Home › Engine / Hybrid System › 2GR-FE STARTING › PUSH-BUTTON START › from 2016.05
RM24M0E _51 Engine / Hybrid System _059574 2GR-FE STARTING _0292073 PUSH-BUTTON START J

2GR-FE STARTING  PUSH-BUTTON START  Engine Switch Indicator Circuit  


DESCRIPTION

Engine start conditions or system malfunctions can be checked by the status of the engine switch indicator light.

Engine switch indicator light condition:
Power Source Mode/Condition Indicator Light Condition
Brake pedal released Brake pedal depressed, shift lever in P or N
off OFF ON (Green) (When key and vehicle IDs match)
on (ACC, IG) ON (Amber) ON (Green)
Engine running OFF OFF
Steering lock not unlocked Flashes (Green) for 15 sec. Flashes (Green) for 15 sec.
System malfunction Flashes (Amber) for 15 sec. Flashes (Amber) for 15 sec.

HINT:

When the main body ECU is replaced with a new one and the negative (-) battery terminal is connected, the power source mode becomes the IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored. After the main body ECU is replaced, perform the registration procedures for the engine immobiliser system.


WIRING DIAGRAM

B157549E03
1.109,1.538 1.227,1.705 0.118,0.167 10 5 1.334,1.538 1.694,1.705 0.359,0.167 10 GND 4.419,1.538 4.792,1.705 0.373,0.167 10 INDS 4.891,1.538 5.085,1.705 0.194,0.167 10 12 5.836,1.538 6.030,1.705 0.194,0.167 10 15 6.111,1.647 6.487,1.814 0.376,0.167 10 INDS 6.111,2.483 6.521,2.650 0.411,0.167 10 INDW 6.111,3.318 6.521,3.485 0.411,0.167 10 SWIL 5.836,2.38 6.030,2.547 0.194,0.167 10 14 5.836,3.19 6.030,3.358 0.194,0.167 10 25 4.891,2.37 5.085,2.537 0.194,0.167 10 13 4.891,3.205 5.085,3.372 0.194,0.167 10 11 4.394,2.377 4.792,2.544 0.398,0.167 10 INDW 4.419,3.212 4.792,3.380 0.373,0.167 10 SWIL 1.965,1.929 2.884,2.096 0.919,0.167 10 Indicator Light 1.965,2.779 2.884,2.946 0.919,0.167 10 Indicator Light 2.068,3.575 2.811,3.743 0.744,0.167 10 Illumination 1.334,2.37 1.694,2.537 0.359,0.167 10 COM 1.109,2.384 1.227,2.551 0.118,0.167 10 4 2.766,3.926 3.054,4.081 0.288,0.155 10 G31 2.766,4.078 3.668,4.233 0.902,0.155 10 Engine Switch 6.012,5.781 6.300,5.937 0.288,0.155 10 G57 6.012,5.933 7.028,6.089 1.016,0.155 10 Main Body ECU

PROCEDURE

1.INSPECT ENGINE SWITCH
a.

Remove the engine switch (See page Engine / Hybrid System>2GR-FE STARTING>ENGINE SWITCH>REMOVAL).

U188268E01
5.914,1.548 6.295,1.713 0.381,0.165 10 SWIL 3.763,0.306 4.140,0.476 0.377,0.169 10 INDS 3.042,1.564 3.466,1.731 0.424,0.167 10 INDW 2.389,0.08 2.554,0.262 0.164,0.182 10 *b 1.546,1.381 1.701,1.556 0.155,0.175 10 *c 0.138,0.113 0.293,0.288 0.155,0.175 10 *a 4.878,0.306 5.248,0.472 0.369,0.165 10 COM 4.359,0.306 4.704,0.468 0.345,0.161 10 GND 4.076,0.476 4.421,1.23 false 4.534,0.472 4.449,0.92 false 5.017,0.472 4.694,0.92 false 3.477,1.617 4.097,1.386 false 5.862,1.617 4.792,1.386 false 1.619,1.056 1.619,1.35 false

Text in Illustration
*a Component without harness connected
(Engine Switch
*b Indicator Light
*c Illumination - -


b.

Apply battery voltage between the terminals of the switch, and check the illumination condition of the switch.

NOTICE:
·

If the positive (+) lead and the negative (-) lead are incorrectly connected, the engine switch indicator will not illuminate.

·

If the voltage is too low, the indicator will not illuminate.



OK:
Measurement Condition Specified Condition
Battery positive (+) → Terminal 11 (SWIL)
Battery negative (-) → Terminal 4 (COM) or 5 (GND)
Illuminates
Battery positive (+) → Terminal 12 (INDS)
Battery negative (-) → Terminal 4 (COM) or 5 (GND)
Illuminates
Battery positive (+) → Terminal 13 (INDW)
Battery negative (-) → Terminal 4 (COM) or 5 (GND)
Illuminates




OK

2.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE ENGINE SWITCH

2.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the G31 switch connector.


b.

Disconnect the G57 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
G31-11 (SWIL) - G57-25 (SWIL) Always Below 1 Ω
G31-12 (INDS) - G57-15 (INDS) Always Below 1 Ω
G31-13 (INDW) - G57-14 (INDW) Always Below 1 Ω
G31-5 (GND) - Body ground Always Below 1 Ω
G31-4 (COM) - Body ground Always Below 1 Ω
G31-11 (SWIL) or G57-25 (SWIL) - Body ground Always 10 kΩ or higher
G31-12 (INDS) or G57-15 (INDS) - Body ground Always 10 kΩ or higher
G31-13 (INDW) or G57-14 (INDW) - Body ground Always 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR