Home › Engine / Hybrid System › 2AZ-FE STARTING › SMART ENTRY AND START SYSTEM
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292080 SMART ENTRY AND START SYSTEM J

2AZ-FE STARTING  SMART ENTRY AND START SYSTEM  Power Source Mode does not Change  


DESCRIPTION

When the certification ECU has detected the electrical key inside the cabin before the brake pedal is depressed, the power source mode can be changed in the following order sequentially by pressing the ignition switch: off → on (ACC) → on (IG) → off.

When one of the DTCs shown in the illustration below is detected, troubleshoot the DTC(s) by following the troubleshooting procedure relevant to the DTC(s). If the power source mode still cannot be changed normally, despite troubleshooting, one of the following may have occurred:

·

The LIN communication line is malfunctioning.

·

The certification ECU has determined that no key is inside the cabin.

·

The engine switch is malfunctioning.

·

The main body ECU is malfunctioning.


A393972E01
1.698,0.979 2.531,1.26 0.833,0.281 10 false AM2 NO. 2 0.177,1.135 1.073,1.438 0.896,0.302 10 false from Battery 1.146,3 1.781,3.271 0.635,0.271 10 false ACC 1.906,2.26 2.542,2.531 0.635,0.271 10 false IG2 2.323,1.479 3.302,1.76 0.979,0.281 10 false LH-IG Relay 1 0.208,4.406 3.531,4.698 3.323,0.292 10 false *: These DTCs are set when there is a malfunction 3.521,3.604 4.156,3.875 0.635,0.271 10 false ACCD 3.521,2.844 4.156,3.115 0.635,0.271 10 false IG2D 3.51,2.115 4.146,2.385 0.635,0.271 10 false IG1D 3.531,1.063 4.167,1.333 0.635,0.271 10 false AM1 3.531,1.24 4.167,1.51 0.635,0.271 10 false AM2 3.802,0.823 4.438,1.094 0.635,0.271 10 false B2271* 3.719,1.927 4.354,2.198 0.635,0.271 10 false B2272* 3.74,2.667 4.375,2.938 0.635,0.271 10 false B2273* 3.792,3.417 4.427,3.688 0.635,0.271 10 false B2274* 4.927,3.542 5.563,3.813 0.635,0.271 10 false GND2 4.906,1.063 5.542,1.333 0.635,0.271 10 false SSW1 4.906,1.25 5.542,1.521 0.635,0.271 10 false SSW2 4.719,0.833 5.354,1.104 0.635,0.271 10 false B2278* 6.104,1.677 7.104,1.99 1,0.313 10 false Engine Switch 3.896,0.219 5.052,0.552 1.156,0.333 10 false Main Body ECU 4.75,3.365 5.385,3.635 0.635,0.271 10 false B2271*

WIRING DIAGRAM

A394002E01
0.542,0.365 1.438,0.604 0.896,0.24 10 false from Battery 3.583,1.656 3.979,1.875 0.396,0.219 10 false 4D 4.823,1.667 5.219,1.885 0.396,0.219 10 false 5D 4.813,2.781 5.208,3 0.396,0.219 10 false 5M 3.583,2.375 3.979,2.594 0.396,0.219 10 false 4A 5.948,3.333 6.344,3.552 0.396,0.219 10 false ACC 3.531,3.771 3.927,3.99 0.396,0.219 10 false G57 3.521,4.781 3.917,5 0.396,0.219 10 false G58 2.365,0.938 2.76,1.156 0.396,0.219 10 false 4M 3.583,5.75 3.979,5.969 0.396,0.219 10 false 4A 4.823,3.781 5.219,4 0.396,0.219 10 false 5D 4.823,4.198 5.219,4.417 0.396,0.219 10 false 5D 4.833,4.604 5.229,4.823 0.396,0.219 10 false 5D 4.844,5.094 5.24,5.313 0.396,0.219 10 false 5A 3.521,4.188 3.917,4.406 0.396,0.219 10 false G57 0.885,3.938 1.281,4.156 0.396,0.219 10 false G57 0.885,5.469 1.281,5.688 0.396,0.219 10 false G57 0.865,6.063 1.26,6.281 0.396,0.219 10 false G57 0.875,4.542 1.271,4.76 0.396,0.219 10 false G58 4.802,1.479 5.198,1.698 0.396,0.219 10 false 12 3.583,1.458 3.979,1.677 0.396,0.219 10 false 11 2.708,0.938 3.104,1.156 0.396,0.219 10 false 1 3.625,2.177 4.021,2.396 0.396,0.219 10 false 5 3.615,3.563 4.01,3.781 0.396,0.219 10 false 3 3.573,4 3.969,4.219 0.396,0.219 10 false 22 4.875,3.563 5.271,3.781 0.396,0.219 10 false 7 4.875,3.99 5.271,4.208 0.396,0.219 10 false 3 4.844,4.417 5.24,4.635 0.396,0.219 10 false 27 4.875,4.875 5.271,5.094 0.396,0.219 10 false 4 3.583,5.563 3.979,5.781 0.396,0.219 10 false 26 0.958,3.719 1.354,3.938 0.396,0.219 10 false 6 0.917,5.854 1.313,6.073 0.396,0.219 10 false 16 0.938,5.26 1.333,5.479 0.396,0.219 10 false 17 5.594,6.573 5.99,6.792 0.396,0.219 10 false 2 1.792,6.531 2.906,6.771 1.115,0.24 10 false Main Body ECU 4.854,2.583 5.25,2.802 0.396,0.219 10 false 1 4.76,6.552 5.156,6.771 0.396,0.219 10 false 1 5.594,6.042 5.99,6.26 0.396,0.219 10 false 3 4.771,6.031 5.167,6.25 0.396,0.219 10 false 5 3.573,4.594 3.969,4.813 0.396,0.219 10 false 11 0.969,4.333 1.365,4.552 0.396,0.219 10 false 1 0.063,2.719 0.854,2.979 0.792,0.26 10 false AM2 NO. 2 1.844,2.688 2.802,3.01 0.958,0.323 10 false LH-IG Relay 1 1.802,3.292 2.708,3.552 0.906,0.26 10 false LH ECU-IG 1.25,3.927 2.042,4.188 0.792,0.26 10 false AM1 1.26,4.552 2.052,4.813 0.792,0.26 10 false AM2 1.25,5.479 2.042,5.74 0.792,0.26 10 false SSW1 1.24,6.063 2.031,6.323 0.792,0.26 10 false SSW2 2.188,5.771 2.979,6.031 0.792,0.26 10 false ACC 3.115,3.781 3.906,4.042 0.792,0.26 10 false IG1D 3.052,4.188 3.844,4.448 0.792,0.26 10 false ACCD 3.135,4.792 3.927,5.052 0.792,0.26 10 false IG2D 5.615,4.781 6.406,5.042 0.792,0.26 10 false ECU-ACC 5.188,5.375 6.781,5.792 1.594,0.417 10 false Instrument Panel Junction Block RH 5.135,6.719 5.927,6.979 0.792,0.26 10 false IG2 5.958,7.063 6.354,7.281 0.396,0.219 10 false 6 1.344,7.469 1.771,7.688 0.427,0.219 10 false SS2 1.344,7.948 1.771,8.167 0.427,0.219 10 false SS1 1.458,8.24 1.885,8.458 0.427,0.219 10 false G31 1.469,8.406 2.635,8.625 1.167,0.219 10 false Engine Switch 5.542,7.885 5.969,8.104 0.427,0.219 10 false G32 5.552,8.052 6.833,8.323 1.281,0.271 10 false Steering Lock ECU 6.021,7.354 6.448,7.573 0.427,0.219 10 false IG2 2.271,7.813 2.698,8.031 0.427,0.219 10 false GND 2.729,7.667 3.125,7.885 0.396,0.219 10 false 5 1.115,7.333 1.51,7.552 0.396,0.219 10 false 2 1.135,7.823 1.531,8.042 0.396,0.219 10 false 7

CAUTION / NOTICE / HINT

HINT:

If the vehicle is in key cancel mode, change to normal mode (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>CUSTOMIZE PARAMETERS).


PROCEDURE

1.CHECK WHETHER DTC OUTPUT RECURS
a.

Clear the DTCs.

HINT:

After all DTCs are cleared, check if the trouble occurs again 5 seconds after the ignition switch is turned on (IG).



b.

Check for DTCs again.

OK:

No DTC is output.




OK

2.CHECK BASIC FUNCTION

NG

2.CHECK BASIC FUNCTION
a.

Ensure the electrical key is inside the cabin.


b.

Check that the engine switch indicator illuminates in green when the shift lever is in P or N and the brake pedal is depressed.

OK:

Engine switch indicator illuminates in green.




OK

3.INSPECT FUSE (AM2 NO. 2)

NG

21.CHECK WIRELESS DOOR LOCK AND UNLOCK OPERATION
3.INSPECT FUSE (AM2 NO. 2)
a.

Remove the AM2 NO. 2 fuse from the No. 1 relay block.


b.

Check the fuse resistance.

Standard resistance:

Below 1 Ω




OK

4.READ VALUE USING INTELLIGENT TESTER (RELAY MONITOR)

NG

REPLACE FUSE

4.READ VALUE USING INTELLIGENT TESTER (RELAY MONITOR)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body / Main Body ECU / Data List / IG1 Relay Mon2, IG2 Relay Mon2 and ACC Relay Monitor.


d.

Read the display on the tester.

Main body ECU
Item Measurement Item / Display
(Range)
Normal Condition Diagnostic Note
IG1 Relay Mon1 LH-IG relay 1 outer relay monitor / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-
IG1 Relay Mon2 LH-IG relay 1 inner relay monitor / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-
IG2 Relay Mon1 IG2 outer relay monitor / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-
IG2 Relay Mon2 IG2 inner relay monitor / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-
ACC Relay Monitor ACC relay monitor / ON or OFF ON: Ignition switch on (IG)
OFF: Ignition switch off
-

OK:

ON is displayed on the tester screen.




NG

5.INSPECT IG2 RELAY

OK

REPLACE MAIN BODY ECU

5.INSPECT IG2 RELAY
a.
B426341E07
2.625,0.75 2.927,0.5 false 2.469,1.135 2.896,0.969 false 2.469,1.625 2.906,1.458 false 2.031,0.708 1.719,0.469 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 2 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.323 1.396,1.542 0.219,0.219 10 false 1 1.563,0.354 1.781,0.573 0.219,0.219 10 false 1 2.99,0.875 3.208,1.094 0.219,0.219 10 false 5 2.979,1.375 3.198,1.594 0.219,0.219 10 false 3 2.969,0.417 3.188,0.635 0.219,0.219 10 false 2

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(When battery voltage is applied to terminals 1 and 2)




OK

6.CHECK LH-IG RELAY 1 CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)

NG

REPLACE RELAY (IG2)

6.CHECK LH-IG RELAY 1 CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.
U188711E02
1.573,1.573 0.583,2.052 false 0.104,0.052 1.823,0.219 1.719,0.167 10 false Wire Harness Side: 1.542,0.656 1.865,0.823 0.323,0.167 10 false G57 1.271,2.281 2.292,2.427 1.021,0.146 10 false Main Body ECU 0.385,2.063 0.729,2.219 0.344,0.156 10 false IG1D 1.49,2.906 1.698,3.073 0.208,0.167 10 false 5D 0.656,4.198 2.906,4.365 2.25,0.167 10 false Instrument Panel Junction Block RH

Disconnect the G57 main body ECU connector.


b.

Disconnect the 5D instrument panel junction block RH connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G57-3 (IG1D) - 5D-7 10 kΩ or higher
G57-3 (IG1D) or 5D-7 - Body ground Below 1 Ω
(When battery voltage is applied to terminals 1 and 2)




OK

7.CHECK LH-IG RELAY 1 CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK LH-IG RELAY 1 CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.
U188572E02
0.104,0.021 1.771,0.219 1.667,0.198 10 false Wire Harness Side: 1.646,1.313 1.885,1.49 0.24,0.177 10 false 5D

Disconnect the 5D instrument panel junction block RH connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
5D-7 - Body ground Ignition switch on (IG) 10 to 14 V




OK

8.CHECK LH-IG RELAY 1 CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - MAIN BODY ECU)

NG

REPLACE MAIN BODY ECU

8.CHECK LH-IG RELAY 1 CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - MAIN BODY ECU)
a.
U188395E02
0.146,0.083 1.938,0.25 1.792,0.167 10 false Wire Harness Side: 0.667,2.271 2.948,2.427 2.281,0.156 10 false Instrument Panel Junction Block RH 1.51,0.938 1.708,1.104 0.198,0.167 10 false 5D 1.573,2.76 1.771,2.927 0.198,0.167 10 false 4D 1.219,4.073 2.323,4.229 1.104,0.156 10 false Main Body ECU

Disconnect the 5D instrument panel junction block RH connector.


b.

Disconnect the 4D main body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
5D-7 - 4D-11 Below 1 Ω
5D-7 or 4D-11 - Body ground 10 kΩ or higher




OK

9.CHECK LH-IG RELAY 1 CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK LH-IG RELAY 1 CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - MAIN BODY ECU)
a.
U188571E02
0.104,0.063 1.979,0.24 1.875,0.177 10 false Wire Harness Side: 1.604,1.229 1.813,1.406 0.208,0.177 10 false 4D

Disconnect the 4D main body ECU connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
4D-11 - Body ground Ignition switch on (IG) 10 to 14 V




OK

10.CHECK LH-IG RELAY 1 CIRCUIT (MAIN BODY ECU - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

10.CHECK LH-IG RELAY 1 CIRCUIT (MAIN BODY ECU - BODY GROUND)
a.
U188580E02
0.063,0.135 1.708,0.354 1.646,0.219 10 false Wire Harness Side: 1.542,1.292 1.781,1.5 0.24,0.208 10 false 4A

Disconnect the 4A main body ECU connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
4A-5 - Body ground Below 1 Ω




OK

11.CHECK LH-IG RELAY 1 CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK LH-IG RELAY 1 CIRCUIT
a.
A135949E01
0.367,0.135 1.738,0.453 1.371,0.317 10 Main Body ECU: 0.794,2.55 2.762,2.765 1.968,0.215 10 LH ECU-IG Fuse Positive Side 1.375,1.925 1.375,2.456 false 1.349,1.904 1.411,1.948 0.062,0.044

Remove the LH ECU-IG fuse from the main body ECU.


b.

Measure the voltage of the main body ECU.

Standard voltage:
Tester Connection Condition Specified Condition
LH ECU-IG fuse positive side of main body ECU - Body ground Ignition switch on (IG) 10 to 14 V




OK

12.CHECK ACC RELAY CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)

NG

REPLACE MAIN BODY ECU

12.CHECK ACC RELAY CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.
U188712E02
1.813,1.948 2.667,1.375 false 0.125,0.073 1.677,0.24 1.552,0.167 10 false Wire Harness Side: 1.24,2.281 2.26,2.448 1.021,0.167 10 false Main Body ECU 1.563,0.615 1.844,0.76 0.281,0.146 10 false G57 2.729,1.26 3.146,1.417 0.417,0.156 10 false ACCD 1.552,2.792 1.771,2.938 0.219,0.146 10 false 5D 0.542,4.208 2.792,4.375 2.25,0.167 10 false Instrument Panel Junction Block RH

Disconnect the G57 main body ECU connector.


b.

Disconnect the 5D instrument panel junction block RH connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G57-22 (ACCD) - 5D-3 Below 1 Ω
G57-22 (ACCD) or 5D-3 - Body ground 10 kΩ or higher




OK

13.CHECK ACC RELAY CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK ACC RELAY CIRCUIT (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.
U188573E02
0.188,0.083 1.75,0.271 1.563,0.188 10 false Wire Harness Side: 1.552,1.25 1.771,1.406 0.219,0.156 10 false 5D

Disconnect the 5D instrument panel junction block RH connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
5D-3 - Body ground Ignition switch on (ACC) 10 to 14 V




OK

14.CHECK ACC RELAY CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - BODY GROUND)

NG

REPLACE MAIN BODY ECU

14.CHECK ACC RELAY CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - BODY GROUND)
a.
U188581E02
0.146,0.052 1.677,0.26 1.531,0.208 10 false Wire Harness Side: 1.677,1.219 1.885,1.385 0.208,0.167 10 false 5A

Disconnect the 5A instrument panel junction block RH connector.


b.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Specified Condition
5A-4 - Body ground Below 1 Ω




OK

15.CHECK ACC RELAY CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK ACC RELAY CIRCUIT (INSTRUMENT PANEL JUNCTION BLOCK RH - BATTERY)
a.
U188575E02
0.094,0.042 1.729,0.198 1.635,0.156 10 false Wire Harness Side: 1.583,1.01 1.823,1.167 0.24,0.156 10 false 5M

Disconnect the 5M instrument panel junction block RH connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Specified Condition
5M-1 - Body ground 10 to 14 V




OK

16.CHECK ACC RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK ACC RELAY
a.
U188573E02
0.188,0.083 1.75,0.271 1.563,0.188 10 false Wire Harness Side: 1.552,1.25 1.771,1.406 0.219,0.156 10 false 5D

Disconnect the 5D instrument panel junction block RH connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
5D-27 - Body ground Ignition switch on (ACC) 10 to 14 V




OK

17.CHECK WIRE HARNESS (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

17.CHECK WIRE HARNESS (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)
U188399E01
0.116,0.045 1.478,0.335 1.362,0.290 10 Wire Harness Side: 1.139,0.856 1.871,1.158 0.732,0.302 10 IG2 Relay 3.43,3.198 5.530,3.382 2.100,0.184 10 Engine Room No. 1 Relay Block 1.931,3.084 3.022,3.333 1.091,0.248 10 Main Body ECU 2.3,1.926 2.706,2.166 0.406,0.239 10 G58 0.955,2.582 1.305,2.773 0.350,0.191 10 IG2D 2.1,2.77 1.354,2.652 false

a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Disconnect the G58 main body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
Relay block IG2 relay terminal 1 - G58-11 (IG2D) Below 1 Ω
Relay block IG2 relay terminal 2 - Body ground Below 1 Ω
Relay block IG2 relay terminal 1 or G58-11 (IG2D) - Body ground 10 kΩ or higher
Relay block IG2 relay terminal 2 - Body ground Below 1 Ω




OK

18.CHECK WIRE HARNESS (IG2 RELAY - STEERING LOCK ECU AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK WIRE HARNESS (IG2 RELAY - STEERING LOCK ECU AND BATTERY)
U188400E02
2.427,2.917 2.813,2.75 false 0.104,0.042 1.573,0.281 1.469,0.24 10 false Wire Harness Side: 3.438,3.25 5.542,3.469 2.104,0.219 10 false Engine Room No. 1 Relay Block 1.188,0.813 1.885,1.094 0.698,0.281 10 false IG2 Relay 1.583,3.302 2.823,3.604 1.24,0.302 10 false Steering Lock ECU 2.042,2.156 2.469,2.417 0.427,0.26 10 false G32 2.854,2.635 3.5,2.885 0.646,0.25 10 false IG2

a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Disconnect the G32 steering lock ECU connector.


c.

Measure the voltage and resistance of the wire harness side connectors.

Standard voltage:
Tester Connection Specified Condition
Relay block IG2 terminal 5 - Body ground 10 to 14 V


Standard resistance:
Tester Connection Specified Condition
Relay block IG2 terminal 3 - G32-6 (IG2) Below 1 Ω




OK

19.INSPECT ENGINE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT ENGINE SWITCH
a.
A393973E01
0.552,1.125 0.833,1.125 true 0.563,1.625 1.385,1.167 true 2.802,1.344 2.271,1.135 true 0.24,1.052 0.677,1.313 0.438,0.26 10 false SS1 0.24,1.615 0.677,1.875 0.438,0.26 10 false GND 2.885,1.313 3.323,1.573 0.438,0.26 10 false SS2

Remove the engine switch.


b.

Measure the resistance of the switch.

Standard resistance:
Tester Connection Condition Specified Condition
7 (SS1) - 5 (GND) Pushed Below 1 Ω
2 (SS2) - 5 (GND) Pushed Below 1 Ω
7 (SS1) - 5 (GND) Not pushed 10 kΩ or higher
2 (SS2) - 5 (GND) Not pushed 10 kΩ or higher




OK

20.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY AND BODY GROUND)

NG

REPLACE ENGINE SWITCH

20.CHECK WIRE HARNESS (MAIN BODY ECU - BATTERY AND BODY GROUND)
U188707E02
1.594,1.365 1.313,2.229 false 2.615,1.396 2.719,2.219 false 5.031,1.479 4.948,2.167 false 0.146,0.063 1.479,0.333 1.333,0.271 10 false Wire Harness Side: 1.063,0.573 1.51,0.854 0.448,0.281 10 false G57 2.927,0.573 3.375,0.854 0.448,0.281 10 false G58 5.615,0.573 6.063,0.854 0.448,0.281 10 false 4A 1.146,2.25 1.625,2.438 0.479,0.188 10 false AM1 2.646,2.271 3.146,2.458 0.5,0.188 10 false AM2 4.677,2.208 5.271,2.448 0.594,0.24 10 false GND2

a.

Disconnect the 4A, G57 and G58 main body ECU connectors.


b.

Measure the voltage and resistance of the wire harness side connectors.

Standard voltage:
Tester Connection Specified Condition
G57-6 (AM1) - Body ground 10 to 14 V
G58-1 (AM2) - Body ground 10 to 14 V


Standard resistance:
Tester Connection Specified Condition
4A-3 (GND2) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK WIRELESS DOOR LOCK AND UNLOCK OPERATION
a.

Check that the wireless door lock and unlock functions operate normally.

OK:

Wireless door lock and unlock functions operate normally.




OK

22.CHECK OPERATION OF ELECTRICAL KEY

NG

22.CHECK OPERATION OF ELECTRICAL KEY
a.

After replacing the electrical key with a normally functioning one, check that the wireless door lock and unlock functions operate normally.

OK:

Wireless door lock and unlock functions operate normally.




NG

23.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDOOR ELECTRICAL KEY OSCILLATOR)

OK

END (ELECTRICAL KEY IS DEFECTIVE)

23.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INDOOR ELECTRICAL KEY OSCILLATOR)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check that the oscillator operates.

Certification ECU
Item Test Details Diagnostic Note
Fr Transmitter Indoor electrical key oscillator (front)
ON / OFF
-

OK:

Indoor electrical key oscillator is ON.




NG

24.CHECK INDOOR ELECTRICAL KEY OSCILLATOR

OK

GO TO ROOM OSCILLATOR DOES NOT RECOGNIZE KEY (DOOR LOCK SECTION)

24.CHECK INDOOR ELECTRICAL KEY OSCILLATOR
a.

Ensure the electrical key is inside the cabin.


b.

Replace the indoor electrical key oscillator with a new one.


c.

Depress the brake pedal with the shift lever in P or N and check that the engine switch indicator illuminates in green.



OK

END (INDOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU