Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM C

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  B2276  ACCR Signal Circuit Malfunction  


DESCRIPTION

The main body ECU will set this DTC if the ACCR signal sent from the ECM is ON for 40 seconds or more.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2276 ACCR output circuit inside main body ECU or other related circuit is malfunctioning
·

Instrument panel junction block LH (Main body ECU)

·

ECM

·

Wire harness or connector



WIRING DIAGRAM

B112452E16
0.919,3.083 1.199,3.236 0.280,0.153 10 A7 0.919,3.242 1.268,3.395 0.349,0.153 10 ECM 5.597,3.083 5.896,3.236 0.299,0.153 10 G58 5.597,3.242 6.619,3.415 1.022,0.173 10 Main Body ECU 1.612,1.611 1.814,1.760 0.202,0.149 10 13 5.661,1.701 6.089,1.872 0.428,0.171 10 ACCR 1.123,1.702 1.547,1.873 0.424,0.171 10 ACCR 5.474,1.611 5.592,1.763 0.119,0.152 10 3

PROCEDURE

1.CHECK DTC OUTPUT
a.

Delete the DTCs (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>DTC CHECK / CLEAR).

HINT:

After all DTCs are cleared, check if the trouble occurs again 50 seconds after the engine switch is turned on (IG).



b.

Check for DTCs again.

OK:

No DTC B2276 is output.




OK

CHECK INTERMITTENT PROBLEMS

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
a.

Disconnect the G58 ECU connector.

A393996E01
0.75,1 1.167,1.25 0.417,0.25 5.583,2.25 6,2.5 0.417,0.25 1.156,1.563 1.698,1.385 false 4.813,2.292 5.573,1.198 false 0.292,0.104 2.563,0.51 2.271,0.406 10 false Front view of wire harness connector: (to Main Body ECU) 0.823,1.042 1.375,1.323 0.552,0.281 10 false G58 0.708,1.5 1.26,1.781 0.552,0.281 10 false ACCR 4.021,0.094 6.271,0.521 2.25,0.427 10 false Front view of wire harness connector: (to ECM) 5.688,2.292 6.24,2.573 0.552,0.281 10 false A7 4.563,2.313 5.115,2.594 0.552,0.281 10 false ACCR


b.

Disconnect the A7 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G58-3 (ACCR) - A7-13 (ACCR) Always Below 1 Ω
G58-3 (ACCR) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU
a.
U188845E02
1.833,2.635 2.5,2.313 false 0.323,0.135 2.542,0.51 2.219,0.375 10 false Component with harness connected: (Main Body ECU) 2.552,2.167 2.969,2.323 0.417,0.156 10 false ACCR 2.542,2.646 2.875,2.844 0.333,0.198 10 false G58

Reconnect the connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
G58-3 (ACCR) - Body ground Brake pedal depressed, shift P position, engine switch is pushed once → on (IG) 0.1 to 0.8 V (*1) → Output voltage at terminal AM1 or AM2 is -2 V or more.


HINT:
·

*1: Voltage is output only when the engine is cranking.

·

Terminal AM1: G57-6

·

Terminal AM2: G58-1





OK

4.CHECK MAIN BODY ECU OPERATION

NG

4.CHECK MAIN BODY ECU OPERATION
a.

After replacing the main body ECU with a normally functioning ECU, check that the engine starts. Make sure the brake pedal is depressed and the shift position is P at this time.


b.

Check that the engine switch mode can be changed by pushing the engine switch.

HINT:

Without depressing the brake pedal, push the engine switch repeatedly. Engine switch mode should turn from off to on (ACC) to on (IG) and back to off. With the brake pedal depressed, push the engine switch repeatedly. Engine switch mode should turn to ENGINE START from any status.


OK:

Engine starts normally.


HINT:

If engine does not start (See page Engine / Hybrid System>2GR-FE STARTING>SMART ENTRY AND START SYSTEM>Engine does not Start).




OK

END (MAIN BODY ECU DEFECTIVE)

NG