Home › Drivetrain › K112 (CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › 2013.04–2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292052 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K112 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 12311A 2.REMOVE FRONT ENGINE MOUNTING BRACKET

C191112

a.

Remove the 3 bolts and front engine mounting bracket from the continuously variable transaxle assembly.


Hide 12321A 3.REMOVE REAR ENGINE MOUNTING BRACKET

C211787

a.

Remove the 3 bolts and rear engine mounting bracket from the continuously variable transaxle assembly.


Hide 28100 4.REMOVE STARTER ASSEMBLY

a.
A133097

Disconnect the connector from the starter assembly.


b.

Open the terminal cap, remove the nut and disconnect the starter wire.


c.
A133101

Remove the 2 bolts and starter assembly from the continuously variable transaxle assembly.


Hide 82121 5.DISCONNECT ENGINE WIRE

a.
C264695

Disconnect the transmission wire connector, park/neutral position switch connector, and 3 revolution sensor connectors, and detach the 4 wire harness clamps from the continuously variable transaxle assembly.


b.
C189448

Disconnect the oil pressure sensor connector and detach the 2 wire harness clamps from the continuously variable transaxle assembly.


Hide 6.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C264696E01
2.284,1.081 2.577,0.635 2.577,0.635 2.835,0.635 false 2.852,0.549 3.056,0.732 0.205,0.184 10 *a

Remove the bolt and disconnect the ground cable from the wire harness clamp bracket.

Text in Illustration
*1 Ground Cable


b.

Remove the 2 bolts, shift cable bracket and 2 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 33493B 7.REMOVE OIL COOLER (w/o Air Cooled Transmission Oil Cooler)

a.
C225344

Release the 3 clamps and disconnect the water by-pass hose and 2 oil cooler hoses from the oil cooler.


b.
C268463

Release the 2 clamps and remove the 2 oil cooler hoses from the continuously variable transaxle assembly.


c.
C225341

Remove the 3 bolts and oil cooler from the continuously variable transaxle assembly.


Hide 33493B 8.REMOVE OIL COOLER (w/ Air Cooled Transmission Oil Cooler)

a.
C264697

Release the 4 clamps and remove the 2 oil cooler hoses from the oil cooler and continuously variable transaxle assembly.


b.
C264698

Release the 2 clamps and disconnect the 2 water by-pass hoses from the oil cooler.


c.
C264772

Remove the 3 bolts and oil cooler from the continuously variable transaxle assembly.


Hide 11361J 9.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
U189792

Remove the flywheel housing under cover from the engine assembly.


Hide 30400 10.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C224431

Turn the crankshaft to gain access and remove the 6 drive plate and torque converter assembly setting bolts while holding the crankshaft pulley bolt with a wrench.


b.
C367459E02
1.563,0.365 2.896,0.281 true 2.917,0.198 3.229,0.396 0.313,0.198 10 false *1

Remove the 9 bolts and continuously variable transaxle assembly from the engine assembly.

Text in Illustration
*1 Knock Pin

NOTICE:

To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



Hide 33823 11.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C189450

a.

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 12325A 12.REMOVE ENGINE MOUNTING BRACKET LH

C130638

a.

Remove the 3 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.


Hide 32000A 13.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C224642

Remove the torque converter assembly from the continuously variable transaxle assembly.


Hide 30400E 14.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is the possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from moving, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter is not attached to it.

·

Do not use an air gun until the torque converter has been installed, as it could cause dust and foreign matter to be stirred up.



a.
C208788E19
2.396,2.063 2.396,2.677 false 2.281,2.708 2.604,3 0.323,0.292 10 false SST

Clean the tips of both claws of SST and the center bolt.


b.

Using SST, remove the CVT oil pump type T oil seal.

SST
09308-10010  

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.



Hide 32000A 15.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101 16.INSPECT DRIVE PLATE & RING GEAR SUB-ASSEMBLY