Home › Drivetrain › K112 (CVT) › SPEED SENSOR › from 2016.05
RM24M0E _52 Drivetrain _059572 K112 CVT _0292057 SPEED SENSOR G

K112 CVT  SPEED SENSOR  INSPECTION  


PROCEDURE

Hide 89413B 1.INSPECT TRANSMISSION REVOLUTION SENSOR (NIN)

C200614E06
0.057,0.004 0.298,0.206 0.240,0.202 10 *a 1.304,1.683 1.604,1.17 false 1.081,1.709 1.527,1.911 0.446,0.202 10 NIN+ 2.152,1.683 1.852,1.17 false 2.046,1.709 2.492,1.911 0.446,0.202 10 NIN-

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (NIN-) - 2 (NIN+) 20°C (68°F) 560 to 680 Ω


Text in Illustration
*a Component without harness connected
(Transmission Revolution Sensor (NIN))

If the result is not as specified, replace the transmission revolution sensor (NIN).


Hide 89413B 2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)

a.
C366273E04
1.302,1.24 1.563,0.802 true 1.427,2.271 1.521,2.073 false 2.125,1.271 1.833,0.833 true 0.292,2.74 0.458,2.625 true 0.833,2.635 1,2.719 true 2.594,3.104 2.438,2.844 false 2.26,3.979 2.49,3.729 false 1.417,4.354 1.677,4.208 false 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.115,1.26 1.427,1.458 0.313,0.198 10 false NTB 2.031,1.292 2.344,1.49 0.313,0.198 10 false NTO 2.573,3.125 2.885,3.323 0.313,0.198 10 false *1 1.313,2.292 1.625,2.49 0.313,0.198 10 false *d 2.469,3.563 2.781,3.76 0.313,0.198 10 false *b 1.281,4.344 1.594,4.542 0.313,0.198 10 false *c 0.135,2.698 0.448,2.896 0.313,0.198 10 false *2 1.052,2.688 1.365,2.885 0.313,0.198 10 false *1

Connect the battery to the transmission revolution sensor (NT) as shown in the illustration.

Text in Illustration
*1 Battery
*a Component without harness connected
(Transmission Revolution Sensor (NT))
*b Magnet
*c 5 mm or less
*d Ammeter


b.

Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NTO) - 2 (NTB) Low signal 4 to 8 mA
High signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NT).


Hide 89413B 3.INSPECT TRANSMISSION REVOLUTION SENSOR (NOUT)

a.
C366273E03
1.302,1.24 1.563,0.802 true 1.427,2.271 1.521,2.073 false 2.125,1.271 1.833,0.833 true 0.292,2.74 0.458,2.625 true 0.833,2.635 1,2.719 true 2.594,3.104 2.438,2.844 false 2.26,3.979 2.49,3.729 false 1.417,4.354 1.677,4.208 false 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 1.073,1.26 1.521,1.49 0.448,0.229 10 false NOTB 2.031,1.292 2.5,1.521 0.469,0.229 10 false NOTO 2.573,3.125 2.885,3.323 0.313,0.198 10 false *1 1.313,2.292 1.625,2.49 0.313,0.198 10 false *d 2.469,3.563 2.781,3.76 0.313,0.198 10 false *b 1.281,4.344 1.594,4.542 0.313,0.198 10 false *c 0.135,2.698 0.448,2.896 0.313,0.198 10 false *2 1.052,2.688 1.365,2.885 0.313,0.198 10 false *1

Connect the battery to the transmission revolution sensor (NOUT) as shown in the illustration.

Text in Illustration
*1 Battery
*a Component without harness connected
(Transmission Revolution Sensor (NOUT))
*b Magnet
*c 5 mm or less
*d Ammeter


b.

Wave a magnetic object left and right 5 mm (0.197 in.) or less from the tip of the transmission revolution sensor (NOUT) to output a high/low signal while measuring the current.

NOTICE:

Make sure to wave the magnetic object during the inspection. The current will not change unless the magnetic object is moved as shown in the illustration.



c.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
1 (NOTO) - 2 (NOTB) Low signal 4 to 8 mA
High signal 12 to 16 mA


If the result is not as specified, replace the transmission revolution sensor (NOUT).