When the certification ECU has detected the electrical key inside the cabin before the brake pedal is depressed, the power source mode can be changed in the following order sequentially by pressing the engine switch: off → on (ACC) → on (IG) → off.
When one of the DTCs shown in the illustration below is detected, troubleshoot the DTC(s) by following the troubleshooting procedure relevant to the DTC(s). If the power source mode still cannot be changed normally, despite troubleshooting, one of the following may have occurred:
The LIN communication line is malfunctioning.
The certification ECU has determined that no key is inside the cabin.
The engine switch is malfunctioning.
The main body ECU is malfunctioning.
If the vehicle is in key cancel mode, change to normal mode (see page Vehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>CUSTOMIZE PARAMETERS).
Clear the DTCs.
After all DTCs are cleared, check if the trouble occurs again 5 seconds after the engine switch is turned on (IG).
Check for DTCs again.
No DTC is output.
OK
NG
Ensure the electrical key is inside the cabin.
Check that the engine switch indicator illuminates in green when the shift lever is in P or N and the brake pedal is depressed.
Engine switch indicator illuminates in green.
OK
NG
Remove the AM2 NO. 2 fuse from the No. 1 relay block.
Check the fuse resistance.
Below 1 Ω
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and turn the tester ON.
Select the following menu items: Body Electrical / Main Body ECU / Data List / IG1 Relay Mon2, IG2 Relay Mon2 and ACC Relay Monitor.
Read the display on the tester.
| Item | Measurement Item / Display
(Range) |
Normal Condition | Diagnostic Note |
|---|---|---|---|
| IG1 Relay Monitor(Outside) | LH-IG relay 1 outer relay monitor / ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
- |
| IG1 Relay Monitor(Inside) | LH-IG relay 1 inner relay monitor / ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
- |
| IG2 Relay Monitor(Outside) | IG2 outer relay monitor / ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
- |
| IG2 Relay Monitor(Inside) | IG2 inner relay monitor / ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
- |
| ACC Relay Monitor | ACC relay monitor / ON or OFF | ON: Engine switch on (IG)
OFF: Engine switch off |
- |
ON is displayed on the tester screen.
NG
OK
Remove the IG2 relay from the engine room No. 1 relay block.
Measure the resistance of the relay.
| Tester Connection | Specified Condition |
|---|---|
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω
(When battery voltage is applied to terminals 1 and 2) |
OK
NG
Disconnect the G57 main body ECU connector.
Disconnect the 5D instrument panel junction block RH connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G57-3 (IG1D) - 5D-7 | 10 kΩ or higher |
| G57-3 (IG1D) or 5D-7 - Body ground | Below 1 Ω
(When battery voltage is applied to terminals 1 and 2) |
OK
NG
Disconnect the 5D instrument panel junction block RH connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5D-7 - Body ground | Engine switch on (IG) | 10 to 14 V |
OK
NG
Disconnect the 5D instrument panel junction block RH connector.
Disconnect the 4D main body ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| 5D-7 - 4D-11 | Below 1 Ω |
| 5D-7 or 4D-11 - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the 4D main body ECU connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4D-11 - Body ground | Engine switch on (IG) | 10 to 14 V |
OK
NG
Disconnect the 4A main body ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| 4A-5 - Body ground | Below 1 Ω |
OK
NG
Remove the LH ECU-IG fuse from the main body ECU.
Measure the voltage of the main body ECU.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ECU-IG fuse positive side of main body ECU - Body ground | Engine switch on (IG) | 10 to 14 V |
OK
NG
Disconnect the G57 main body ECU connector.
Disconnect the 5D instrument panel junction block RH connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G57-22 (ACCD) - 5D-3 | Below 1 Ω |
| G57-22 (ACCD) or 5D-3 - Body ground | 10 kΩ or higher |
OK
NG
Disconnect the 5D instrument panel junction block RH connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5D-3 - Body ground | Engine switch on (ACC) | 10 to 14 V |
OK
NG
Disconnect the 5A instrument panel junction block RH connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| 5A-4 - Body ground | Below 1 Ω |
OK
NG
Disconnect the 5M instrument panel junction block RH connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| 5M-1 - Body ground | 10 to 14 V |
OK
NG
Disconnect the 5D instrument panel junction block RH connector.
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5D-27 - Body ground | Engine switch on (ACC) | 10 to 14 V |
OK
NG
Remove the IG2 relay from the engine room No. 1 relay block.
Disconnect the G58 main body ECU connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| Relay block IG2 relay terminal 1 - G58-11 (IG2D) | Below 1 Ω |
| Relay block IG2 relay terminal 2 - Body ground | Below 1 Ω |
| Relay block IG2 relay terminal 1 or G58-11 (IG2D) - Body ground | 10 kΩ or higher |
| Relay block IG2 relay terminal 2 - Body ground | Below 1 Ω |
OK
NG
Remove the IG2 relay from the engine room No. 1 relay block.
Disconnect the G32 steering lock ECU connector.
Measure the voltage and resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| Relay block IG2 terminal 5 - Body ground | 10 to 14 V |
| Tester Connection | Specified Condition |
|---|---|
| Relay block IG2 terminal 3 - G32-6 (IG2) | Below 1 Ω |
OK
NG
Remove the engine switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (SS1) - 5 (GND) | Pushed | Below 1 Ω |
| 2 (SS2) - 5 (GND) | Pushed | Below 1 Ω |
| 7 (SS1) - 5 (GND) | Not pushed | 10 kΩ or higher |
| 2 (SS2) - 5 (GND) | Not pushed | 10 kΩ or higher |
| *a | Component without harness connected
(Engine Switch) |
OK
NG
Disconnect the 4A, G57 and G58 main body ECU connectors.
Measure the voltage and resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G57-6 (AM1) - Body ground | 10 to 14 V |
| G58-1 (AM2) - Body ground | 10 to 14 V |
| Tester Connection | Specified Condition |
|---|---|
| 4A-3 (GND2) - Body ground | 10 kΩ or higher |
OK
NG
Check that the wireless door lock and unlock functions operate normally.
Wireless door lock and unlock functions operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
After replacing the electrical key with a normally functioning one, check that the wireless door lock and unlock functions operate normally.
Wireless door lock and unlock functions operate normally.
NG
OK
Select the Active Test, use the GTS to generate a control command, and then check that the oscillator operates.
| Item | Test Details | Diagnostic Note |
|---|---|---|
| Fr-Seat Inside Transmitter | Indoor electrical key oscillator (front)
ON / OFF |
- |
Indoor electrical key oscillator is ON.
NG
OK
(See pageVehicle Interior>DOOR LOCK>SMART ENTRY AND START SYSTEM>Room Oscillator does not Recognize Key)
Ensure the electrical key is inside the cabin.
Replace the indoor electrical key oscillator with a new one.
Depress the brake pedal with the shift lever in P or N and check that the engine switch indicator illuminates in green.
OK
NG