Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292096 AUTOMATIC TRANSAXLE SYSTEM C

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0741  Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve DSL)  


DESCRIPTION

The ECM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, intermediate (counter) shaft speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

Then the ECM compares the engagement conditions of the lock-up clutch with the lock-up schedule in the ECM memory to detect mechanical problems of the shift solenoid valve DSL, valve body and torque converter assembly.

DTC No. DTC Detection Condition Trouble Area
P0741 Lock-up does not occur when driving in lock-up range
Lock-up remains ON in lock-up OFF range
(2 trip detection logic)
·

Shift solenoid valve DSL remains open or closed

·

Valve body is blocked

·

Torque converter assembly

·

Automatic transaxle (clutch, brake, gear, etc.)

·

Line pressure is too low



MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on the speed sensor (NT), speed sensor (NC), engine rpm, engine load, engine temperature, vehicle speed, transmission temperature and gear selection.

The ECM determines the lock-up status of the torque converter assembly by comparing the engine rpm (NE) to the input turbine rpm (NT). The ECM calculates the actual transmission gear by comparing the input turbine rpm control voltage to the counter gear rpm (NC). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to the shift solenoid valve DSL. When the DSL is turned on, it applies pressure to the lock-up relay valve and locks the torque converter assembly.

If the ECM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the ECM interprets this as a fault in the shift solenoid valve DSL or lock-up system performance.

The ECM will illuminate the MIL and store the DTC.

HINT:
Example:

When either of the following conditions is met, the system judges it as a malfunction.


·

There is a difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up.

(Engine speed is at least 100 rpm greater than input turbine speed.)

·

There is no difference in rotation between the input side (engine speed) and output side (input turbine speed) of the torque converter when the ECM commands lock-up off.

(The difference between engine speed and input turbine speed is less than 35 rpm.)


WIRING DIAGRAM

C142136E01
6.041,2.775 6.438,2.956 0.397,0.182 10 ECM 5.86,1.682 6.256,1.863 0.397,0.182 10 DSL 5.537,1.457 5.933,1.639 0.397,0.182 10 79 2.686,1.787 3.082,1.968 0.397,0.182 10 3 2.243,1.787 2.639,1.968 0.397,0.182 10 DSL 0.789,2.769 2.417,3.092 1.628,0.323 10 Shift Solenoid Valve DSL (ECT Solenoid) 5.537,1.682 5.933,1.863 0.397,0.182 10 D2 0.789,2.588 2.417,2.760 1.628,0.172 10 D51

CAUTION / NOTICE / HINT

HINT:

Performing the intelligent tester's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.

The Data List can be displayed during the Active Test.


1.

Warm up the engine.

2.

Turn the ignition switch off.

3.

Connect the intelligent tester to the DLC3.

4.

Turn the ignition switch on (IG) and turn the tester ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test.

6.

Follow the instructions on the tester and perform the Active Test.

ECM:
Item Test Details Diagnostic Note
Activate the Lock Up [Test Details]
Control shift solenoid DSL to set automatic transaxle to the lock-up condition
[Vehicle Condition]
·

Throttle valve opening angle: Less than 35%

·

Vehicle speed: 58 km/h (36 mph) or more


Possible to check shift solenoid valve DSL operation

HINT:
·

This test can be conducted when the vehicle speed is 58 km/h (36 mph) or more.

·

This test can be conducted in the O/D gear.



7.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is ON.

·

Slowly release the accelerator pedal in order to decelerate. (Do not fully release the pedal as that will close the throttle valve and lock-up may be turned OFF.)




C122107E08
4.729,2.146 5.365,1.615 false 4.74,2.271 5.365,2.104 false 0.646,0.583 1.823,0.823 1.177,0.24 10 false Throttle Position 5.406,1.521 6.271,1.771 0.865,0.25 10 false Lock-up ON 5.417,2.01 6.375,2.25 0.958,0.24 10 false Lock-up OFF 0.792,1.875 1.688,2.115 0.896,0.24 10 false Engine rpm 4.604,1.188 5.052,1.427 0.448,0.24 10 false Time 4.573,2.469 5.021,2.708 0.448,0.24 10 false Time 2.052,0.281 2.51,0.521 0.458,0.24 10 false 100% 2.208,0.917 2.531,1.156 0.323,0.24 10 false 0% 2.031,2.365 2.521,2.604 0.49,0.24 10 false 0 rpm

PROCEDURE

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0741)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch on (IG) and turn the tester ON.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC / Current or Pending.


d.

Read the DTCs using the tester.

Result:
Display (DTC output) Proceed to
Only P0741 is output A
P0741 and other DTCs are output B


HINT:

If any other codes besides P0741 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DSL)

B

GO TO DTC CHART

2.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE DSL)
C141259E12
1.729,0.979 1.875,0.521 false 1.771,0.354 2.135,0.552 0.365,0.198 10 false DSL

a.

Disconnect the D51 wire connector.


b.

Measure the resistance of the transmission wire.

Standard resistance:
Tester Connection Condition Specified Condition
3 (DSL) - Body ground 20°C (68°F) 11 to 13 Ω




OK

3.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)

NG

4.INSPECT SHIFT SOLENOID VALVE DSL
3.CHECK WIRE HARNESS (TRANSMISSION WIRE - ECM)
U189336E02
1.823,1.969 2.031,2.625 true 1.531,0.917 1.906,1.146 0.375,0.229 10 false D2 1.938,2.656 2.344,2.854 0.406,0.198 10 false DSL 0.135,0.104 1.521,0.271 1.385,0.167 10 false Wire Harness Side:

a.

Connect the D51 wire connector.


b.

Disconnect the D2 ECM connector.


c.

Measure the resistance of the wire harness side connector.

Standard resistance:
Tester Connection Condition Specified Condition
D2-79 (DSL) - Body ground 20°C (68°F) 11 to 13 Ω




OK

4.INSPECT SHIFT SOLENOID VALVE DSL

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.INSPECT SHIFT SOLENOID VALVE DSL
A112706E01
1.27,2.578 1.524,2.787 0.255,0.209 10 (-) 1.931,2.578 2.185,2.787 0.255,0.209 10 (+)

a.

Remove the shift solenoid valve DSL.


b.

Measure the resistance of the solenoid valve.

Standard resistance:

11 to 13 Ω at 20°C (68°F)



c.

Connect the battery's positive (+) lead to the terminal of the solenoid valve connector, and the negative (-) lead to the solenoid body. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes operating noise.




OK

5.CHECK TRANSMISSION WIRE

NG

REPLACE SHIFT SOLENOID VALVE DSL

5.CHECK TRANSMISSION WIRE
OK:

The connectors and pins are securely installed.

There is no open or short on the wire harness.



OK

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION WIRE

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

OK:

There are no foreign objects on each valve.




OK

7.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

7.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly (see page Drivetrain>U241E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION).

OK:

The torque converter assembly operates normally.




OK

REPAIR AUTOMATIC TRANSAXLE ASSEMBLY

NG

REPLACE TORQUE CONVERTER ASSEMBLY