Home › Engine / Hybrid System › 2AZ-FE STARTING › PUSH-BUTTON START
RM24M0E _51 Engine / Hybrid System _059575 2AZ-FE STARTING _0292081 PUSH-BUTTON START C

2AZ-FE STARTING  PUSH-BUTTON START  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is output when a malfunction occurs in the ACCD output circuit, which is between the ACC relay actuation circuit inside the main body ECU and the ACC relay.

DTC No. DTC Detection Condition Trouble Area
B2274 ACC relay actuation circuit inside main body ECU or other related circuit is malfunctioning
·

Main body ECU

·

Instrument panel junction block RH (ACC relay)

·

Wire harness



WIRING DIAGRAM

A135934E03
1,4.396 2.354,4.646 1.354,0.25 10 false Main Body ECU 5.156,1.958 5.99,2.135 0.833,0.177 10 false ECU-ACC 0.948,3.01 1.469,3.302 0.521,0.292 10 false ACC 2.24,3.375 2.708,3.573 0.469,0.198 10 false ACCD 2.188,0.885 3.052,1.156 0.865,0.271 10 false from Battery 4.615,4.344 6.938,4.635 2.323,0.292 10 false Instrument Panel Junction Block RH 5.542,3.688 5.938,3.917 0.396,0.229 10 false ACC 2.719,3.344 3.021,3.563 0.302,0.219 10 false G57 2.771,1.802 3.01,2 0.24,0.198 10 false 4A 2.781,3.135 3,3.313 0.219,0.177 10 false 22 2.792,1.583 2.979,1.74 0.188,0.156 10 false 26 4.406,1.792 4.615,2.021 0.208,0.229 10 false 5D 4.417,1.604 4.604,1.771 0.188,0.167 10 false 27 4.406,2.802 4.646,2.99 0.24,0.188 10 false 5M 4.406,3.333 4.625,3.521 0.219,0.188 10 false 5D 4.406,3.969 4.604,4.146 0.198,0.177 10 false 5A 4.448,3.781 4.563,3.927 0.115,0.146 10 false 4 4.448,3.135 4.573,3.281 0.125,0.146 10 false 3 4.448,2.583 4.583,2.74 0.135,0.156 10 false 1

PROCEDURE

1.READ VALUE USING GTS (ACC RELAY MONITOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester ON.


c.

Select the following menu items: Body Electrical / Main Body ECU / Data List / ACC Relay Mon.


d.

Read the display on the tester.

Main body ECU
Item Measurement Item / Display
(Range)
Normal Condition Diagnostic Note
ACC Relay Monitor ACC relay monitor / ON or OFF ON: Engine switch on (ACC)
OFF: Engine switch off
-

OK:

When the engine switch is turned on (ACC), ON is displayed on the tester.




OK

2.CHECK SWITCH CONDITION (ENGINE SWITCH)

NG

3.CHECK WIRE HARNESS (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
2.CHECK SWITCH CONDITION (ENGINE SWITCH)
a.

Ensure the electrical key is inside the cabin.


b.

Check that the power source mode changes as shown below each time the engine switch is pushed.

OK:

off → on (ACC) → on (IG) → off




OK

NORMAL

NG

3.CHECK WIRE HARNESS (MAIN BODY ECU - INSTRUMENT PANEL JUNCTION BLOCK RH)
a.

Disconnect the G57 main body ECU connector.


b.

Disconnect the 5D instrument panel junction block RH connector.


c.

Measure the resistance of the wire harness side connectors.

Standard resistance:
Tester Connection Specified Condition
G57-22 (ACCD) - 5D-3 Below 1 Ω
G57-22 (ACCD) or 5D-3 - Body ground 10 kΩ or higher




OK

4.CHECK MAIN BODY ECU OPERATION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK MAIN BODY ECU OPERATION
a.

Disconnect the 5D instrument panel junction block RH connector.


b.

Measure the voltage of the wire harness side connector.

Standard voltage:
Tester Connection Condition Specified Condition
5D-3 - Body ground Engine switch on (ACC) 10 to 14 V




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK RH

NG

REPLACE MAIN BODY ECU