Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE FLUID
RM24M0E _52 Drivetrain _059572 K112 CVT _0292048 CONTINUOUSLY VARIABLE TRANSAXLE FLUID N

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE FLUID  ADJUSTMENT  


PROCEDURE

Hide 1. PRECAUTIONS AND WORK DESCRIPTION

a.

The K112 continuously variable transaxle does not have an oil filler tube or oil level gauge. When adding fluid, add fluid through the refill hole in the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the No. 1 transmission oil filler tube of the transaxle oil pan sub-assembly.

HINT:

"Overflow" indicates the condition under which fluid comes out of the overflow plug hole.



b.

When adding fluid, add the specified amount of fluid while the engine is cold. Then, warm up the engine to circulate the fluid in the continuously variable transaxle and adjust the fluid level with the engine idling at the specified fluid temperature.


c.

The K112 continuously variable transaxle requires Toyota Genuine CVT Fluid FE.


d.

When adjusting the fluid level, park the vehicle on level ground. Make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°.


e.

When adjusting the fluid level, turn off all electrical devices, such as the air conditioning, headlights and electric fan to reduce electrical load.


f.

The fluid temperature shown in the text is "A/T Oil Temperature 1" displayed on the intelligent tester.


g.

Fluid level adjustment should be performed according to the following procedure and notes.

C202513E34
1.885,2.313 2.729,2.667 2.729,2.667 2.729,2.719 true 5.604,2.375 6.198,2.615 6.198,2.615 6.198,2.719 false 1.563,3.375 4.625,3.563 3.063,0.188 12 false 3. ADJUST FLUID TEMPERATURE 0.302,5.875 2.25,6.219 1.948,0.344 12 false 4. ADJUST FLUID LEVEL 0.063,0.052 2.146,0.396 2.083,0.344 12 false Fluid Filling Procedure: 0.073,0.5 2.406,0.906 2.333,0.406 12 false 1. PERFORM INITIAL FILLING (When necessary) 4.021,0.5 7.083,0.729 3.063,0.229 12 false 2. ADD SPECIFIED AMOUNT OF FLUID 0.115,1.198 2.177,1.406 2.063,0.208 10 false Add fluid to the specified level. 4.042,0.917 6.708,1.229 2.667,0.313 10 false Add the correct amount of fluid specified for the operation that was performed. 0.188,2.521 1.354,3.115 1.167,0.594 10 false Add fluid until fluid comes out of the overflow plug hole. 0.323,7.698 2.125,8.688 1.802,0.99 10 false Keep the overflow plug open until the fluid flow slows and only drips come out. 0.302,6.281 2.771,6.76 2.469,0.479 10 false Drain excess fluid at the specified fluid temperature. 4.219,6.104 6.698,6.438 2.479,0.333 10 false If no fluid comes out, add fluid until fluid comes out of the overflow plug hole. 1.552,3.844 7,4.26 5.448,0.417 10 false Start the engine to circulate the fluid. Enter fluid temperature detection mode and engine idle speed control mode, and adjust the fluid temperature to the specified level. 6.375,1.76 6.99,2.26 0.615,0.5 10 false Specified Amount of Fluid 2.156,2.729 3.479,3.104 1.323,0.375 10 false No. 1 Transmission Oil Filler Tube 5.802,2.74 6.781,2.938 0.979,0.198 10 false Overflow Plug


Hide 2. WORK FLOW

a.

The adjustment should be performed according to the procedure referenced in the work flow below.

C285916E02
0.083,0.063 1.479,0.375 1.396,0.313 10 false Work Flow: 3.313,0.115 3.969,0.479 0.656,0.365 10 false START 0.865,1.198 3.063,1.375 2.198,0.177 10 false Operations that require initial filling 4.135,1.198 6.792,1.375 2.656,0.177 10 false Operations that do not require initial filling 1.125,4.24 6.021,4.646 4.896,0.406 10 false Activate fluid temperature detection mode and engine idle speed control mode 2.792,4.979 4.385,5.385 1.594,0.406 10 false Idling (Warm up the fluid) 2.604,3.094 4.479,3.5 1.875,0.406 10 false Add specified amount of fluid 2.24,6.479 5.052,6.75 2.813,0.271 10 false Drain excess and check the amount of fluid 2.969,8.594 4.208,9 1.24,0.406 10 false Finish up operation 3.385,9.385 3.729,9.792 0.344,0.406 10 false END 5.781,7.844 6.438,8.25 0.656,0.406 10 false Add fluid 3.292,7.833 3.896,8.24 0.604,0.406 10 false Overflow 2.458,5.719 4.719,6.125 2.26,0.406 10 false Normal operating fluid temperature 5.438,5.302 6.958,6 1.521,0.698 10 false Above normal operating fluid temperature 5.479,6.906 6.854,7.271 1.375,0.365 10 false No fluid comes out 3.042,7.156 4.063,7.458 1.021,0.302 10 false Fluid comes out 0.083,8.469 2.729,8.792 2.646,0.323 10 false Step 8. AFTER FILLING TRANSAXLE 0.083,0.594 2.729,0.917 2.646,0.323 10 false Step 4. PERFORM INITIAL FILLING 0.083,6.313 2.031,6.635 1.948,0.323 10 false Step 7. ADJUST FLUID LEVEL 0.073,3.854 2.76,4.156 2.688,0.302 10 false Step 6. ADJUST FLUID TEMPERATURE 0.083,2.969 2.302,3.292 2.219,0.323 10 false Step 5. ADD SPECIFIED AMOUNT OF FLUID 0.104,1.573 3.292,1.99 3.188,0.417 10 false Removal and installation of the drive shaft or the transmission oil pan sub-assembly 0.104,2.219 3.719,2.552 3.615,0.333 10 false Removal and installation of the torque converter assembly 3.844,1.552 6.906,1.75 3.063,0.198 10 false Disconnection of the oil cooler or oil cooler hose 3.844,1.896 5.375,2.073 1.531,0.177 10 false Repair of fluid leak, etc. 3.844,2.219 7.031,2.573 3.188,0.354 10 false Installation of a new continuously variable transaxle


Hide 3. BEFORE FILLING TRANSAXLE WITH FLUID

NOTICE:

If the transaxle is hot (fluid temperature is high), wait until the fluid temperature becomes the same as the ambient temperature before starting the following procedure (recommended fluid temperature: approximately 20°C [68°F])


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.

Remove the rear engine under cover LH.


Hide 4. PERFORM INITIAL FILLING

NOTICE:

After performing any of the following operations, it is not necessary to perform the initial filling procedure. Proceed to the Add Specified Amount of Fluid procedure (Step 5).


Operations that do not Require Initial Filling
·

Disconnection of the oil cooler or oil cooler hose.

·

Repair of fluid leak, etc.

·

Installation of a new transaxle.



a.
C128915

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the continuously variable transaxle.

NOTICE:
·

If fluid comes out after removing the overflow plug, wait until the fluid flow slows and only drops come out.

·

If fluid comes out, it is not necessary to perform the initial filling procedure. After checking the tightening torque of the No. 1 transmission oil filler tube, temporarily install the overflow plug.




b.
C287691E02
2.698,0.802 2.615,0.802 2.615,0.802 2.396,1.021 true 2.729,0.719 2.896,0.917 0.167,0.198 10 false *1

Using a 6 mm hexagon socket wrench, check that the No. 1 transmission oil filler tube is tightened to the specified torque.

Text in Illustration
*1 No. 1 Transmission Oil Filler Tube

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)

NOTICE:

If the No. 1 transmission oil filler tube is not tightened to the specified torque, the amount of fluid cannot be precisely adjusted.


HINT:

To check the torque of the No. 1 transmission oil filler tube, insert the hexagon socket wrench into the overflow plug hole.



c.
C189218

Remove the refill plug and gasket from the continuously variable transaxle.


d.

Perform initial filling.

i.
C287692

Add fluid to the refill hole until it flows out of the overflow plug hole.

NOTICE:

Use Toyota Genuine CVT Fluid FE.




e.
C287693

Wait until the fluid flow slows and only drops come out.


f.

Temporarily install the gasket and overflow plug.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



Hide 5.ADD SPECIFIED AMOUNT OF FLUID

a.

Remove the refill plug and gasket from the continuously variable transaxle (when initial filling was not performed).


b.

Add fluid to the refill hole using the correct amount of fluid as listed in the table below.

NOTICE:

Refill amount differs depending on the operation that was performed.


Standard Capacity:
Operation Performed Refill Amount
·

Disconnection of the oil cooler or cooler hose.

·

Repair of fluid leak, etc.


0.6 liters (0.6 US qts, 0.5 Imp. qts)
Installation of a new continuously variable transaxle (a new torque converter assembly has been installed). 6.2 liters (6.6 US qts, 5.5 Imp. qts)
Installation of a new continuously variable transaxle (the old torque converter assembly has been reused). 5.6 liters (5.9 US qts, 4.9 Imp. qts)
·

Removal and installation of the drive shaft.

·

Removal and installation of the oil pan.


2.1 liters (2.2 US qts, 1.8 Imp. qts)
Removal and installation of the torque converter assembly (a new torque converter assembly has been installed). 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Removal and installation of the torque converter assembly (the old torque converter assembly has been reused). 2.9 liters (3.1 US qts, 2.6 Imp. qts)



c.
C189218

Temporarily install the gasket and refill plug to avoid fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



d.

Lower the vehicle.


Hide 6.ADJUST FLUID TEMPERATURE

a.

When using the intelligent tester:

i.

Connect the intelligent tester to the DLC3 with the engine switch off.


ii.

Turn the engine switch on (IG) and turn the intelligent tester on.


iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / A/T Oil Temperature 1.


v.

According to the display on the intelligent tester, turn on the Connect the TC and TE1 Active Test.

HINT:

The indicator lights on the combination meter blink to indicate the DTC output during the Active Test.




b.

When not using the intelligent tester:

i.
C367918E02
1.604,0.469 1.583,0.906 true 1.771,1.813 1.76,1.469 true 0.125,0.083 0.438,0.281 0.313,0.198 10 false *1 1.51,0.302 1.823,0.5 0.313,0.198 10 false CG 1.698,1.823 2.01,2.021 0.313,0.198 10 false TC

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the engine switch off.

SST
09843-18040  

Text in Illustration
*1 Front view of DLC3



c.

Depress and hold the brake pedal.


d.

Start the engine.

NOTICE:

Check that electrical systems such as the air conditioning system, audio system and lighting system are off.



e.

Slowly move the shift lever from P to D, and then back to P (keep the shift lever in each position for approximately 3 seconds).

HINT:

Slowly move the shift lever to circulate the fluid through each part of the continuously variable transaxle.



f.
C224565E02
1.469,0.25 1.354,0.25 1.354,0.25 1.24,0.833 false 2.667,1.563 2.573,1.563 2.573,1.563 2.448,2.281 false 2,3.115 2.063,3.115 2.063,3.115 2.135,2.74 false 1.51,0.167 2.677,0.333 1.167,0.167 10 false Less than 1.5 sec. 0.802,1.563 1.729,1.729 0.927,0.167 10 false 6 sec. or more 1.604,2.281 2,2.458 0.396,0.177 10 false 2 sec. 2.719,1.479 3.323,1.896 0.604,0.417 10 false Indicator Light On 0.156,0.656 0.302,0.823 0.146,0.167 10 false P 0.156,1.01 0.302,1.177 0.146,0.167 10 false N 0.156,1.313 0.302,1.479 0.146,0.167 10 false D 0.594,3.021 2.042,3.323 1.448,0.302 10 false Shift Indicator Light [D]

While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of less than 1.5 seconds for 6 seconds or more.

NOTICE:

Do not pause for more than 1.5 seconds.


HINT:

Performing this operation will cause the vehicle to enter fluid temperature detection mode.



g.
C137197

Check that the D shift indicator comes on for 2 seconds.

HINT:
·

When fluid temperature detection mode is activated, the D shift indicator on the combination meter comes on for 2 seconds.

·

If the D shift indicator does not come on for 2 seconds, return to the step where terminals 13 (TC) and 4 (CG) are first connected and perform the procedure again.




h.

Move the shift lever from N to P.


i.

Release the brake pedal.


j.

Disconnect the terminals of the DLC3.

i.

When using the intelligent tester:

·

According to the display on the intelligent tester, turn off the Connect the TC and TE1 Active Test.



ii.

When not using the intelligent tester:

·

Remove SST from terminals 13 (TC) and 4 (CG).


NOTICE:

Make sure that terminals 13 (TC) and 4 (CG) are not connected. If the terminals are connected, the fluid level cannot be precisely adjusted due to fluctuations in engine speed.


HINT:
·

Disconnecting terminals 13 (TC) and 4 (CG) activates engine idle speed control mode.

·

In engine idle speed control mode, engine idle speed control starts when the fluid temperature reaches the specified value and the engine speed is maintained.

·

Even after terminals 13 (TC) and 4 (CG) are disconnected, fluid temperature detection mode remains active until the engine switch is turned off.





k.

Adjust the fluid temperature to the normal operating temperature.

i.

Check the fluid temperature by monitoring the D shift indicator.

HINT:
·

In fluid temperature detection mode, the D shift indicator comes on, goes off, or blinks depending on the fluid temperature.

·

The fluid filling procedure should be performed when the D shift indicator is on (the fluid temperature is within the fluid level adjustment temperature range).




ii.

Adjust the fluid temperature.

·

If the D shift indicator is off [Below Normal Operating Temperature: 30°C (86°F) or less]: Warm up the engine with the engine idling in engine idle speed control mode until the D shift indicator turns on.


·

If the D shift indicator is on [Normal Operating Temperature: 30 to 40°C (86 to 104°F)]: Immediately proceed to the Adjust Fluid Level procedure (Step 7).


·

If the D shift indicator is blinking [Above Normal Operating Temperature: 40°C (104°F) or more]: Stop the engine and wait until the fluid temperature drops to 30°C (86°F) or less (the D shift indicator goes off). Then perform the Adjust Fluid Temperature procedure again from the beginning.


Relationship between Fluid Level Adjustment Temperature and D Shift Indicator:
Below Fluid Level Adjustment Temperature Fluid Level Adjustment Temperature Above Fluid Level Adjustment Temperature
Fluid Temperature ("A/T Oil Temperature 1" displayed on the intelligent tester) 30°C (86°F) or less 30 to 40°C (86 to 104°F) 40°C (104°F) or more
D Shift Indicator Off On Blinks




Hide 7.ADJUST FLUID LEVEL

CAUTION:

Use caution while the engine is idling and the radiator fan is operating.


a.

Lift the vehicle.

NOTICE:

Set the vehicle on a lift so that the vehicle is kept level when it is lifted up (make sure that the tilt angle from the front to rear of the vehicle is within +/- 1°).



b.
C128915

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket.

CAUTION:

Be careful as the fluid coming out of the overflow plug hole is hot.



c.

Check the amount of fluid that comes out of the overflow plug hole.

·

If the amount of fluid that comes out of the overflow plug hole is large, proceed to *1.

·

If no fluid comes out of the overflow plug hole, proceed to *2.


NOTICE:

If only a small amount of fluid (approximately 5 cc) comes out of the overflow plug hole, then only fluid remaining in the No. 1 transmission oil filler tube has come out. This is not considered to be overflow.



d.
C287692

*2:

If no fluid comes out of the overflow plug hole, remove the refill plug and gasket. Then add transaxle fluid through the refill hole until fluid comes out of the overflow plug hole. Wait until the fluid flow slows and only drops come out.

NOTICE:

Use Toyota Genuine CVT Fluid FE.



e.

*1:

If the amount of fluid that comes out of the overflow plug hole is large, wait until the fluid flow slows and only drops come out.

C287694

HINT:

The fluid flow will not stop completely because the fluid continues to expand as its temperature increases.



f.

Install a new gasket and the overflow plug.

Torque:
40 N*m (408 kgf*cm, 29 ft.*lbf)


g.
C189218

Install a new gasket and the refill plug.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


h.

Lower the vehicle.


i.

Turn the engine switch off.

HINT:

Turning the engine switch off exits fluid temperature detection mode.



j.

Remove the intelligent tester from the DLC3 (when using the intelligent tester).


Hide 8. AFTER FILLING TRANSAXLE

a.

Lift the vehicle.


b.

Clean each part.


c.

Check for fluid leaks.


d.

Install the rear engine under cover LH.


e.

Lower the vehicle.