When the engine switch is pushed with the electrical key in the cabin, the main body ECU receives signals to switch the power source mode.
To allow use of the GTS to inspect the push-button start function when the engine switch is off, repeat opening and closing any of the doors. Opening and closing a door establishes communication between the GTS and the main body ECU. (Opening and closing a door can also be simulated by operating a door courtesy light switch.)
Inspect interior detection area.
When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.
Engine switch illuminates in green.
If the engine switch does not illuminate, perform troubleshooting according to the PROBLEM SYMPTOMS TABLE (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).
| *a | Inspection Point |
OK
NG
Remove the AM2 No. 2 and F/B BATT fuses from the engine room junction block No. 1.
Measure the resistance of the fuse.
Below 1 Ω
OK
NG
Check that the connectors are securely connected and the terminals are not deformed or loose.
The connectors are securely connected and the terminals are not deformed or loose.
OK
NG
Disconnect the G57 and G58 ECU connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G57-6 (AM1) - Body ground | Always | 11 to 14 V |
| G58-1 (AM2) - Body ground | Always | 11 to 14 V |
OK
NG
Disconnect the 4A and G59 ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
|---|---|---|
| 4A-3 (GND2) - Body ground | Always | Below 1 Ω |
| G59-1 (GND1) - Body ground | Always | Below 1 Ω |
OK
NG
Delete the DTCs (See page Engine / Hybrid System>2GR-FE STARTING>PUSH-BUTTON START>DTC CHECK / CLEAR).
After all the DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).
Check for DTCs again.
No DTC is output.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Check the DATA LIST for proper functioning of the start switches 1 and 2.
When using the GTS with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Switch1 | Start switch 1/ON or OFF | ON: Engine switch is pushed
OFF: Engine switch is not pushed |
- |
| Start Switch2 | Start switch 2/ON or OFF | ON: Engine switch is pushed
OFF: Engine switch is not pushed |
- |
ON (engine switch is pushed) and OFF (engine switch is not pushed) appear on the screen.
OK
NG
Remove the engine switch.
| *a | Component without harness connected
(Engine Switch) |
- | - |
Measure the resistance of the switch.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 7 (SS1) - 5 (GND) | Pushed | Below 1 Ω |
| 2 (SS2) - 5 (GND) | Pushed | Below 1 Ω |
| 7 (SS1) - 5 (GND) | Not pushed | 10 kΩ or higher |
| 2 (SS2) - 5 (GND) | Not pushed | 10 kΩ or higher |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G31-7 (SS1) - G57-17 (SSW1) | Always | Below 1 Ω |
| G31-2 (SS2) - G57-16 (SSW2) | Always | Below 1 Ω |
| G31-5 (GND) - Body ground | Always | Below 1 Ω |
| G31-7 (SS1) or G57-17 (SSW1) - Body ground | Always | 10 kΩ or higher |
| G31-2 (SS2) or G57-16 (SSW2) - Body ground | Always | 10 kΩ or higher |
OK
NG