Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START C

2GR-FE STARTING  PUSH-BUTTON START  B2273  Ignition 2 Monitor Malfunction  


DESCRIPTION

This DTC is output when a malfunction occurs in the IG2D output circuit, which is between the IG2 relay actuation circuit inside the main body ECU and the IG2 relay.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored. After the man body ECU is replaced, perform the registration procedures for the engine immobiliser system.


DTC No. DTC Detection Condition Trouble Area
B2273 IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
·

Instrument panel junction block LH (Main body ECU)

·

IG2 relay

·

Wire harness or connector



WIRING DIAGRAM

B167136E01
0.103,1.351 0.897,1.510 0.795,0.159 10 from Battery 0.076,2.316 1.076,2.473 1.000,0.158 10 to Each System 2.898,1.497 3.150,1.649 0.252,0.152 10 IG2 2.864,3.182 3.116,3.334 0.252,0.152 10 IG2 2.474,2.215 2.581,2.378 0.107,0.163 10 3 2.474,2.802 2.581,2.965 0.107,0.163 10 2 3.398,2.215 3.504,2.378 0.107,0.163 10 5 3.398,2.802 3.504,2.965 0.107,0.163 10 1 5.533,2.802 5.719,2.965 0.186,0.163 10 11 5.842,2.913 6.239,3.076 0.397,0.163 10 IG2D 5.849,3.616 6.131,3.776 0.282,0.160 10 G58 5.849,3.769 6.863,3.929 1.014,0.160 10 Main Body ECU

PROCEDURE

1.READ VALUE USING GTS (IG2 RELAY MONITOR (INSIDE))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / IG2 Relay Mon2.


d.

Read the display on the tester.

Main Body ECU
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG2 Relay Monitor(Inside) IG2 inner relay monitor / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-

OK:

When the engine switch is turned on (IG), ON is displayed on the tester.




OK

2.CHECK ENGINE SWITCH CONDITION

NG

3.INSPECT IG2 RELAY
2.CHECK ENGINE SWITCH CONDITION
a.

Ensure the electrical key is inside the cabin.


b.

Check that the power source mode changes as shown below each time the engine switch is pushed.

OK:

off → on (ACC) → on (IG) → off




OK

NORMAL

NG

3.INSPECT IG2 RELAY
a.

Remove the IG2 relay from the engine room relay block No. 1.


B426341E08
2.625,0.75 2.927,0.5 false 2.469,1.135 2.896,0.969 false 2.469,1.625 2.906,1.458 false 2.031,0.708 1.719,0.469 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 2 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.323 1.396,1.542 0.219,0.219 10 false 1 1.563,0.354 1.781,0.573 0.219,0.219 10 false 1 2.99,0.875 3.208,1.094 0.219,0.219 10 false 5 2.979,1.375 3.198,1.594 0.219,0.219 10 false 3 2.969,0.417 3.188,0.635 0.219,0.219 10 false 2

b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)




OK

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE IG2 RELAY

4.CHECK HARNESS AND CONNECTOR (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)
a.

Remove the IG2 relay from the engine room relay block No. 1.


b.

Disconnect the G58 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Specified Condition
Relay block IG2 relay terminal 1 - G58-11 (IG2D) Below 1 Ω
Relay block IG2 relay terminal 2 - Body ground Below 1 Ω
Relay block IG2 relay terminal 1 or G58-11 (IG2D) - Body ground 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR