Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM C

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  B2281  "P" Signal Malfunction  


DESCRIPTION

The ECM and the shift lock control ECU are connected by a cable and the CAN. If the cable information and CAN information are inconsistent, this DTC will be output.

HINT:

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2281 Cable information and CAN information between main body ECU and shift lock control ECU are inconsistent
·

Instrument panel junction block LH (Main body ECU)

·

Shift lock control ECU

·

Wire harness or connector



WIRING DIAGRAM

B157544E02
1.385,2.425 1.573,2.590 0.188,0.165 10 11 1.329,2.642 1.612,2.793 0.283,0.151 10 G25 1.018,2.655 1.216,2.816 0.198,0.161 10 P2 0.135,3.223 1.599,3.372 1.464,0.149 10 Shift Lock Control ECU 2.288,2.116 2.620,2.267 0.332,0.151 10 ECM 2.487,1.526 2.812,1.674 0.325,0.149 10 CAN 4.266,1.752 4.591,1.901 0.325,0.149 10 CAN 6.052,1.535 6.377,1.684 0.325,0.149 10 CAN 2.688,0.792 2.813,0.954 0.126,0.162 10 P 4.084,0.695 5.265,1.041 1.181,0.346 10 From Park/Neutral Position Switch 5.736,2.431 5.857,2.587 0.121,0.156 10 2 5.647,2.641 5.930,2.794 0.283,0.152 10 G60 5.857,3.221 6.877,3.374 1.020,0.152 10 Main Body ECU 6.05,2.641 6.194,2.794 0.144,0.152 10 P

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the intelligent tester main switch on.


c.

Read the DATA LIST according to the displays on the tester.

Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Shift P Sig Shift P Signal / ON or OFF ON: Shift P signal ON (Shift position is P)
OFF: Shift P signal OFF (Shift position is not P)
-

OK:

"ON" (P signal is ON) and "OFF" (P signal is OFF) appear on the screen.


HINT:

If the result is not as specified, there may be a malfunction with the shift lock control ECU (See page Drivetrain>U660E (AUTOMATIC TRANSMISSION / TRANSAXLE)>SHIFT LOCK SYSTEM>ON-VEHICLE INSPECTION).




OK

GO TO SHIFT CONTROL SYSTEM

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SHIFT LOCK CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SHIFT LOCK CONTROL ECU)
a.
B460083E01
0.5,1.25 0.917,1.5 0.417,0.25 0.5,3.75 0.917,4 0.417,0.25 1.938,1.365 2.365,1.365 false 1.948,4.104 2.49,3.896 false 0.125,0.073 2.385,0.563 2.26,0.49 10 false Front view of wire harness connector: (to Main body ECU) 2.427,1.281 2.979,1.594 0.552,0.313 10 false P 2.542,3.781 3.094,4.094 0.552,0.313 10 false P2 0.563,3.781 1.115,4.094 0.552,0.313 10 false G25 0.167,2.49 2.458,2.948 2.292,0.458 10 false Front view of wire harness connector: (to Shift Lock Control ECU) 0.563,1.281 1.115,1.594 0.552,0.313 10 false G60

Disconnect the G25 and G60 ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Terminal No. Condition Specified Condition
G60-2 (P) - G25-11 (P2) Always Below 1 Ω
G60-2 (P) - Body ground Always 10 kΩ or higher




OK

3.CHECK MAIN BODY ECU OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU OPERATION
a.

After replacing the main body ECU with a normally functioning ECU, check that the engine can start normally. Make sure the brake pedal is depressed and the shift position is P at this time.


b.

Check that the engine switch mode can be changed by pushed the engine switch.

HINT:

Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.


OK:

Engine starts normally.


HINT:

If engine does not start (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Engine does not Start).




OK

END (MAIN BODY ECU DEFECTIVE)

NG

GO TO SHIFT CONTROL SYSTEM