0.271,0.198 0.219,0.198 10 false *1 0.5,1.042 0.875,1.271 0.375,0.229 10 false D66 1.073,1.729 1.313,1.927 0.24,0.198 10 false E2 2.135,1.729 2.406,1.927 0.271,0.198 10 false VC

Disconnect the oil pressure sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
D66-1 (E2) - D66-3 (VC) Engine switch on (IG) 4.75 to 5.25 V


Text in Illustration
*1 Front view of wire harness connector
(to Oil Pressure Sensor)



OK

4.REPLACE OIL PRESSURE SENSOR

NG

6.REPLACE ECM
4.REPLACE OIL PRESSURE SENSOR

NEXT

5.PERFORM INITIALIZATION
6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION