Home › Engine / Hybrid System › 2GR-FE STARTING › SMART ENTRY AND START SYSTEM › from 2016.05
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292072 SMART ENTRY AND START SYSTEM C

2GR-FE STARTING  SMART ENTRY AND START SYSTEM  B2286  Runnable Signal Malfunction  


DESCRIPTION

This DTC is output when serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM are inconsistent.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.

After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2286 Serial communication signals and CAN communication signals in the circuit between the main body ECU and ECM are inconsistent.
·

CAN communication system

·

ECM

·

Instrument panel junction block LH (Main body ECU)

·

Wire harness or connector



WIRING DIAGRAM

B159477E02
0.938,0.994 1.244,1.159 0.306,0.165 10 TAC 0.844,3.591 1.244,3.756 0.400,0.165 10 TACH 0.926,4.656 1.244,4.821 0.318,0.165 10 CAN 6,3.591 6.399,3.756 0.400,0.165 10 TACH 6,4.656 6.318,4.821 0.318,0.165 10 CAN 3.492,4.901 3.810,5.066 0.318,0.165 10 CAN 0.57,1.766 0.868,1.931 0.298,0.165 10 G15 0.57,1.933 0.979,2.098 0.409,0.165 10 DLC3 0.564,5.875 0.917,6.040 0.353,0.165 10 ECM 0.564,5.714 0.845,5.880 0.281,0.165 10 A7 5.872,5.855 6.903,6.020 1.031,0.165 10 Main Body ECU 5.872,5.695 6.166,5.860 0.294,0.165 10 G59 1.332,3.475 1.535,3.642 0.202,0.167 10 15 1.332,0.886 1.461,1.052 0.129,0.167 10 9 5.728,3.475 5.857,3.642 0.129,0.167 10 8

PROCEDURE

1.CHECK OPERATION OF TACHOMETER
a.

Run the engine and check if the function of the tachometer in the combination meter is normal.

OK:

Actual engine revolution speed and the revolution indicated on the tachometer are the same.




OK

2.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
2.CHECK DTC OUTPUT (CAN COMMUNICATION SYSTEM)

b.

Check for CAN communication system (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

HINT:

If the DTCs for the CAN communication system malfunction are output, inspect those DTCs first (See page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART).


OK:

No DTC is output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM)
a.

Disconnect the A7 ECM connector.

B460085E01
1.833,2.333 2.25,2.583 0.417,0.25 5.083,2.333 5.5,2.583 0.417,0.25 2.094,1.729 2.656,1.5 false 4.604,2.354 5.625,1.396 false 0.917,0.125 3.177,0.563 2.26,0.438 10 false Front view of wire harness connector: (to Main Body ECU) 2.698,1.375 3.188,1.635 0.49,0.26 10 false TACH 4.24,0.167 6.51,0.615 2.271,0.448 10 false Front view of wire harness connector: (to ECM) 1.906,2.375 2.396,2.635 0.49,0.26 10 false G59 5.188,2.365 5.677,2.625 0.49,0.26 10 false A7 4.229,2.344 4.719,2.604 0.49,0.26 10 false TACH


b.

Disconnect the G59 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G59-8 (TACH) - A7-15 (TACH) Always Below 1 Ω
G59-8 (TACH) or A7-15 (TACH) - Body ground Always 10 kΩ or higher




OK

4.READ VALUE USING INTELLIGENT TESTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER
a.

Reconnect the connectors.


b.

Connect the intelligent tester to the DLC3.


c.

Check the DATA LIST for proper functioning of the engine.

HINT:

When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.


Body:
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
E/G Cond Engine condition/STOP or RUN STOP: Engine is stopped
RUN: Engine is running
-

OK:

STOP (engine is stopped) and RUN (engine is running) appear on the screen.




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG