Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0746  Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)  


DESCRIPTION

The ECM uses signals from the vehicle speed sensor to detect the actual gear position (1st, 2nd, 3rd or O/D gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems of the shift solenoid valves, valve body or automatic transaxle (clutch, brake, gear, etc.).

DTC No. DTC Detection Condition Trouble Area
P0746 Gear required by the ECM does not match the actual gear when driving (2 trip detection logic)
·

Shift solenoid valve SL1 remains open or closed

·

Valve body is blocked

·

Shift solenoid valve SL1

·

Automatic transaxle (clutch, brake, gear, etc.)

·

ECM



MONITOR DESCRIPTION

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. According to the input shaft revolution, intermediate (counter) shaft revolution and output shaft revolution, the ECM detects the actual gear position (1st, 2nd, 3rd or O/D gear position). When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL.

Example:

When either condition (a) or (b) is met, the ECM detects a malfunction.

(a) The ECM commands the 1st gear, but the actual gear is 2nd.

(b) The ECM commands the 2nd gear, but the actual gear is 1st.

CAUTION / NOTICE / HINT

HINT:

Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.

The Data List can be displayed during the Active Test.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch on (IG) and turn the tester ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test.

6.

Follow the instructions on the tester and perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the tester. Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART).


ECM:
Item Test Details Diagnostic Note
Control the shift position [Test Details]
Operate shift solenoid valve and set each shift lever position manually
[Vehicle Condition]
·

IDL: ON

·

50 km/h (31 mph) or less


[Other information]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of shift solenoid valves

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or more.

·

This shift position commanded by the ECM is shown in the Data List (shift status) display on the tester.




PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0746)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC / Current or Pending.


d.

Read the DTCs using the tester.

Result:
Display (DTC output) Proceed to
Only P0746 is output A
P0746 and other DTCs are output B



HINT:

If any other codes besides P0746 are output, perform troubleshooting for those DTCs first.



A

2.INSPECT SHIFT SOLENOID VALVE SL1

B

GO TO DTC CHART

2.INSPECT SHIFT SOLENOID VALVE SL1
C140848E08
1.021,0.479 1.479,0.938 false 2.24,0.49 1.781,0.948 false 1.031,2.604 1.49,3.073 false 2.24,2.594 1.781,3.063 false 0.906,0.375 1.198,0.583 0.292,0.208 10 false 1 2.281,0.365 2.5,0.563 0.219,0.198 10 false 2 0.917,2.5 1.208,2.708 0.292,0.208 10 false 1 2.281,2.479 2.5,2.677 0.219,0.198 10 false 2 1.208,4.104 1.604,4.354 0.396,0.25 10 false (-) 1.917,4.104 2.281,4.313 0.365,0.208 10 false (+)

a.

Remove the shift solenoid valve SL1.


b.

Measure the resistance of the solenoid valve.

Standard resistance:

5.0 to 5.6 Ω at 20°C (68°F)



c.

Connect the battery's positive (+) lead with a 21 W bulb to terminal 2 and the negative (-) lead to terminal 1 of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes operating noise.




OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

REPLACE SHIFT SOLENOID VALVE SL1

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

OK:

There are no foreign objects on each valve.




OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION).

OK:

The torque converter assembly operates normally.




OK

REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

REPLACE TORQUE CONVERTER ASSEMBLY