Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM C

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  B2278  Engine Switch Circuit Malfunction  


DESCRIPTION

This DTC is output when 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.

DTC No. DTC Detection Condition Trouble Area
B2278 Communication is abnormal between main body ECU and engine switch or engine switch is defective
·

Main body ECU

·

Engine switch

·

Wire harness



WIRING DIAGRAM

A126722E04
1.969,3.219 2.896,3.667 0.927,0.448 10 false G31 Engine Switch 5.094,3.979 6.135,4.542 1.042,0.563 10 false G57 Main Body ECU 2.802,1.865 3.115,2.052 0.313,0.188 10 false SS1 4.813,1.76 5.26,1.948 0.448,0.188 10 false SSW1 4.792,2.417 5.24,2.604 0.448,0.188 10 false SSW2 2.771,2.563 3.083,2.75 0.313,0.188 10 false SS2 1.708,2.542 2.052,2.719 0.344,0.177 10 false GND 4.448,2.26 4.646,2.479 0.198,0.219 10 false 16 4.448,1.594 4.698,1.823 0.25,0.229 10 false 17 3.188,1.615 3.365,1.792 0.177,0.177 10 false 7 3.156,2.271 3.406,2.479 0.25,0.208 10 false 2 1.49,2.292 1.688,2.531 0.198,0.24 10 false 5

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (START SWITCH 1 AND 2)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / Main Body ECU / Data List / St SW1 and St SW2.


d.

Read the value displayed on the tester.

Main body ECU
Item Measurement Item/Display (Range) Normal Condition Diagnostic Note
St SW1 Start Switch 1 / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-
St SW 2 Start Switch 2 / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-

OK:

ON appears on the screen.




OK

2.CHECK SWITCH CONDITION (ENGINE SWITCH)

NG

3.INSPECT ENGINE SWITCH
2.CHECK SWITCH CONDITION (ENGINE SWITCH)
a.

Ensure the electrical key is inside the cabin.


b.

Check that the power source mode changes as shown below each time the ignition switch is pushed.

OK:

off → on (ACC) → on (IG) → off




OK

SYSTEM IS OK

NG

3.INSPECT ENGINE SWITCH
A393973E01
0.552,1.125 0.833,1.125 true 0.563,1.625 1.385,1.167 true 2.802,1.344 2.271,1.135 true 0.24,1.052 0.677,1.313 0.438,0.26 10 false SS1 0.24,1.615 0.677,1.875 0.438,0.26 10 false GND 2.885,1.313 3.323,1.573 0.438,0.26 10 false SS2

a.

Remove the engine switch.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Switch Condition Specified Condition
7 (SS1) - 5 (GND) Pushed Below 1 Ω
2 (SS2) - 5 (GND) Pushed Below 1 Ω
7 (SS1) - 5 (GND) Not pushed 10 kΩ or higher
2 (SS2) - 5 (GND) Not pushed 10 kΩ or higher




OK

4.CHECK WIRE HARNESS (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE ENGINE SWITCH

4.CHECK WIRE HARNESS (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)
a.
A393997E03
0.5,1.417 0.917,1.667 0.417,0.25 0.5,3.667 0.917,3.917 0.417,0.25 1.833,1.594 2.479,1.281 false 2.167,1.635 2.469,1.635 false 0.917,1.906 1.385,1.667 false 2.167,3.958 2.563,4.26 false 2.271,3.948 2.583,3.802 false 0.198,0.146 1.615,0.5 1.417,0.354 10 false Wire Harness Side: 0.563,1.458 1.146,1.74 0.583,0.281 10 false G31 0.563,3.708 1.146,3.99 0.583,0.281 10 false G57 2.531,1.177 3.115,1.458 0.583,0.281 10 false GND 2.531,1.552 3.115,1.833 0.583,0.281 10 false SS1 0.563,1.854 1.146,2.135 0.583,0.281 10 false SS2 2.625,3.719 3.208,4 0.583,0.281 10 false SSW1 2.604,4.188 3.188,4.469 0.583,0.281 10 false SSW2 1.198,0.781 2.219,1.146 1.021,0.365 10 false Engine Switch 1.188,2.896 2.26,3.26 1.073,0.365 10 false Main Body ECU

Disconnect the G31 engine switch connector.


b.

Disconnect the G57 main body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G31-7 (SS1) - G57-17 (SSW1) Below 1 Ω
G31-2 (SS2) - G57-16 (SSW2) Below 1 Ω
G31-5 (GND) - Body ground Below 1 Ω
G31-7 (SS1) or G57-17 (SSW1) - Body ground 10 kΩ or higher
G31-2 (SS2) or G57-16 (SSW2) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR