Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2014.09
RM24M0E _52 Drivetrain _059572 K112 CVT _0292047 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P0962  Pressure Control Solenoid "A" Control Circuit Low (Shift Solenoid Valve DS1)  P0963  Pressure Control Solenoid "A" Control Circuit High (Shift Solenoid Valve DS1)  P0966  Pressure Control Solenoid "B" Control Circuit Low (Shift Solenoid Valve DS2)  P0967  Pressure Control Solenoid "B" Control Circuit High (Shift Solenoid Valve DS2)  


DESCRIPTION

Using the shift solenoid valve DS1 (inflow to the primary pulley) and shift solenoid valve DS2 (outflow from the primary pulley), the ECM controls the line pressure and fluid volume input to and output from the primary pulley according to the vehicle speed and accelerator pedal angle. As a fail-safe function, if a solenoid is shorted or open, the ECM stops current to the faulty solenoid.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0962
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is a short circuit in the shift solenoid valve DS1 circuit.

3.

20 times

4.

1 trip detection logic


·

Short in shift solenoid valve DS1 circuit

·

Continuously variable transaxle assembly

·

ECM


P0963
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is an open circuit in the shift solenoid valve DS1 circuit.

3.

20 times

4.

1 trip detection logic


·

Open in shift solenoid valve DS1 circuit

·

Continuously variable transaxle assembly

·

ECM


P0966
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is a short circuit in the shift solenoid valve DS2 circuit.

3.

20 times

4.

1 trip detection logic


·

Short in shift solenoid valve DS2 circuit

·

Continuously variable transaxle assembly

·

ECM


P0967
1.

The vehicle is driven so that gear ratio changes occur.

2.

There is an open circuit in the shift solenoid valve DS2 circuit.

3.

20 times

4.

1 trip detection logic


·

Open in shift solenoid valve DS2 circuit

·

Continuously variable transaxle assembly

·

ECM



MONITOR DESCRIPTION

These DTCs indicate an open or short circuit in the shift solenoid valve DS1 or DS2 circuit. When there is an open or short circuit in the shift solenoid valve DS1 or DS2 circuits, the ECM detects the problem, illuminates the MIL and stores the DTCs.

WIRING DIAGRAM

C200618E11
5.811,3.936 6.121,4.138 0.310,0.202 10 D2 5.811,4.123 6.201,4.325 0.390,0.202 10 ECM 5.637,1.194 6.057,1.396 0.421,0.202 10 DS1 5.335,2.495 5.561,2.697 0.226,0.202 10 78 5.335,1.32 5.537,1.522 0.202,0.202 10 79 5.637,2.363 6.127,2.565 0.490,0.202 10 DS2 3.235,1.06 3.597,1.262 0.362,0.202 10 DS1 3.631,2.495 3.857,2.697 0.226,0.202 10 10 3.631,1.32 3.832,1.522 0.202,0.202 10 5 3.235,2.232 3.617,2.433 0.383,0.202 10 DS2 1.49,1.615 3.126,1.817 1.636,0.202 10 Shift Solenoid Valve DS1 1.49,2.789 3.126,2.991 1.636,0.202 10 Shift Solenoid Valve DS2 1.17,3.721 1.480,3.923 0.310,0.202 10 D67 1.17,3.908 3.307,4.269 2.137,0.361 10 Transmission Wire (Continuously Variable Transaxle Assembly)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE SHIFT POSITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

In accordance with the display on the tester, perform the Active Test.

Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operates the shift solenoid valves to allow the gear ratio to be manually selected [1st - 2nd - 3rd - 4th - 5th]
Reference gear ratios:
1st (2.4 gear ratio max.) - 2nd (1.5) - 3rd (1.0) - 4th (0.7) - 5th (0.43 gear ratio min.)
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Used to check the operation of the shift solenoid valves.
NOTICE:

Performing this test at speeds other than those specified in "Vehicle Condition" will damage the transaxle.


[Vehicle Condition]
50 km/h (30 mph) or less
HINT:

Perform "Control the Shift Position" while monitoring "Shift Status" to confirm actual gear position.



Result
Result Proceed to
Gear ratio does not change A
Gear ratio changes B



A

2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)

B

6.REPLACE ECM
2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DS1 AND DS2)
a.
C199169E74
0.969,1.708 1.323,1.24 true 1.323,0.958 0.969,0.49 true 0.719,0.323 1.135,0.521 0.417,0.198 10 false DS1 0.073,0.063 0.385,0.26 0.313,0.198 10 false *1 0.688,1.698 1.104,1.896 0.417,0.198 10 false DS2

Disconnect the transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (DS1) - Body ground 20°C (68°F) 11 to 13 Ω
10 (DS2) - Body ground 20°C (68°F) 11 to 13 Ω


Text in Illustration
*1 Component without harness connected
(Transmission Wire)



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

8.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D2-78 (DS2) - Body ground 20°C (68°F) 11 to 13 Ω
D2-79 (DS1) - Body ground 20°C (68°F) 11 to 13 Ω




OK

4.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE ECM

NEXT

5.PERFORM INITIALIZATION
6.REPLACE ECM

NEXT

7.PERFORM INITIALIZATION
8.REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

NEXT

9.PERFORM INITIALIZATION