Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START C

2AZ-FE STARTING  PUSH-BUTTON START  B2273  Ignition 2 Monitor Malfunction  


DESCRIPTION

This DTC is output when a malfunction occurs in the IG2D output circuit, which is between the IG2 relay actuation circuit inside the main body ECU and the IG2 relay.

DTC No. DTC Detection Condition Trouble Area
B2273 IG2 relay actuation circuit inside main body ECU or other related circuit is malfunctioning
·

Main body ECU


·

IG2 relay


·

Wire harness



WIRING DIAGRAM

A126720E04
0.385,1.302 0.906,1.667 0.521,0.365 10 false from Battery 0.073,2.26 1.104,2.583 1.031,0.323 10 false to Steering Lock ECU 2.885,1.552 3.198,1.719 0.313,0.167 10 false IG2 2.906,3.25 3.219,3.417 0.313,0.167 10 false IG2 5.865,2.917 6.26,3.083 0.396,0.167 10 false IG2D 5.833,3.698 6.917,4.063 1.083,0.365 10 false G58 Main Body ECU 5.531,2.802 5.729,3.021 0.198,0.219 10 false 11 2.479,2.208 2.635,2.396 0.156,0.188 10 false 3 2.49,2.781 2.74,3.042 0.25,0.26 10 false 2 3.385,2.198 3.635,2.365 0.25,0.167 10 false 5 3.375,2.802 3.583,2.969 0.208,0.167 10 false 1

PROCEDURE

1.READ VALUE USING GTS (IG2 RELAY MONITOR (INSIDE))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / IG2 Relay Mon2.


d.

Read the display on the tester.

Main body ECU:
Item Measurement Item / Display (Range) Normal Condition Diagnostic Note
IG2 Relay Monitor(Inside) IG2 inner relay monitor / ON or OFF ON: Engine switch on (IG)
OFF: Engine switch off
-


OK:

When the engine switch is turned on (IG), ON is displayed on the tester.




OK

2.CHECK SWITCH CONDITION (ENGINE SWITCH)

NG

3.INSPECT IG2 RELAY
2.CHECK SWITCH CONDITION (ENGINE SWITCH)
a.

Ensure the electrical key is inside the cabin.


b.

Check that the power source mode changes as shown below each time the engine switch is pushed.

OK:

off → on (ACC) → on (IG) → off




OK

NORMAL

NG

3.INSPECT IG2 RELAY
a.

Remove the IG2 relay from the engine room No. 1 relay block.


B426341E08
2.625,0.75 2.927,0.5 false 2.469,1.135 2.896,0.969 false 2.469,1.625 2.906,1.458 false 2.031,0.708 1.719,0.469 false 0.24,0.76 0.458,0.979 0.219,0.219 10 false 3 0.229,1.323 0.448,1.542 0.219,0.219 10 false 2 1.198,0.76 1.417,0.979 0.219,0.219 10 false 5 1.177,1.323 1.396,1.542 0.219,0.219 10 false 1 1.563,0.354 1.781,0.573 0.219,0.219 10 false 1 2.99,0.875 3.208,1.094 0.219,0.219 10 false 5 2.979,1.375 3.198,1.594 0.219,0.219 10 false 3 2.969,0.417 3.188,0.635 0.219,0.219 10 false 2

b.

Measure the resistance of the relay.

Standard resistance:
Tester Connection Specified Condition
3 - 5 10 kΩ or higher
3 - 5 Below 1 Ω
(when battery voltage is applied to terminals 1 and 2)




OK

4.CHECK WIRE HARNESS (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE IG2 RELAY

4.CHECK WIRE HARNESS (IG2 RELAY - MAIN BODY ECU AND BODY GROUND)
a.

Remove the IG2 relay from the engine room No. 1 relay block.


b.

Disconnect the G58 main body ECU connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
Relay block IG2 relay terminal 1 - G58-11 (IG2D) Below 1 Ω
Relay block IG2 relay terminal 2 - Body ground Below 1 Ω
Relay block IG2 relay terminal 1 or G58-11 (IG2D) - Body ground 10 kΩ or higher




OK

REPLACE MAIN BODY ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR